Enable USB3 controller, phy and typec related nodes.
Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
---
arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 87 +++++++++++++++++++
1 file changed, 87 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index afa883389456..64f20ff44ba7 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -6,6 +6,7 @@
/dts-v1/;
#include "imx8qxp.dtsi"
+#include <dt-bindings/usb/pd.h>
/ {
model = "Freescale i.MX8QXP MEK";
@@ -28,6 +29,21 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
gpio = <&lsio_gpio4 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ gpio-sbu-mux {
+ compatible = "gpio-sbu-mux";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec_mux>;
+ select-gpios = <&lsio_gpio5 9 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&pca9557_a 7 GPIO_ACTIVE_LOW>;
+ orientation-switch;
+
+ port {
+ usb3_data_ss: endpoint {
+ remote-endpoint = <&typec_con_ss>;
+ };
+ };
+ };
};
&dsp {
@@ -127,6 +143,44 @@ light-sensor@44 {
};
};
};
+
+ ptn5110: tcpc@50 {
+ compatible = "nxp,ptn5110";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec>;
+ reg = <0x50>;
+
+ interrupt-parent = <&lsio_gpio1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ status = "okay";
+
+ port {
+ typec_dr_sw: endpoint {
+ remote-endpoint = <&usb3_drd_sw>;
+ };
+ };
+
+ usb_con1: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "source";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ typec_con_ss: endpoint {
+ remote-endpoint = <&usb3_data_ss>;
+ };
+ };
+ };
+ };
+ };
+
};
&lpuart0 {
@@ -204,6 +258,27 @@ &usdhc2 {
status = "okay";
};
+&usb3_phy {
+ status = "okay";
+};
+
+&usbotg3 {
+ status = "okay";
+};
+
+&usbotg3_cdns3 {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb3_drd_sw: endpoint {
+ remote-endpoint = <&typec_dr_sw>;
+ };
+ };
+};
+
+
&vpu {
compatible = "nxp,imx8qxp-vpu";
status = "okay";
@@ -267,6 +342,18 @@ IMX8QXP_UART0_TX_ADMA_UART0_TX 0x06000020
>;
};
+ pinctrl_typec: typecgrp {
+ fsl,pins = <
+ IMX8QXP_SPI2_SCK_LSIO_GPIO1_IO03 0x06000021
+ >;
+ };
+
+ pinctrl_typec_mux: typecmuxgrp {
+ fsl,pins = <
+ IMX8QXP_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09 0x60
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
--
2.34.1
