Hello,
sob., 20 sie 2022 o 00:26 Chris Morgan <macroalpha82@xxxxxxxxx> napisał(a):
>
> From: Chris Morgan <macromorgan@xxxxxxxxxxx>
>
> Anbernic RG353P and RG503 are both RK3566 based handheld gaming devices
> from Anbernic.
>
> Both devices have:
> - 2 SDMMC slots.
> - A Realtek rtl8821cs WiFi/Bluetooth adapter.
> - A mini HDMI port.
> - A USB C host port and a USB C otg port (currently only working as
> device).
> - Multiple GPIO buttons and a single ADC button.
> - Dual analog joysticks controlled via a GPIO mux.
> - A headphone jack with amplified stereo speakers via a SGM4865 amp.
> - A PWM based vibrator for force feedback.
>
> The RG353P has:
> - 2GB LPDDR4 RAM.
> - A 32GB eMMC.
> - A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c
> controlled touchscreen (touchscreen is a Hynitron CST340).
>
> The RG503 has:
> - 1GB LPDDR4 RAM.
> - A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung
> with part number ams495qa04. Data for this panel is provided via the
> DSI interface, however commands are sent via a 9-bit 3-wire SPI
> interface. The MISO pin of SPI3 of the SOC is wired to the input of
> the panel, so it must be bitbanged.
>
> This devicetree enables the following hardware:
> - HDMI (plus audio).
> - Analog audio, including speakers.
> - All buttons.
> - All SDMMC/eMMC/SDIO controllers.
> - The ADC joysticks (note a pending patch is required to use them).
> - WiFi/Bluetooth (note out of tree drivers are required).
> - The PWM based vibrator motor.
>
> The following hardware is not enabled:
> - The display panels (drivers are being written and there are issues
> with the upstream DSI and VOP2 subsystems).
> - Battery (driver pending).
> - Touchscreen on the RG353P (note the i2c2 bus is enabled for it).
>
> Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 2 +
> .../dts/rockchip/rk3566-anbernic-rg353p.dts | 103 +++
> .../dts/rockchip/rk3566-anbernic-rg503.dts | 93 ++
> .../dts/rockchip/rk3566-anbernic-rgxx3.dtsi | 821 ++++++++++++++++++
> 4 files changed, 1019 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index ef79a672804a..1402274a78a0 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -57,6 +57,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rockpro64.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353p.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
> new file mode 100644
> index 000000000000..f9333ed1ecc7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
> @@ -0,0 +1,103 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3566-anbernic-rgxx3.dtsi"
> +
> +/ {
> + model = "RG353P";
> + compatible = "anbernic,rg353p", "rockchip,rk3566";
> +
> + aliases {
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc0;
> + mmc2 = &sdmmc1;
> + mmc3 = &sdmmc2;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + power-supply = <&vcc_sys>;
> + pwms = <&pwm4 0 25000 0>;
> + };
> +};
> +
> +&gpio_keys_control {
> + button-5 {
> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "DPAD-LEFT";
> + linux,code = <BTN_DPAD_RIGHT>;
> + };
> +
> + button-6 {
> + gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "DPAD-RIGHT";
> + linux,code = <BTN_DPAD_LEFT>;
> + };
> +
> + button-9 {
> + gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
> + label = "TR";
> + linux,code = <BTN_TR2>;
> + };
> +
> + button-10 {
> + gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
> + label = "TR2";
> + linux,code = <BTN_TR>;
> + };
> +
> + button-14 {
> + gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
> + label = "WEST";
> + linux,code = <BTN_WEST>;
> + };
> +
> + button-15 {
I don't think just having the buttons numbered sequentially
is the best course of action, but this preserves the GPIO
ordering while other options don't...
I'm thinking about either having them named after
their function, or named after what they're labeled
on the PCB of the device.
Can any of DT maintainers give their input on this?
> + gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
> + label = "EAST";
> + linux,code = <BTN_EAST>;
> + };
> +};
> +
> +&i2c0 {
> + /* This hardware is physically present but unused. */
> + cw2015@62 {
> + compatible = "cellwise,cw2015";
> + reg = <0x62>;
> + status = "disabled";
> + };
> +};
> +
> +&i2c2 {
> + pintctrl-names = "default";
> + pinctrl-0 = <&i2c2m1_xfer>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + gpio-lcd {
> + lcd_rst: lcd-rst {
> + rockchip,pins =
> + <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
Is it unused? If it is I think it would belong to patch that would add
panel to this device
> + };
> +};
> +
> +&pwm4 {
> + status = "okay";
> +};
> +
> +&sdhci {
> + pinctrl-0 = <&emmc_bus8>, <&emmc_clk>, <&emmc_cmd>, <&emmc_datastrobe>, <&emmc_rstnout>;
> + pinctrl-names = "default";
> + bus-width = <8>;
> + mmc-hs200-1_8v;
> + non-removable;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
> new file mode 100644
> index 000000000000..8effda100b26
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
> @@ -0,0 +1,93 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3566-anbernic-rgxx3.dtsi"
> +
> +/ {
> + model = "RG503";
> + compatible = "anbernic,rg503", "rockchip,rk3566";
> +
> + aliases {
> + mmc0 = &sdmmc0;
> + mmc1 = &sdmmc1;
> + mmc2 = &sdmmc2;
> + };
> +
> + gpio_spi: spi {
> + compatible = "spi-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_pins>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sck-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
> + mosi-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
> + cs-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
> + num-chipselects = <0>;
> + };
> +};
> +
> +&gpio_keys_control {
> + button-5 {
> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "DPAD-LEFT";
> + linux,code = <BTN_DPAD_LEFT>;
> + };
> +
> + button-6 {
> + gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "DPAD-RIGHT";
> + linux,code = <BTN_DPAD_RIGHT>;
> + };
> +
> + button-9 {
> + gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
> + label = "TR";
> + linux,code = <BTN_TR>;
> + };
> +
> + button-10 {
> + gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
> + label = "TR2";
> + linux,code = <BTN_TR2>;
> + };
> +
> + button-14 {
> + gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
> + label = "EAST";
> + linux,code = <BTN_EAST>;
> + };
> +
> + button-15 {
> + gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
> + label = "WEST";
> + linux,code = <BTN_WEST>;
> + };
> +};
> +
> +&pinctrl {
> + gpio-spi {
> + spi_pins: spi-pins {
> + rockchip,pins =
> + <4 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>,
> + <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
> + <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + gpio-lcd {
> + lcd_enable: lcd-enable {
> + rockchip,pins =
> + <4 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + lcd_reset: lcd-reset {
> + rockchip,pins =
> + <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
Same comment as above to the LCD pins on RG353P
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
> new file mode 100644
> index 000000000000..7fbbee2fad8e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
> @@ -0,0 +1,821 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3566.dtsi"
> +
> +/ {
> + chosen: chosen {
> + stdout-path = "serial2:1500000n8";
I'm wondering if this should be changed to 115200 baud rate
so it would end up the same as on other devices,
like Odroid Go Advance.
> + };
> +
> + adc-joystick {
> + compatible = "adc-joystick";
> + io-channels = <&adc_mux 0>,
> + <&adc_mux 1>,
> + <&adc_mux 2>,
> + <&adc_mux 3>;
> + pinctrl-0 = <&joy_mux_en>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + axis@0 {
> + reg = <0>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <1023 15>;
> + linux,code = <ABS_X>;
> + };
> +
> + axis@1 {
> + reg = <1>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <15 1023>;
> + linux,code = <ABS_RX>;
> + };
> +
> + axis@2 {
> + reg = <2>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <15 1023>;
> + linux,code = <ABS_Y>;
> + };
> +
> + axis@3 {
> + reg = <3>;
> + abs-flat = <32>;
> + abs-fuzz = <32>;
> + abs-range = <1023 15>;
> + linux,code = <ABS_RY>;
> + };
> + };
> +
> + adc_keys: adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <60>;
> +
> + /*
> + * Button is mapped to F key in BSP kernel, but
> + * according to input guidelines it should be mode.
> + */
> + button-mode {
> + label = "MODE";
The physical button is labeled "F", so maybe this should be "F"
too?
Best Regards,
Maya Matuszczyk
> + linux,code = <BTN_MODE>;
> + press-threshold-microvolt = <1750>;
> + };
> + };
> +
> + adc_mux: adc-mux {
> + compatible = "io-channel-mux";
> + channels = "left_x", "right_x", "left_y", "right_y";
> + #io-channel-cells = <1>;
> + io-channels = <&saradc 3>;
> + io-channel-names = "parent";
> + mux-controls = <&gpio_mux>;
> + settle-time-us = <100>;
> + };
> +
> + gpio_keys_control: gpio-keys-control {
> + compatible = "gpio-keys";
> + pinctrl-0 = <&btn_pins_ctrl>;
> + pinctrl-names = "default";
> +
> + button-1 {
> + gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>;
> + label = "THUMBL";
> + linux,code = <BTN_THUMBL>;
> + };
> +
> + button-2 {
> + gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
> + label = "THUMBR";
> + linux,code = <BTN_THUMBR>;
> + };
> +
> + button-3 {
> + gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
> + label = "DPAD-UP";
> + linux,code = <BTN_DPAD_UP>;
> + };
> +
> + button-4 {
> + gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
> + label = "DPAD-DOWN";
> + linux,code = <BTN_DPAD_DOWN>;
> + };
> +
> + button-7 {
> + gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>;
> + label = "TL";
> + linux,code = <BTN_TL>;
> + };
> +
> + button-8 {
> + gpios = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
> + label = "TL2";
> + linux,code = <BTN_TL2>;
> + };
> +
> + button-11 {
> + gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_LOW>;
> + label = "START";
> + linux,code = <BTN_START>;
> + };
> +
> + button-12 {
> + gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>;
> + label = "SELECT";
> + linux,code = <BTN_SELECT>;
> + };
> +
> + button-13 {
> + gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
> + label = "NORTH";
> + linux,code = <BTN_NORTH>;
> + };
> +
> + button-16 {
> + gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_LOW>;
> + label = "SOUTH";
> + linux,code = <BTN_SOUTH>;
> + };
> + };
> +
> + gpio_keys_vol: gpio-keys-vol {
> + compatible = "gpio-keys";
> + autorepeat;
> + pinctrl-0 = <&btn_pins_vol>;
> + pinctrl-names = "default";
> +
> + button-vol-down {
> + gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
> + label = "VOLUMEDOWN";
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +
> + button-vol-up {
> + gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
> + label = "VOLUMEUP";
> + linux,code = <KEY_VOLUMEUP>;
> + };
> + };
> +
> + gpio_mux: mux-controller {
> + compatible = "gpio-mux";
> + mux-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>,
> + <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>;
> + #mux-control-cells = <0>;
> + };
> +
> + hdmi-con {
> + compatible = "hdmi-connector";
> + type = "c";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds: gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&led_pins>;
> + pinctrl-names = "default";
> +
> + green_led: led-0 {
> + color = <LED_COLOR_ID_GREEN>;
> + default-state = "on";
> + function = LED_FUNCTION_POWER;
> + gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
> + };
> +
> + amber_led: led-1 {
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_CHARGING;
> + gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> + retain-state-suspended;
> + };
> +
> + red_led: led-2 {
> + color = <LED_COLOR_ID_RED>;
> + default-state = "off";
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + /* Channels reversed for both headphones and speakers. */
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "anbernic_rk817";
> + simple-audio-card,aux-devs = <&spk_amp>;
> + simple-audio-card,format = "i2s";
> + simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones",
> + "Speaker", "Internal Speakers";
> + simple-audio-card,routing =
> + "MICL", "Mic Jack",
> + "Headphones", "HPOL",
> + "Headphones", "HPOR",
> + "Internal Speakers", "Speaker Amp OUTL",
> + "Internal Speakers", "Speaker Amp OUTR",
> + "Speaker Amp INL", "HPOL",
> + "Speaker Amp INR", "HPOR";
> + simple-audio-card,pin-switches = "Internal Speakers";
> +
> + simple-audio-card,codec {
> + sound-dai = <&rk817>;
> + };
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1_8ch>;
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk817 1>;
> + clock-names = "ext_clock";
> + pinctrl-0 = <&wifi_enable_h>;
> + pinctrl-names = "default";
> + post-power-on-delay-ms = <200>;
> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_LOW>;
> + };
> +
> + spk_amp: audio-amplifier {
> + compatible = "simple-audio-amplifier";
> + enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&spk_amp_enable_h>;
> + pinctrl-names = "default";
> + sound-name-prefix = "Speaker Amp";
> + };
> +
> + vcc3v3_lcd0_n: regulator-vcc3v3-lcd0 {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + pinctrl-0 = <&vcc_lcd_h>;
> + pinctrl-names = "default";
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_lcd0_n";
> + vin-supply = <&vcc_3v3>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_sys: regulator-vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3800000>;
> + regulator-max-microvolt = <3800000>;
> + regulator-name = "vcc_sys";
> + };
> +
> + vcc_wifi: regulator-vcc-wifi {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&vcc_wifi_h>;
> + pinctrl-names = "default";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_wifi";
> + };
> +
> + vibrator: pwm-vibrator {
> + compatible = "pwm-vibrator";
> + pwm-names = "enable";
> + pwms = <&pwm5 0 1000000000 0>;
> + };
> +};
> +
> +&combphy1 {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&hdmi_in {
> + hdmi_in_vp0: endpoint {
> + remote-endpoint = <&vp0_out_hdmi>;
> + };
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + rk817: pmic@20 {
> + compatible = "rockchip,rk817";
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> + clock-output-names = "rk808-clkout1", "rk808-clkout2";
> + clock-names = "mclk";
> + clocks = <&cru I2S1_MCLKOUT_TX>;
> + assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> + #clock-cells = <1>;
> + #sound-dai-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s1m0_mclk>, <&pmic_int_l>;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc5-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_sys>;
> + vcc9-supply = <&dcdc_boost>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-init-microvolt = <900000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_logic";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <900000>;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-init-microvolt = <900000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_gpu";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_3v3: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc_3v3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcca1v8_pmu: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcca1v8_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdda_0v9: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda_0v9";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdda0v9_pmu: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda0v9_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <900000>;
> + };
> + };
> +
> + vccio_acodec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_acodec";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_pmu: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_1v8: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc1v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc2v8_dvp: LDO_REG9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-name = "vcc2v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + dcdc_boost: BOOST {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <4700000>;
> + regulator-max-microvolt = <5400000>;
> + regulator-name = "boost";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + otg_switch: OTG_SWITCH {
> + regulator-name = "otg_switch";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +
> + vdd_cpu: regulator@40 {
> + compatible = "fcs,fan53555";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1390000>;
> + regulator-init-microvolt = <900000>;
> + regulator-name = "vdd_cpu";
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc_sys>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c1 {
> + /* Unknown/unused device at 0x3c */
> + status = "disabled";
> +};
> +
> +&i2s0_8ch {
> + status = "okay";
> +};
> +
> +&i2s1_8ch {
> + pinctrl-0 = <&i2s1m0_sclktx
> + &i2s1m0_lrcktx
> + &i2s1m0_sdi0
> + &i2s1m0_sdo0>;
> + pinctrl-names = "default";
> + rockchip,trcm-sync-tx-only;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + audio-amplifier {
> + spk_amp_enable_h: spk-amp-enable-h {
> + rockchip,pins =
> + <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + gpio-btns {
> + btn_pins_ctrl: btn-pins-ctrl {
> + rockchip,pins =
> + <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + btn_pins_vol: btn-pins-vol {
> + rockchip,pins =
> + <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
> + <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + gpio-led {
> + led_pins: led-pins {
> + rockchip,pins =
> + <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>,
> + <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
> + <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + joy-mux {
> + joy_mux_en: joy-mux-en {
> + rockchip,pins =
> + <0 RK_PB5 RK_FUNC_GPIO &pcfg_output_low>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins =
> + <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins =
> + <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + vcc3v3-lcd {
> + vcc_lcd_h: vcc-lcd-h {
> + rockchip,pins =
> + <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + vcc-wifi {
> + vcc_wifi_h: vcc-wifi-h {
> + rockchip,pins =
> + <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pmu_io_domains {
> + status = "okay";
> + pmuio1-supply = <&vcc3v3_pmu>;
> + pmuio2-supply = <&vcc3v3_pmu>;
> + vccio1-supply = <&vccio_acodec>;
> + vccio3-supply = <&vccio_sd>;
> + vccio4-supply = <&vcc_1v8>;
> + vccio5-supply = <&vcc_3v3>;
> + vccio6-supply = <&vcc1v8_dvp>;
> + vccio7-supply = <&vcc_3v3>;
> +};
> +
> +&pwm5 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> + pinctrl-names = "default";
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&sdmmc1 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &sdmmc1_det>;
> + pinctrl-names = "default";
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc1v8_dvp>;
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
> + pinctrl-names = "default";
> + vmmc-supply = <&vcc_wifi>;
> + vqmmc-supply = <&vcca1v8_pmu>;
> + status = "okay";
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>;
> + rockchip,hw-tshut-polarity = <0>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-0 = <&uart1m1_xfer &uart1m1_ctsn &uart1m1_rtsn>;
> + pinctrl-names = "default";
> + uart-has-rtscts;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "realtek,rtl8821cs-bt";
> + device-wake-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
> + enable-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
> + host-wake-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +/*
> + * Lack the schematics to verify, but port works as a peripheral
> + * (and not a host or OTG port).
> + */
> +&usb_host0_xhci {
> + dr_mode = "peripheral";
> + phys = <&usb2phy0_otg>;
> + phy-names = "usb2-phy";
> + status = "okay";
> +};
> +
> +&usb_host1_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1_ohci {
> + status = "okay";
> +};
> +
> +&usb_host1_xhci {
> + phy-names = "usb2-phy", "usb3-phy";
> + phys = <&usb2phy1_host>, <&combphy1 PHY_TYPE_USB3>;
> + status = "okay";
> +};
> +
> +&usb2phy0 {
> + status = "okay";
> +};
> +
> +&usb2phy0_otg {
> + status = "okay";
> +};
> +
> +&usb2phy1 {
> + status = "okay";
> +};
> +
> +&usb2phy1_host {
> + status = "okay";
> +};
> +
> +&vop {
> + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
> + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
> + status = "okay";
> +};
> +
> +&vop_mmu {
> + status = "okay";
> +};
> +
> +&vp0 {
> + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
> + reg = <ROCKCHIP_VOP2_EP_HDMI0>;
> + remote-endpoint = <&hdmi_in_vp0>;
> + };
> +};
> --
> 2.25.1
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
