On Mon, Feb 13, 2023 at 05:22:28PM -0500, Frank Li wrote:
> Enable USB3 controller, phy and typec related nodes.
>
> Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
> ---
> arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 87 +++++++++++++++++++
> 1 file changed, 87 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
> index afa883389456..64f20ff44ba7 100644
> --- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
> @@ -6,6 +6,7 @@
> /dts-v1/;
>
> #include "imx8qxp.dtsi"
> +#include <dt-bindings/usb/pd.h>
>
> / {
> model = "Freescale i.MX8QXP MEK";
> @@ -28,6 +29,21 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
> gpio = <&lsio_gpio4 19 GPIO_ACTIVE_HIGH>;
> enable-active-high;
> };
> +
> + gpio-sbu-mux {
> + compatible = "gpio-sbu-mux";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_typec_mux>;
> + select-gpios = <&lsio_gpio5 9 GPIO_ACTIVE_LOW>;
> + enable-gpios = <&pca9557_a 7 GPIO_ACTIVE_LOW>;
> + orientation-switch;
> +
> + port {
> + usb3_data_ss: endpoint {
> + remote-endpoint = <&typec_con_ss>;
> + };
> + };
> + };
> };
>
> &dsp {
> @@ -127,6 +143,44 @@ light-sensor@44 {
> };
> };
> };
> +
> + ptn5110: tcpc@50 {
> + compatible = "nxp,ptn5110";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_typec>;
> + reg = <0x50>;
> +
Unneeded newline.
> + interrupt-parent = <&lsio_gpio1>;
> + interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> + status = "okay";
Unneeded "okay" status.
> +
> + port {
> + typec_dr_sw: endpoint {
> + remote-endpoint = <&usb3_drd_sw>;
> + };
> + };
> +
> + usb_con1: connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "source";
> + data-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <1>;
> + typec_con_ss: endpoint {
Broken indent alignment.
Shawn
> + remote-endpoint = <&usb3_data_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> };
>
> &lpuart0 {
> @@ -204,6 +258,27 @@ &usdhc2 {
> status = "okay";
> };
>
> +&usb3_phy {
> + status = "okay";
> +};
> +
> +&usbotg3 {
> + status = "okay";
> +};
> +
> +&usbotg3_cdns3 {
> + dr_mode = "otg";
> + usb-role-switch;
> + status = "okay";
> +
> + port {
> + usb3_drd_sw: endpoint {
> + remote-endpoint = <&typec_dr_sw>;
> + };
> + };
> +};
> +
> +
> &vpu {
> compatible = "nxp,imx8qxp-vpu";
> status = "okay";
> @@ -267,6 +342,18 @@ IMX8QXP_UART0_TX_ADMA_UART0_TX 0x06000020
> >;
> };
>
> + pinctrl_typec: typecgrp {
> + fsl,pins = <
> + IMX8QXP_SPI2_SCK_LSIO_GPIO1_IO03 0x06000021
> + >;
> + };
> +
> + pinctrl_typec_mux: typecmuxgrp {
> + fsl,pins = <
> + IMX8QXP_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09 0x60
> + >;
> + };
> +
> pinctrl_usdhc1: usdhc1grp {
> fsl,pins = <
> IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
> --
> 2.34.1
>
