From: Chris Morgan <macromorgan@xxxxxxxxxxx>
Anbernic RG353P and RG503 are both RK3566 based handheld gaming devices
from Anbernic.
Both devices have:
- 2 SDMMC slots.
- A Realtek rtl8821cs WiFi/Bluetooth adapter.
- A mini HDMI port.
- A USB C host port and a USB C otg port (currently only working as
device).
- Multiple GPIO buttons and a single ADC button.
- Dual analog joysticks controlled via a GPIO mux.
- A headphone jack with amplified stereo speakers via a SGM4865 amp.
- A PWM based vibrator for force feedback.
The RG353P has:
- 2GB LPDDR4 RAM.
- A 32GB eMMC.
- A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c
controlled touchscreen (touchscreen is a Hynitron CST340).
The RG503 has:
- 1GB LPDDR4 RAM.
- A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung
with part number ams495qa04. Data for this panel is provided via the
DSI interface, however commands are sent via a 9-bit 3-wire SPI
interface. The MISO pin of SPI3 of the SOC is wired to the input of
the panel, so it must be bitbanged.
This devicetree enables the following hardware:
- HDMI (plus audio).
- Analog audio, including speakers.
- All buttons.
- All SDMMC/eMMC/SDIO controllers.
- The ADC joysticks (note a pending patch is required to use them).
- WiFi/Bluetooth (note out of tree drivers are required).
- The PWM based vibrator motor.
The following hardware is not enabled:
- The display panels (drivers are being written and there are issues
with the upstream DSI and VOP2 subsystems).
- Battery (driver pending).
- Touchscreen on the RG353P (note the i2c2 bus is enabled for it).
Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
---
arch/arm64/boot/dts/rockchip/Makefile | 2 +
.../dts/rockchip/rk3566-anbernic-rg353p.dts | 103 +++
.../dts/rockchip/rk3566-anbernic-rg503.dts | 93 ++
.../dts/rockchip/rk3566-anbernic-rgxx3.dtsi | 821 ++++++++++++++++++
4 files changed, 1019 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ef79a672804a..1402274a78a0 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -57,6 +57,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rockpro64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353p.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
new file mode 100644
index 000000000000..f9333ed1ecc7
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3566-anbernic-rgxx3.dtsi"
+
+/ {
+ model = "RG353P";
+ compatible = "anbernic,rg353p", "rockchip,rk3566";
+
+ aliases {
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc0;
+ mmc2 = &sdmmc1;
+ mmc3 = &sdmmc2;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&vcc_sys>;
+ pwms = <&pwm4 0 25000 0>;
+ };
+};
+
+&gpio_keys_control {
+ button-5 {
+ gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ };
+
+ button-6 {
+ gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_LEFT>;
+ };
+
+ button-9 {
+ gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
+ label = "TR";
+ linux,code = <BTN_TR2>;
+ };
+
+ button-10 {
+ gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
+ label = "TR2";
+ linux,code = <BTN_TR>;
+ };
+
+ button-14 {
+ gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
+ label = "WEST";
+ linux,code = <BTN_WEST>;
+ };
+
+ button-15 {
+ gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+ label = "EAST";
+ linux,code = <BTN_EAST>;
+ };
+};
+
+&i2c0 {
+ /* This hardware is physically present but unused. */
+ cw2015@62 {
+ compatible = "cellwise,cw2015";
+ reg = <0x62>;
+ status = "disabled";
+ };
+};
+
+&i2c2 {
+ pintctrl-names = "default";
+ pinctrl-0 = <&i2c2m1_xfer>;
+ status = "okay";
+};
+
+&pinctrl {
+ gpio-lcd {
+ lcd_rst: lcd-rst {
+ rockchip,pins =
+ <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+&sdhci {
+ pinctrl-0 = <&emmc_bus8>, <&emmc_clk>, <&emmc_cmd>, <&emmc_datastrobe>, <&emmc_rstnout>;
+ pinctrl-names = "default";
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
new file mode 100644
index 000000000000..8effda100b26
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3566-anbernic-rgxx3.dtsi"
+
+/ {
+ model = "RG503";
+ compatible = "anbernic,rg503", "rockchip,rk3566";
+
+ aliases {
+ mmc0 = &sdmmc0;
+ mmc1 = &sdmmc1;
+ mmc2 = &sdmmc2;
+ };
+
+ gpio_spi: spi {
+ compatible = "spi-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_pins>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <0>;
+ };
+};
+
+&gpio_keys_control {
+ button-5 {
+ gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ };
+
+ button-6 {
+ gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ };
+
+ button-9 {
+ gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
+ label = "TR";
+ linux,code = <BTN_TR>;
+ };
+
+ button-10 {
+ gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
+ label = "TR2";
+ linux,code = <BTN_TR2>;
+ };
+
+ button-14 {
+ gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
+ label = "EAST";
+ linux,code = <BTN_EAST>;
+ };
+
+ button-15 {
+ gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+ label = "WEST";
+ linux,code = <BTN_WEST>;
+ };
+};
+
+&pinctrl {
+ gpio-spi {
+ spi_pins: spi-pins {
+ rockchip,pins =
+ <4 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>,
+ <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
+ <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ gpio-lcd {
+ lcd_enable: lcd-enable {
+ rockchip,pins =
+ <4 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ lcd_reset: lcd-reset {
+ rockchip,pins =
+ <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
new file mode 100644
index 000000000000..7fbbee2fad8e
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
@@ -0,0 +1,821 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ adc-joystick {
+ compatible = "adc-joystick";
+ io-channels = <&adc_mux 0>,
+ <&adc_mux 1>,
+ <&adc_mux 2>,
+ <&adc_mux 3>;
+ pinctrl-0 = <&joy_mux_en>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <1023 15>;
+ linux,code = <ABS_X>;
+ };
+
+ axis@1 {
+ reg = <1>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <15 1023>;
+ linux,code = <ABS_RX>;
+ };
+
+ axis@2 {
+ reg = <2>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <15 1023>;
+ linux,code = <ABS_Y>;
+ };
+
+ axis@3 {
+ reg = <3>;
+ abs-flat = <32>;
+ abs-fuzz = <32>;
+ abs-range = <1023 15>;
+ linux,code = <ABS_RY>;
+ };
+ };
+
+ adc_keys: adc-keys {
+ compatible = "adc-keys";
+ io-channels = <&saradc 0>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+ poll-interval = <60>;
+
+ /*
+ * Button is mapped to F key in BSP kernel, but
+ * according to input guidelines it should be mode.
+ */
+ button-mode {
+ label = "MODE";
+ linux,code = <BTN_MODE>;
+ press-threshold-microvolt = <1750>;
+ };
+ };
+
+ adc_mux: adc-mux {
+ compatible = "io-channel-mux";
+ channels = "left_x", "right_x", "left_y", "right_y";
+ #io-channel-cells = <1>;
+ io-channels = <&saradc 3>;
+ io-channel-names = "parent";
+ mux-controls = <&gpio_mux>;
+ settle-time-us = <100>;
+ };
+
+ gpio_keys_control: gpio-keys-control {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&btn_pins_ctrl>;
+ pinctrl-names = "default";
+
+ button-1 {
+ gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>;
+ label = "THUMBL";
+ linux,code = <BTN_THUMBL>;
+ };
+
+ button-2 {
+ gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
+ label = "THUMBR";
+ linux,code = <BTN_THUMBR>;
+ };
+
+ button-3 {
+ gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ };
+
+ button-4 {
+ gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ };
+
+ button-7 {
+ gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>;
+ label = "TL";
+ linux,code = <BTN_TL>;
+ };
+
+ button-8 {
+ gpios = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
+ label = "TL2";
+ linux,code = <BTN_TL2>;
+ };
+
+ button-11 {
+ gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_LOW>;
+ label = "START";
+ linux,code = <BTN_START>;
+ };
+
+ button-12 {
+ gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>;
+ label = "SELECT";
+ linux,code = <BTN_SELECT>;
+ };
+
+ button-13 {
+ gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+ label = "NORTH";
+ linux,code = <BTN_NORTH>;
+ };
+
+ button-16 {
+ gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_LOW>;
+ label = "SOUTH";
+ linux,code = <BTN_SOUTH>;
+ };
+ };
+
+ gpio_keys_vol: gpio-keys-vol {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-0 = <&btn_pins_vol>;
+ pinctrl-names = "default";
+
+ button-vol-down {
+ gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ label = "VOLUMEDOWN";
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ button-vol-up {
+ gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
+ label = "VOLUMEUP";
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ gpio_mux: mux-controller {
+ compatible = "gpio-mux";
+ mux-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>,
+ <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>;
+ #mux-control-cells = <0>;
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "c";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ green_led: led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+ };
+
+ amber_led: led-1 {
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_CHARGING;
+ gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ retain-state-suspended;
+ };
+
+ red_led: led-2 {
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ /* Channels reversed for both headphones and speakers. */
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "anbernic_rk817";
+ simple-audio-card,aux-devs = <&spk_amp>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Internal Speakers";
+ simple-audio-card,routing =
+ "MICL", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Internal Speakers", "Speaker Amp OUTL",
+ "Internal Speakers", "Speaker Amp OUTR",
+ "Speaker Amp INL", "HPOL",
+ "Speaker Amp INR", "HPOR";
+ simple-audio-card,pin-switches = "Internal Speakers";
+
+ simple-audio-card,codec {
+ sound-dai = <&rk817>;
+ };
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk817 1>;
+ clock-names = "ext_clock";
+ pinctrl-0 = <&wifi_enable_h>;
+ pinctrl-names = "default";
+ post-power-on-delay-ms = <200>;
+ reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_LOW>;
+ };
+
+ spk_amp: audio-amplifier {
+ compatible = "simple-audio-amplifier";
+ enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&spk_amp_enable_h>;
+ pinctrl-names = "default";
+ sound-name-prefix = "Speaker Amp";
+ };
+
+ vcc3v3_lcd0_n: regulator-vcc3v3-lcd0 {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ pinctrl-0 = <&vcc_lcd_h>;
+ pinctrl-names = "default";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_lcd0_n";
+ vin-supply = <&vcc_3v3>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_sys: regulator-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-name = "vcc_sys";
+ };
+
+ vcc_wifi: regulator-vcc-wifi {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&vcc_wifi_h>;
+ pinctrl-names = "default";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_wifi";
+ };
+
+ vibrator: pwm-vibrator {
+ compatible = "pwm-vibrator";
+ pwm-names = "enable";
+ pwms = <&pwm5 0 1000000000 0>;
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_mclk>, <&pmic_int_l>;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_sys>;
+ vcc9-supply = <&dcdc_boost>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_logic";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_3v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda_0v9";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_acodec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc1v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc2v8_dvp: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc2v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ dcdc_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <4700000>;
+ regulator-max-microvolt = <5400000>;
+ regulator-name = "boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ otg_switch: OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu: regulator@40 {
+ compatible = "fcs,fan53555";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1390000>;
+ regulator-init-microvolt = <900000>;
+ regulator-name = "vdd_cpu";
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc_sys>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c1 {
+ /* Unknown/unused device at 0x3c */
+ status = "disabled";
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ pinctrl-names = "default";
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&pinctrl {
+ audio-amplifier {
+ spk_amp_enable_h: spk-amp-enable-h {
+ rockchip,pins =
+ <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ gpio-btns {
+ btn_pins_ctrl: btn-pins-ctrl {
+ rockchip,pins =
+ <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ btn_pins_vol: btn-pins-vol {
+ rockchip,pins =
+ <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
+ <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ gpio-led {
+ led_pins: led-pins {
+ rockchip,pins =
+ <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>,
+ <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
+ <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ joy-mux {
+ joy_mux_en: joy-mux-en {
+ rockchip,pins =
+ <0 RK_PB5 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins =
+ <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins =
+ <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ vcc3v3-lcd {
+ vcc_lcd_h: vcc-lcd-h {
+ rockchip,pins =
+ <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ vcc-wifi {
+ vcc_wifi_h: vcc-wifi-h {
+ rockchip,pins =
+ <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ status = "okay";
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc1v8_dvp>;
+ vccio7-supply = <&vcc_3v3>;
+};
+
+&pwm5 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ pinctrl-names = "default";
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &sdmmc1_det>;
+ pinctrl-names = "default";
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc1v8_dvp>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vcc_wifi>;
+ vqmmc-supply = <&vcca1v8_pmu>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1m1_xfer &uart1m1_ctsn &uart1m1_rtsn>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8821cs-bt";
+ device-wake-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ host-wake-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart2 {
+ status = "okay";
+};
+
+/*
+ * Lack the schematics to verify, but port works as a peripheral
+ * (and not a host or OTG port).
+ */
+&usb_host0_xhci {
+ dr_mode = "peripheral";
+ phys = <&usb2phy0_otg>;
+ phy-names = "usb2-phy";
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ phy-names = "usb2-phy", "usb3-phy";
+ phys = <&usb2phy1_host>, <&combphy1 PHY_TYPE_USB3>;
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.25.1
