[PATCH v2 5/5] iio: mlx90614: Add MLX90615 support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add support for MLX90615 Infra Red Thermometer, which seems to be
the predecesor of MLX90614 . There are significant differences in
the register layout compared to MLX90614, but the functionality
of the device is virtually identical.

The following differences have been identified:
- RAM/EEPROM/SLEEP access opcodes are different
- RAM/EEPROM registers are at different offsets
- EEPROM emissivity and configuration registers are at different offsets
- EEPROM configuration register bits are shuffled around
- EEPROM emissivity settings are 14 bit on MLX90615 , 16 bit on MLX90614
- MLX90615 can only ever support one sensor, MLX90614 could support two
- FIR filter is set to fixed settings on MLX90615
- IIR filter coefficients are different

This patch fills in the MLX90615 specific description and quirk handling.

Signed-off-by: Marek Vasut <marex@xxxxxxx>
---
NOTE: The IIR coefficients need to be checked
---
Cc: Crt Mori <cmo@xxxxxxxxxxx>
Cc: Jonathan Cameron <jic23@xxxxxxxxxx>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx>
Cc: Lars-Peter Clausen <lars@xxxxxxxxxx>
Cc: Marek Vasut <marex@xxxxxxx>
Cc: Peter Meerwald <pmeerw@xxxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: linux-iio@xxxxxxxxxxxxxxx
---
V2: Split the patch up into cleanups, abstraction and MLX90615 addition
---
 drivers/iio/temperature/mlx90614.c | 49 +++++++++++++++++++++++++++---
 1 file changed, 45 insertions(+), 4 deletions(-)

diff --git a/drivers/iio/temperature/mlx90614.c b/drivers/iio/temperature/mlx90614.c
index d6d2a5afaf8c0..5bcd323921db5 100644
--- a/drivers/iio/temperature/mlx90614.c
+++ b/drivers/iio/temperature/mlx90614.c
@@ -1,12 +1,15 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * mlx90614.c - Support for Melexis MLX90614 contactless IR temperature sensor
+ * mlx90614.c - Support for Melexis MLX90614/MLX90615 contactless IR temperature sensor
  *
  * Copyright (c) 2014 Peter Meerwald <pmeerw@xxxxxxxxxx>
  * Copyright (c) 2015 Essensium NV
  * Copyright (c) 2015 Melexis
  *
- * Driver for the Melexis MLX90614 I2C 16-bit IR thermopile sensor
+ * Driver for the Melexis MLX90614/MLX90615 I2C 16-bit IR thermopile sensor
+ *
+ * MLX90614 - 17-bit ADC + MLX90302 DSP
+ * MLX90615 - 16-bit ADC + MLX90325 DSP
  *
  * (7-bit I2C slave address 0x5a, 100KHz bus speed only!)
  *
@@ -35,6 +38,10 @@
 #define MLX90614_OP_EEPROM	0x20
 #define MLX90614_OP_SLEEP	0xff
 
+#define MLX90615_OP_EEPROM	0x10
+#define MLX90615_OP_RAM		0x20
+#define MLX90615_OP_SLEEP	0xc6
+
 /* Control bits in configuration register */
 #define MLX90614_CONFIG_IIR_SHIFT 0 /* IIR coefficient */
 #define MLX90614_CONFIG_IIR_MASK (0x7 << MLX90614_CONFIG_IIR_SHIFT)
@@ -43,11 +50,16 @@
 #define MLX90614_CONFIG_FIR_SHIFT 8 /* FIR coefficient */
 #define MLX90614_CONFIG_FIR_MASK (0x7 << MLX90614_CONFIG_FIR_SHIFT)
 
+#define MLX90615_CONFIG_IIR_SHIFT 12 /* IIR coefficient */
+#define MLX90615_CONFIG_IIR_MASK (0x7 << MLX90615_CONFIG_IIR_SHIFT)
+
 /* Timings (in ms) */
 #define MLX90614_TIMING_EEPROM 20 /* time for EEPROM write/erase to complete */
 #define MLX90614_TIMING_WAKEUP 34 /* time to hold SDA low for wake-up */
 #define MLX90614_TIMING_STARTUP 250 /* time before first data after wake-up */
 
+#define MLX90615_TIMING_WAKEUP 22 /* time to hold SCL low for wake-up */
+
 #define MLX90614_AUTOSLEEP_DELAY 5000 /* default autosleep delay */
 
 /* Magic constants */
@@ -306,8 +318,8 @@ static int mlx90614_read_raw(struct iio_dev *indio_dev,
 			*val2 = ret * chip_info->emissivity_res;
 		}
 		return IIO_VAL_INT_PLUS_NANO;
-	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: /* IIR setting with
-							     FIR = 1024 */
+	/* IIR setting with FIR=1024 (MLX90614) or FIR=65536 (MLX90615) */
+	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
 		ret = mlx90614_power_get(data, false);
 		if (ret < 0)
 			return ret;
@@ -666,14 +678,43 @@ static const struct mlx_chip_info mlx90614_chip_info = {
 	},
 };
 
+static const struct mlx_chip_info mlx90615_chip_info = {
+	.op_eeprom_emissivity		= MLX90615_OP_EEPROM | 0x03,
+	.op_eeprom_config1		= MLX90615_OP_EEPROM | 0x02,
+	.op_ram_ta			= MLX90615_OP_RAM | 0x06,
+	.op_ram_tobj1			= MLX90615_OP_RAM | 0x07,
+	.op_ram_tobj2			= MLX90615_OP_RAM | 0x08,
+	.op_sleep			= MLX90615_OP_SLEEP,
+	.dual_channel			= false,
+	.wakeup_delay_ms		= MLX90615_TIMING_WAKEUP,
+	.emissivity_max			= 16383,
+	.emissivity_res			= 1000000000 / 16383,
+	.fir_config_mask		= 0,	/* MLX90615 FIR is fixed */
+	.iir_config_mask		= MLX90615_CONFIG_IIR_MASK,
+	/* IIR value 0 is FORBIDDEN COMBINATION on MLX90615 */
+	.iir_valid_offset		= 1,
+	.iir_values			= { 723, 77, 42, 31, 28, 20, 18 },
+	.iir_freqs			= {
+		{ 0, 180000 },	/* 14% ~= 0.18 Hz */
+		{ 0, 200000 },	/* 17% ~= 0.20 Hz */
+		{ 0, 280000 },	/* 20% ~= 0.28 Hz */
+		{ 0, 310000 },	/* 25% ~= 0.31 Hz */
+		{ 0, 420000 },	/* 33% ~= 0.42 Hz */
+		{ 0, 770000 },	/* 50% ~= 0.77 Hz */
+		{ 7, 230000 },	/* 100% ~= 7.23 Hz */
+	},
+};
+
 static const struct i2c_device_id mlx90614_id[] = {
 	{ "mlx90614", .driver_data = (kernel_ulong_t)&mlx90614_chip_info },
+	{ "mlx90615", .driver_data = (kernel_ulong_t)&mlx90615_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, mlx90614_id);
 
 static const struct of_device_id mlx90614_of_match[] = {
 	{ .compatible = "melexis,mlx90614", .data = &mlx90614_chip_info },
+	{ .compatible = "melexis,mlx90615", .data = &mlx90615_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, mlx90614_of_match);
-- 
2.39.2




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux