max6639_platform_data is not used by any in-kernel driver and does not address the MAX6639 fans separately. Move to device tree configuration with explicit properties to configure each fan. Signed-off-by: Marcello Sylvester Bauer <sylv@xxxxxxx> Signed-off-by: Naresh Solanki <Naresh.Solanki@xxxxxxxxxxxxx> --- drivers/hwmon/max6639.c | 246 +++++++++++++++++++------- include/linux/platform_data/max6639.h | 15 -- 2 files changed, 178 insertions(+), 83 deletions(-) delete mode 100644 include/linux/platform_data/max6639.h diff --git a/drivers/hwmon/max6639.c b/drivers/hwmon/max6639.c index 9b895402c80d..feafa3511297 100644 --- a/drivers/hwmon/max6639.c +++ b/drivers/hwmon/max6639.c @@ -19,7 +19,6 @@ #include <linux/hwmon-sysfs.h> #include <linux/err.h> #include <linux/mutex.h> -#include <linux/platform_data/max6639.h> /* Addresses to scan */ static const unsigned short normal_i2c[] = { 0x2c, 0x2e, 0x2f, I2C_CLIENT_END }; @@ -54,9 +53,12 @@ static const unsigned short normal_i2c[] = { 0x2c, 0x2e, 0x2f, I2C_CLIENT_END }; #define MAX6639_GCONFIG_PWM_FREQ_HI 0x08 #define MAX6639_FAN_CONFIG1_PWM 0x80 - +#define MAX6639_REG_FAN_CONFIG2a_PWM_POL 0x02 #define MAX6639_FAN_CONFIG3_THERM_FULL_SPEED 0x40 +#define MAX6639_FAN_CONFIG3_FREQ_MASK 0x03 +#define MAX6639_REG_TARGTDUTY_SLOT 120 +/* Tach supported range. This internally controls tach frequency */ static const int rpm_ranges[] = { 2000, 4000, 8000, 16000 }; #define FAN_FROM_REG(val, rpm_range) ((val) == 0 || (val) == 255 ? \ @@ -76,18 +78,21 @@ struct max6639_data { u16 temp[2]; /* Temperature, in 1/8 C, 0..255 C */ bool temp_fault[2]; /* Detected temperature diode failure */ u8 fan[2]; /* Register value: TACH count for fans >=30 */ + u32 target_rpm[2]; + u32 max_rpm[2]; + u8 pwm[2]; + u8 status; /* Detected channel alarms and fan failures */ /* Register values only written to */ - u8 pwm[2]; /* Register value: Duty cycle 0..120 */ u8 temp_therm[2]; /* THERM Temperature, 0..255 C (->_max) */ u8 temp_alert[2]; /* ALERT Temperature, 0..255 C (->_crit) */ u8 temp_ot[2]; /* OT Temperature, 0..255 C (->_emergency) */ /* Register values initialized only once */ - u8 ppr; /* Pulses per rotation 0..3 for 1..4 ppr */ - u8 rpm_range; /* Index in above rpm_ranges table */ - + u8 ppr[2]; /* Pulses per rotation 0..3 for 1..4 ppr */ + u8 rpm_range[2]; /* Index in above rpm_ranges table */ + u8 pwm_polarity[2]; /* Optional regulator for FAN supply */ struct regulator *reg; }; @@ -282,6 +287,7 @@ static ssize_t pwm_show(struct device *dev, struct device_attribute *dev_attr, struct max6639_data *data = dev_get_drvdata(dev); return sprintf(buf, "%d\n", data->pwm[attr->index] * 255 / 120); + } static ssize_t pwm_store(struct device *dev, @@ -302,10 +308,10 @@ static ssize_t pwm_store(struct device *dev, mutex_lock(&data->update_lock); data->pwm[attr->index] = (u8)(val * 120 / 255); - i2c_smbus_write_byte_data(client, - MAX6639_REG_TARGTDUTY(attr->index), - data->pwm[attr->index]); + i2c_smbus_write_byte_data(client, MAX6639_REG_TARGTDUTY(attr->index), + data->pwm[attr->index]); mutex_unlock(&data->update_lock); + return count; } @@ -319,7 +325,7 @@ static ssize_t fan_input_show(struct device *dev, return PTR_ERR(data); return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[attr->index], - data->rpm_range)); + data->rpm_range[attr->index])); } static ssize_t alarm_show(struct device *dev, @@ -386,29 +392,40 @@ static struct attribute *max6639_attrs[] = { ATTRIBUTE_GROUPS(max6639); /* - * returns respective index in rpm_ranges table - * 1 by default on invalid range + * Get respective index in rpm_ranges table */ -static int rpm_range_to_reg(int range) +static int rpm_range_to_index(struct device *dev, u8 *index, int rpm) { - int i; - - for (i = 0; i < ARRAY_SIZE(rpm_ranges); i++) { - if (rpm_ranges[i] == range) - return i; + if (rpm < 0) + return -EINVAL; + + /* Set index based on chip support */ + switch (rpm) { + case 0 ... 2000: + *index = 0; + break; + case 2001 ... 4000: + *index = 1; + break; + case 4001 ... 8000: + *index = 2; + break; + case 8001 ... 16000: + *index = 3; + break; + default: + /* Use max range for higher RPM */ + dev_warn(dev, + "RPM higher than supported range. Default to 16000 RPM"); + *index = 3; } - - return 1; /* default: 4000 RPM */ + return 0; } static int max6639_init_client(struct i2c_client *client, struct max6639_data *data) { - struct max6639_platform_data *max6639_info = - dev_get_platdata(&client->dev); - int i; - int rpm_range = 1; /* default: 4000 RPM */ - int err; + int i, err; /* Reset chip to default values, see below for GCONFIG setup */ err = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, @@ -416,51 +433,29 @@ static int max6639_init_client(struct i2c_client *client, if (err) goto exit; - /* Fans pulse per revolution is 2 by default */ - if (max6639_info && max6639_info->ppr > 0 && - max6639_info->ppr < 5) - data->ppr = max6639_info->ppr; - else - data->ppr = 2; - data->ppr -= 1; - - if (max6639_info) - rpm_range = rpm_range_to_reg(max6639_info->rpm_range); - data->rpm_range = rpm_range; - for (i = 0; i < 2; i++) { /* Set Fan pulse per revolution */ - err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_PPR(i), - data->ppr << 6); + err = i2c_smbus_write_byte_data(client, MAX6639_REG_FAN_PPR(i), + data->ppr[i] << 6); if (err) goto exit; /* Fans config PWM, RPM */ err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG1(i), - MAX6639_FAN_CONFIG1_PWM | rpm_range); - if (err) - goto exit; - - /* Fans PWM polarity high by default */ - if (max6639_info && max6639_info->pwm_polarity == 0) - err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG2a(i), 0x00); - else - err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG2a(i), 0x02); + MAX6639_REG_FAN_CONFIG1(i), + MAX6639_FAN_CONFIG1_PWM | + data->rpm_range[i]); if (err) goto exit; /* - * /THERM full speed enable, + * /THERM full speed disable, * PWM frequency 25kHz, see also GCONFIG below */ err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG3(i), - MAX6639_FAN_CONFIG3_THERM_FULL_SPEED | 0x03); + MAX6639_REG_FAN_CONFIG3(i), + 0x03); if (err) goto exit; @@ -469,31 +464,34 @@ static int max6639_init_client(struct i2c_client *client, data->temp_alert[i] = 90; data->temp_ot[i] = 100; err = i2c_smbus_write_byte_data(client, - MAX6639_REG_THERM_LIMIT(i), - data->temp_therm[i]); + MAX6639_REG_THERM_LIMIT(i), + data->temp_therm[i]); if (err) goto exit; err = i2c_smbus_write_byte_data(client, - MAX6639_REG_ALERT_LIMIT(i), - data->temp_alert[i]); + MAX6639_REG_ALERT_LIMIT(i), + data->temp_alert[i]); if (err) goto exit; err = i2c_smbus_write_byte_data(client, - MAX6639_REG_OT_LIMIT(i), data->temp_ot[i]); + MAX6639_REG_OT_LIMIT(i), + data->temp_ot[i]); if (err) goto exit; /* PWM 120/120 (i.e. 100%) */ - data->pwm[i] = 120; - err = i2c_smbus_write_byte_data(client, - MAX6639_REG_TARGTDUTY(i), data->pwm[i]); + data->pwm[i] = data->target_rpm[i]; + err = i2c_smbus_write_byte_data(client, MAX6639_REG_TARGTDUTY(i), data->pwm[i]); + if (err) goto exit; + } /* Start monitoring */ err = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, MAX6639_GCONFIG_DISABLE_TIMEOUT | MAX6639_GCONFIG_CH2_LOCAL | MAX6639_GCONFIG_PWM_FREQ_HI); + exit: return err; } @@ -524,12 +522,95 @@ static void max6639_regulator_disable(void *data) regulator_disable(data); } +static int max6639_probe_child_from_dt(struct i2c_client *client, + struct device_node *child, + struct max6639_data *data) + +{ + struct device *dev = &client->dev; + u32 i, maxrpm; + int val, err; + + err = of_property_read_u32(child, "reg", &i); + if (err) { + dev_err(dev, "missing reg property of %pOFn\n", child); + return err; + } + + if (i >= 2) { + dev_err(dev, "invalid reg %d of %pOFn\n", i, child); + return -EINVAL; + } + + err = of_property_read_u32(child, "pulses-per-revolution", &val); + if (err) { + dev_err(dev, "missing pulses-per-revolution property of %pOFn", + child); + return err; + } + + if (val < 0 || val > 5) { + dev_err(dev, "invalid pulses-per-revolution %d of %pOFn\n", val, + child); + return -EINVAL; + } + data->ppr[i] = val; + + err = of_property_read_u32(child, "max-rpm", &maxrpm); + if (err) { + dev_err(dev, "missing max-rpm property of %pOFn\n", child); + return err; + } + + err = rpm_range_to_index(dev, &data->rpm_range[i], maxrpm); + if (err) { + dev_err(dev, "invalid max-rpm %d of %pOFn\n", maxrpm, child); + return err; + } + data->max_rpm[i] = maxrpm; + + err = of_property_read_u32(child, "target-rpm", &val); + /* Use provided target RPM else default to maxrpm */ + if (!err) + data->target_rpm[i] = val; + else + data->target_rpm[i] = maxrpm; + + return 0; +} + +static int max6639_probe_from_dt(struct i2c_client *client, + struct max6639_data *data) +{ + struct device *dev = &client->dev; + const struct device_node *np = dev->of_node; + struct device_node *child; + int err; + + /* Compatible with non-DT platforms */ + if (!np) + return 0; + + for_each_child_of_node(np, child) { + if (strcmp(child->name, "fan")) + continue; + + err = max6639_probe_child_from_dt(client, child, data); + if (err) { + of_node_put(child); + return err; + } + } + + return 0; +} + static int max6639_probe(struct i2c_client *client) { struct device *dev = &client->dev; struct max6639_data *data; struct device *hwmon_dev; - int err; + int err, i; data = devm_kzalloc(dev, sizeof(struct max6639_data), GFP_KERNEL); if (!data) @@ -539,9 +620,11 @@ static int max6639_probe(struct i2c_client *client) data->reg = devm_regulator_get_optional(dev, "fan"); if (IS_ERR(data->reg)) { - if (PTR_ERR(data->reg) != -ENODEV) - return PTR_ERR(data->reg); - + if (PTR_ERR(data->reg) != -ENODEV) { + err = (int)PTR_ERR(data->reg); + return dev_err_probe(dev, err, + "Failed looking up fan supply\n"); + } data->reg = NULL; } else { /* Spin up fans */ @@ -560,6 +643,22 @@ static int max6639_probe(struct i2c_client *client) mutex_init(&data->update_lock); + /* Below are defaults later overridden by DT properties */ + for (i = 0; i < 2; i++) { + /* 4000 RPM */ + data->rpm_range[i] = 1; + data->ppr[i] = 2; + /* Max. temp. 80C/90C/100C */ + data->temp_therm[i] = 80; + data->temp_alert[i] = 90; + data->temp_ot[i] = 100; + } + + /* Probe from DT to get configuration */ + err = max6639_probe_from_dt(client, data); + if (err) + return err; + /* Initialize the max6639 chip */ err = max6639_init_client(client, data); if (err < 0) @@ -571,6 +670,7 @@ static int max6639_probe(struct i2c_client *client) return PTR_ERR_OR_ZERO(hwmon_dev); } +#if IS_ENABLED(CONFIG_PM_SLEEP) static int max6639_suspend(struct device *dev) { struct i2c_client *client = to_i2c_client(dev); @@ -608,6 +708,7 @@ static int max6639_resume(struct device *dev) return i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, ret & ~MAX6639_GCONFIG_STANDBY); } +#endif static const struct i2c_device_id max6639_id[] = { {"max6639", 0}, @@ -616,13 +717,22 @@ static const struct i2c_device_id max6639_id[] = { MODULE_DEVICE_TABLE(i2c, max6639_id); -static DEFINE_SIMPLE_DEV_PM_OPS(max6639_pm_ops, max6639_suspend, max6639_resume); +#ifdef CONFIG_OF +static const struct of_device_id maxim_of_platform_match[] = { + {.compatible = "maxim,max6639"}, + {}, +}; +MODULE_DEVICE_TABLE(of, maxim_of_platform_match); +#endif + +static SIMPLE_DEV_PM_OPS(max6639_pm_ops, max6639_suspend, max6639_resume); static struct i2c_driver max6639_driver = { .class = I2C_CLASS_HWMON, .driver = { .name = "max6639", .pm = pm_sleep_ptr(&max6639_pm_ops), + .of_match_table = of_match_ptr(maxim_of_platform_match), }, .probe_new = max6639_probe, .id_table = max6639_id, diff --git a/include/linux/platform_data/max6639.h b/include/linux/platform_data/max6639.h deleted file mode 100644 index 65bfdb4fdc15..000000000000 --- a/include/linux/platform_data/max6639.h +++ /dev/null @@ -1,15 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -#ifndef _LINUX_MAX6639_H -#define _LINUX_MAX6639_H - -#include <linux/types.h> - -/* platform data for the MAX6639 temperature sensor and fan control */ - -struct max6639_platform_data { - bool pwm_polarity; /* Polarity low (0) or high (1, default) */ - int ppr; /* Pulses per rotation 1..4 (default == 2) */ - int rpm_range; /* 2000, 4000 (default), 8000 or 16000 */ -}; - -#endif /* _LINUX_MAX6639_H */ -- 2.37.3