On 15/12/2022 10:02:09-0500, Hugo Villeneuve wrote:
> From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
>
> The PCF2127 and PCF2129 have one output interrupt pin. The PCF2131 has
> two, named INT_A and INT_B. The hardware support that any interrupt
> source can be routed to either one or both of them.
>
> Force all interrupt sources to go to the INT A pin.
>
> Support to route any interrupt source to INT A/B pins is not supported
> by this driver at the moment.
>
The main issue with this is that this will created a breaking change
once someone needs support for INTB
> Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
> ---
> drivers/rtc/rtc-pcf2127.c | 35 +++++++++++++++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
>
> diff --git a/drivers/rtc/rtc-pcf2127.c b/drivers/rtc/rtc-pcf2127.c
> index 4148e135f935..68af4d0438b8 100644
> --- a/drivers/rtc/rtc-pcf2127.c
> +++ b/drivers/rtc/rtc-pcf2127.c
> @@ -191,6 +191,7 @@ struct pcf21xx_config {
> int max_register;
> unsigned int has_nvmem:1;
> unsigned int has_bit_wd_ctl_cd0:1;
> + unsigned int has_int_a_b:1; /* PCF2131 supports two interrupt outputs. */
> u8 regs_td_base; /* Time/data base registers. */
> u8 regs_alarm_base; /* Alarm function base registers. */
> u8 reg_wd_ctl; /* Watchdog control register. */
> @@ -879,6 +880,7 @@ static struct pcf21xx_config pcf21xx_cfg[] = {
> .max_register = 0x1d,
> .has_nvmem = 1,
> .has_bit_wd_ctl_cd0 = 1,
> + .has_int_a_b = 0,
> .regs_td_base = PCF2127_REG_TIME_DATE_BASE,
> .regs_alarm_base = PCF2127_REG_ALARM_BASE,
> .reg_wd_ctl = PCF2127_REG_WD_CTL,
> @@ -902,6 +904,7 @@ static struct pcf21xx_config pcf21xx_cfg[] = {
> .max_register = 0x19,
> .has_nvmem = 0,
> .has_bit_wd_ctl_cd0 = 0,
> + .has_int_a_b = 0,
> .regs_td_base = PCF2127_REG_TIME_DATE_BASE,
> .regs_alarm_base = PCF2127_REG_ALARM_BASE,
> .reg_wd_ctl = PCF2127_REG_WD_CTL,
> @@ -925,6 +928,7 @@ static struct pcf21xx_config pcf21xx_cfg[] = {
> .max_register = 0x36,
> .has_nvmem = 0,
> .has_bit_wd_ctl_cd0 = 0,
> + .has_int_a_b = 1,
> .regs_td_base = PCF2131_REG_TIME_DATE_BASE,
> .regs_alarm_base = PCF2131_REG_ALARM_BASE,
> .reg_wd_ctl = PCF2131_REG_WD_CTL,
> @@ -1017,6 +1021,28 @@ static int pcf2127_enable_ts(struct device *dev, int ts_id)
> return ret;
> }
>
> +/* Route all interrupt sources to INT A pin. */
> +static int pcf2127_configure_interrupt_pins(struct device *dev)
> +{
> + struct pcf2127 *pcf2127 = dev_get_drvdata(dev);
> + int ret;
> +
> + /* Mask bits need to be cleared to enable corresponding
> + * interrupt source.
> + */
> + ret = regmap_write(pcf2127->regmap,
> + PCF2131_REG_INT_A_MASK1, 0);
> + if (ret)
> + return ret;
> +
> + ret = regmap_write(pcf2127->regmap,
> + PCF2131_REG_INT_A_MASK2, 0);
> + if (ret)
> + return ret;
> +
> + return ret;
> +}
> +
> static int pcf2127_probe(struct device *dev, struct regmap *regmap,
> int alarm_irq, const char *name, const struct pcf21xx_config *config)
> {
> @@ -1076,6 +1102,15 @@ static int pcf2127_probe(struct device *dev, struct regmap *regmap,
> set_bit(RTC_FEATURE_ALARM, pcf2127->rtc->features);
> }
>
> + if (pcf2127->cfg->has_int_a_b) {
> + /* Configure int A/B pins, independently of alarm_irq. */
> + ret = pcf2127_configure_interrupt_pins(dev);
> + if (ret) {
> + dev_err(dev, "failed to configure interrupt pins\n");
> + return ret;
> + }
> + }
> +
> if (pcf2127->cfg->has_nvmem) {
> struct nvmem_config nvmem_cfg = {
> .priv = pcf2127,
> --
> 2.30.2
>
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
