On 7/12/23 04:47, Naresh Solanki wrote:
From: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
Add support for MP2971 and MP2973, the successor of MP2975.
The major differences are:
- On MP2973 and MP2971 the Vref cannot be read and thus most of
the OVP/current calculations won't work.
- MP2973 and MP2971 also support LINEAR format for VOUT
- MP2973 and MP2971 do not support OVP2
- On MP2973 and MP2971 most registers are in LINEAR format
- The IMVP9_EN bit has a different position
- Per phase current sense haven't been implemented.
As on MP2975 most of the FAULT_LIMIT and WARN_LIMIT registers
have been redefined and doesn't provide the functionality as
defined in PMBUS spec.
Tested on MP2973 and MP2971.
Signed-off-by: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx>
Signed-off-by: Naresh Solanki <Naresh.Solanki@xxxxxxxxxxxxx>
---
drivers/hwmon/pmbus/mp2975.c | 262 +++++++++++++++++++++++++++++------
1 file changed, 221 insertions(+), 41 deletions(-)
diff --git a/drivers/hwmon/pmbus/mp2975.c b/drivers/hwmon/pmbus/mp2975.c
index 13d8b95eb992..83242595ccbe 100644
--- a/drivers/hwmon/pmbus/mp2975.c
+++ b/drivers/hwmon/pmbus/mp2975.c
@@ -35,6 +35,8 @@
#define MP2975_MFR_OVP_TH_SET 0xe5
#define MP2975_MFR_UVP_SET 0xe6
+#define MP2973_MFR_RESO_SET 0xc7
+
#define MP2975_VOUT_FORMAT BIT(15)
#define MP2975_VID_STEP_SEL_R1 BIT(4)
#define MP2975_IMVP9_EN_R1 BIT(13)
@@ -49,8 +51,32 @@
#define MP2975_SENSE_AMPL_HALF 2
#define MP2975_VIN_UV_LIMIT_UNIT 8
+#define MP2973_VOUT_FORMAT_R1 GENMASK(7, 6)
+#define MP2973_VOUT_FORMAT_R2 GENMASK(4, 3)
+#define MP2973_VOUT_FORMAT_DIRECT_R1 BIT(7)
+#define MP2973_VOUT_FORMAT_LINEAR_R1 BIT(6)
+#define MP2973_VOUT_FORMAT_DIRECT_R2 BIT(4)
+#define MP2973_VOUT_FORMAT_LINEAR_R2 BIT(3)
+
+#define MP2973_MFR_VR_MULTI_CONFIG_R1 0x0d
+#define MP2973_MFR_VR_MULTI_CONFIG_R2 0x1d
+#define MP2973_VID_STEP_SEL_R1 BIT(4)
+#define MP2973_IMVP9_EN_R1 BIT(14)
+#define MP2973_VID_STEP_SEL_R2 BIT(3)
+#define MP2973_IMVP9_EN_R2 BIT(13)
+
+#define MP2973_MFR_READ_IOUT_PK 0x90
+#define MP2973_MFR_READ_POUT_PK 0x91
+
#define MP2975_MAX_PHASE_RAIL1 8
#define MP2975_MAX_PHASE_RAIL2 4
+
+#define MP2973_MAX_PHASE_RAIL1 14
+#define MP2973_MAX_PHASE_RAIL2 6
+
+#define MP2971_MAX_PHASE_RAIL1 8
+#define MP2971_MAX_PHASE_RAIL2 3
+
#define MP2975_PAGE_NUM 2
#define MP2975_RAIL2_FUNC (PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | \
@@ -58,11 +84,13 @@
PMBUS_HAVE_POUT | PMBUS_PHASE_VIRTUAL)
enum chips {
- mp2975
+ mp2971, mp2973, mp2975
};
static const int mp2975_max_phases[][MP2975_PAGE_NUM] = {
[mp2975] = { MP2975_MAX_PHASE_RAIL1, MP2975_MAX_PHASE_RAIL2 },
+ [mp2973] = { MP2973_MAX_PHASE_RAIL1, MP2973_MAX_PHASE_RAIL2 },
+ [mp2971] = { MP2971_MAX_PHASE_RAIL1, MP2971_MAX_PHASE_RAIL2 },
};
struct mp2975_data {
@@ -79,6 +107,8 @@ struct mp2975_data {
};
static const struct i2c_device_id mp2975_id[] = {
+ {"mp2971", mp2971},
+ {"mp2973", mp2973},
{"mp2975", mp2975},
{}
};
@@ -215,6 +245,76 @@ mp2975_read_phases(struct i2c_client *client, struct mp2975_data *data,
return ret;
}
+static int mp2973_read_word_data(struct i2c_client *client, int page,
+ int phase, int reg)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct mp2975_data *data = to_mp2975_data(info);
+ int ret;
+
+ switch (reg) {
+ case PMBUS_OT_FAULT_LIMIT:
+ ret = mp2975_read_word_helper(client, page, phase, reg,
+ GENMASK(7, 0));
+ break;
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ ret = mp2975_read_word_helper(client, page, phase, reg,
+ GENMASK(7, 0));
+ if (ret < 0)
+ return ret;
+
+ ret = DIV_ROUND_CLOSEST(ret, MP2975_VIN_UV_LIMIT_UNIT);
+ break;
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ /*
+ * MP2971 and mp2973 only supports tracking (ovp1) mode.
+ */
+ ret = mp2975_read_word_helper(client, page, phase,
+ MP2975_MFR_OVP_TH_SET,
+ GENMASK(2, 0));
+ if (ret < 0)
+ return ret;
+
+ ret = data->vout_max[page] + 50 * (ret + 1);
+ break;
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ ret = mp2975_read_word_helper(client, page, phase, reg,
+ GENMASK(8, 0));
+ if (ret < 0)
+ return ret;
+ ret = mp2975_vid2direct(info->vrm_version[page], ret);
+ break;
+ case PMBUS_VIRT_READ_POUT_MAX:
+ ret = pmbus_read_word_data(client, page, phase,
+ MP2973_MFR_READ_POUT_PK);
+ break;
+ case PMBUS_VIRT_READ_IOUT_MAX:
+ ret = pmbus_read_word_data(client, page, phase,
+ MP2973_MFR_READ_IOUT_PK);
+ break;
+ case PMBUS_UT_WARN_LIMIT:
+ case PMBUS_UT_FAULT_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_WARN_LIMIT:
+ case PMBUS_VOUT_OV_WARN_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_IIN_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_UC_FAULT_LIMIT:
+ case PMBUS_POUT_OP_FAULT_LIMIT:
+ case PMBUS_POUT_OP_WARN_LIMIT:
+ case PMBUS_PIN_OP_WARN_LIMIT:
+ return -ENXIO;
+ default:
+ return -ENODATA;
+ }
+
+ return ret;
+}
+
static int mp2975_read_word_data(struct i2c_client *client, int page,
int phase, int reg)
{
@@ -386,7 +486,7 @@ mp2975_identify_multiphase(struct i2c_client *client, struct mp2975_data *data,
}
static int
-mp2975_identify_vid(struct i2c_client *client, struct mp2975_data *data,
+mp297x_identify_vid(struct i2c_client *client, struct mp2975_data *data,
Please refrain from such cosmetic changes. It is perfectly fine to keep
calling the function mp2975_identify_vid() even if it is called for
other chips.
Those changes only make it more difficult to review your patch and,
on top of that, are not really related to introducing support for
the new chips.
struct pmbus_driver_info *info, u32 reg, int page,
u32 imvp_bit, u32 vr_bit)
{
@@ -422,7 +522,7 @@ mp2975_identify_rails_vid(struct i2c_client *client, struct mp2975_data *data,
return ret;
/* Identify VID mode for rail 1. */
- ret = mp2975_identify_vid(client, data, info,
+ ret = mp297x_identify_vid(client, data, info,
MP2975_MFR_VR_MULTI_CONFIG_R1, 0,
MP2975_IMVP9_EN_R1, MP2975_VID_STEP_SEL_R1);
if (ret < 0)
@@ -430,10 +530,39 @@ mp2975_identify_rails_vid(struct i2c_client *client, struct mp2975_data *data,
/* Identify VID mode for rail 2, if connected. */
if (info->phases[1])
- ret = mp2975_identify_vid(client, data, info,
+ ret = mp297x_identify_vid(client, data, info,
MP2975_MFR_VR_MULTI_CONFIG_R2, 1,
MP2975_IMVP9_EN_R2,
MP2975_VID_STEP_SEL_R2);
+
+ return ret;
+}
+
+static int
+mp2973_identify_rails_vid(struct i2c_client *client, struct mp2975_data *data,
+ struct pmbus_driver_info *info)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 2);
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 1. */
+ ret = mp297x_identify_vid(client, data, info,
+ MP2973_MFR_VR_MULTI_CONFIG_R1, 0,
+ MP2973_IMVP9_EN_R1, MP2973_VID_STEP_SEL_R1);
+
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 2, if connected. */
+ if (info->phases[1])
+ ret = mp297x_identify_vid(client, data, info,
+ MP2973_MFR_VR_MULTI_CONFIG_R2, 1,
+ MP2973_IMVP9_EN_R2,
+ MP2973_VID_STEP_SEL_R2);
+
return ret;
}
@@ -532,7 +661,7 @@ mp2975_vref_offset_get(struct i2c_client *client, struct mp2975_data *data,
}
static int
-mp2975_vout_max_get(struct i2c_client *client, struct mp2975_data *data,
+mp297x_vout_max_get(struct i2c_client *client, struct mp2975_data *data,
struct pmbus_driver_info *info, int page)
{
int ret;
@@ -548,17 +677,33 @@ mp2975_vout_max_get(struct i2c_client *client, struct mp2975_data *data,
}
static int
-mp2975_set_vout_format(struct i2c_client *client,
+mp297x_set_vout_format(struct i2c_client *client,
struct mp2975_data *data, int page)
{
int ret;
- ret = i2c_smbus_read_word_data(client, MP2975_MFR_DC_LOOP_CTRL);
- if (ret < 0)
- return ret;
/* Enable DIRECT VOUT format 1mV/LSB */
- ret &= ~MP2975_VOUT_FORMAT;
- ret = i2c_smbus_write_word_data(client, MP2975_MFR_DC_LOOP_CTRL, ret);
+ if (data->chip_id == mp2975) {
+ ret = i2c_smbus_read_word_data(client, MP2975_MFR_DC_LOOP_CTRL);
+ if (ret < 0)
+ return ret;
+ ret &= ~MP2975_VOUT_FORMAT;
+ ret = i2c_smbus_write_word_data(client, MP2975_MFR_DC_LOOP_CTRL, ret);
+ } else {
+ ret = i2c_smbus_read_word_data(client, MP2973_MFR_RESO_SET);
+ if (ret < 0)
+ return ret;
+
+ if (page == 0) {
+ ret &= ~MP2973_VOUT_FORMAT_R1;
+ ret |= MP2973_VOUT_FORMAT_DIRECT_R1;
+ } else {
+ ret &= ~MP2973_VOUT_FORMAT_R2;
+ ret |= MP2973_VOUT_FORMAT_DIRECT_R2;
+ }
+
+ ret = i2c_smbus_write_word_data(client, MP2973_MFR_RESO_SET, ret);
Same as with the previous patch: The value only needs to be written back if it differs
from the value already configured in the chip.
+ }
return ret;
}
@@ -605,24 +750,28 @@ mp2975_vout_per_rail_config_get(struct i2c_client *client,
for (i = 0; i < data->info.pages; i++) {
ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, i);
if (ret < 0)
- return ret;
+ continue;
- /* Obtain voltage reference offsets. */
- ret = mp2975_vref_offset_get(client, data, i);
+ /*
+ * Set VOUT format for READ_VOUT command : direct.
+ * Pages on same device can be configured with different
+ * formats.
+ */
+ ret = mp297x_set_vout_format(client, data, i);
if (ret < 0)
return ret;
/* Obtain maximum voltage values. */
- ret = mp2975_vout_max_get(client, data, info, i);
+ ret = mp297x_vout_max_get(client, data, info, i);
if (ret < 0)
return ret;
- /*
- * Set VOUT format for READ_VOUT command : direct.
- * Pages on same device can be configured with different
- * formats.
- */
- ret = mp2975_set_vout_format(client, data, i);
+ /* Skip if reading Vref is unsupported */
+ if (data->chip_id != mp2975)
+ continue;
+
+ /* Obtain voltage reference offsets. */
+ ret = mp2975_vref_offset_get(client, data, i);
if (ret < 0)
return ret;
@@ -660,6 +809,23 @@ static struct pmbus_driver_info mp2975_info = {
.read_word_data = mp2975_read_word_data,
};
+static struct pmbus_driver_info mp2973_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = direct,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .m[PSC_VOLTAGE_OUT] = 1,
+ .R[PSC_VOLTAGE_OUT] = 3,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP | PMBUS_HAVE_POUT |
+ PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT,
+ .read_word_data = mp2973_read_word_data,
+};
+
static int mp2975_probe(struct i2c_client *client)
{
struct pmbus_driver_info *info;
@@ -679,6 +845,11 @@ static int mp2975_probe(struct i2c_client *client)
memcpy(data->max_phases, mp2975_max_phases[data->chip_id],
sizeof(data->max_phases));
+ if (data->chip_id == mp2975)
+ memcpy(&data->info, &mp2975_info, sizeof(*info));
+ else
+ memcpy(&data->info, &mp2973_info, sizeof(*info));
+
info = &data->info;
/* Identify multiphase configuration for rail 2. */
@@ -693,30 +864,37 @@ static int mp2975_probe(struct i2c_client *client)
data->info.func[1] = MP2975_RAIL2_FUNC;
}
- /* Identify multiphase configuration. */
- ret = mp2975_identify_multiphase(client, data, info);
- if (ret)
- return ret;
+ if (data->chip_id == mp2975) {
+ /* Identify multiphase configuration. */
+ ret = mp2975_identify_multiphase(client, data, info);
+ if (ret)
+ return ret;
- /* Identify VID setting per rail. */
- ret = mp2975_identify_rails_vid(client, data, info);
- if (ret < 0)
- return ret;
+ /* Identify VID setting per rail. */
+ ret = mp2975_identify_rails_vid(client, data, info);
+ if (ret < 0)
+ return ret;
- /* Obtain current sense gain of power stage. */
- ret = mp2975_current_sense_gain_get(client, data);
- if (ret)
- return ret;
+ /* Obtain current sense gain of power stage. */
+ ret = mp2975_current_sense_gain_get(client, data);
+ if (ret)
+ return ret;
- /* Obtain voltage reference values. */
- ret = mp2975_vref_get(client, data, info);
- if (ret)
- return ret;
+ /* Obtain voltage reference values. */
+ ret = mp2975_vref_get(client, data, info);
+ if (ret)
+ return ret;
- /* Obtain vout over-voltage scales. */
- ret = mp2975_vout_ov_scale_get(client, data, info);
- if (ret < 0)
- return ret;
+ /* Obtain vout over-voltage scales. */
+ ret = mp2975_vout_ov_scale_get(client, data, info);
+ if (ret < 0)
+ return ret;
+ } else {
+ /* Identify VID setting per rail. */
+ ret = mp2973_identify_rails_vid(client, data, info);
+ if (ret < 0)
+ return ret;
+ }
/* Obtain offsets, maximum and format for vout. */
ret = mp2975_vout_per_rail_config_get(client, data, info);
@@ -727,6 +905,8 @@ static int mp2975_probe(struct i2c_client *client)
}
static const struct of_device_id __maybe_unused mp2975_of_match[] = {
+ {.compatible = "mps,mp2971", .data = (void *)mp2971},
+ {.compatible = "mps,mp2973", .data = (void *)mp2973},
{.compatible = "mps,mp2975", .data = (void *)mp2975},
{}
};
