From: René Moll <linux@xxxxxxxxx>
The LTC2952 allows control over system power using a push button. It also
supports powering down the board from a controller on the board.
If the power button is pushed, the ltc2952 starts a 400ms window to
properly shut down the software. This window can be stretched by
toggling a watchdog line. This driver always uses this watchdog line.
The power button input is optional. This allows the system to use a
custom shutdown sequence on the push button.
On software shutdown the driver sets the kill signal, starting the same
sequence as if the push button was used.
Signed-off-by: Ren�oll <linux@xxxxxxxxx>
Signed-off-by: Tjerk Hofmeijer <tjerk.hofmeijer@xxxxxxxxx>
Signed-off-by: Frans Klaver <frans.klaver@xxxxxxxxx>
---
drivers/power/reset/Kconfig | 10 +
drivers/power/reset/Makefile | 1 +
drivers/power/reset/ltc2952-poweroff.c | 381 +++++++++++++++++++++++++++++++++
3 files changed, 392 insertions(+)
create mode 100644 drivers/power/reset/ltc2952-poweroff.c
diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
index ca41523..a0f68da 100644
--- a/drivers/power/reset/Kconfig
+++ b/drivers/power/reset/Kconfig
@@ -45,6 +45,16 @@ config POWER_RESET_HISI
help
Reboot support for Hisilicon boards.
+config POWER_RESET_LTC2952
+ bool "LTC2952 PowerPath power-off driver"
+ depends on OF_GPIO && POWER_RESET
+ help
+ This driver supports an external powerdown trigger and board
+ power down via the LTC2952.
+
+ If your board uses an LTC2952, say Y and create a binding
+ in the device tree.
+
config POWER_RESET_MSM
bool "Qualcomm MSM power-off driver"
depends on POWER_RESET && ARCH_QCOM
diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile
index a42e70e..3cbb7c3 100644
--- a/drivers/power/reset/Makefile
+++ b/drivers/power/reset/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_POWER_RESET_AXXIA) += axxia-reset.o
obj-$(CONFIG_POWER_RESET_BRCMSTB) += brcmstb-reboot.o
obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o
obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o
+obj-$(CONFIG_POWER_RESET_LTC2952) += ltc2952-poweroff.o
obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o
obj-$(CONFIG_POWER_RESET_QNAP) += qnap-poweroff.o
obj-$(CONFIG_POWER_RESET_RESTART) += restart-poweroff.o
diff --git a/drivers/power/reset/ltc2952-poweroff.c b/drivers/power/reset/ltc2952-poweroff.c
new file mode 100644
index 0000000..2cf146a
--- /dev/null
+++ b/drivers/power/reset/ltc2952-poweroff.c
@@ -0,0 +1,381 @@
+/*
+ * LTC2952 PowerPath TM driver
+ *
+ * Copyright (C) 2014, Xsens Technologies BV <info@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * ----------------------------------------
+ * - Description
+ * ----------------------------------------
+ *
+ * This driver is to be used with an external LTC2952 PowerPath Controller.
+ * Its function is to determine when a external shut down is triggered
+ * and react by properly shutting down the system.
+ *
+ * This driver expects a device tree with a ltc2952 entry for pin mapping.
+ *
+ * ----------------------------------------
+ * - GPIO
+ * ----------------------------------------
+ *
+ * The following GPIOs are used:
+ * - trigger (input, optional)
+ * A level change indicates the shut-down trigger. If it's state reverts
+ * within the time-out defined by trigger_delay, the shut down is not
+ * executed. If no pin is assigned to this input the driver will start
+ * the watchdog immediately and only a power off event will kill the ltc2952
+ *
+ * - watchdog (output)
+ * Once a shut down is triggered, the driver will toggle this signal,
+ * with an internal (wde_interval) to stall the hardware shut down.
+ *
+ * - kill (output)
+ * The last action during shut down is triggering this signalling, such
+ * that the PowerPath Control will power down the hardware.
+ *
+ * ----------------------------------------
+ * - Interrupts
+ * ----------------------------------------
+ *
+ * The driver requires a non-shared, edge-triggered interrupt on the trigger
+ * GPIO.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/ktime.h>
+#include <linux/slab.h>
+#include <linux/kmod.h>
+#include <linux/module.h>
+#include <linux/gpio/consumer.h>
+#include <linux/reboot.h>
+
+struct ltc2952_poweroff_data {
+ struct hrtimer timer_trigger;
+ struct hrtimer timer_wde;
+
+ ktime_t trigger_delay;
+ ktime_t wde_interval;
+
+ struct device *dev;
+
+ unsigned int virq;
+
+ struct gpio_desc *gpio_trigger;
+ struct gpio_desc *gpio_watchdog;
+ struct gpio_desc *gpio_kill;
+};
+
+static bool ltc2952_poweroff_panic;
+static struct ltc2952_poweroff_data *ltc2952_data;
+
+/**
+ * ltc2952_poweroff_timer_wde - Timer callback
+ * Toggles the watchdog reset signal each wde_interval
+ *
+ * @timer: corresponding timer
+ *
+ * Returns HRTIMER_RESTART for an infinite loop which will only stop when the
+ * machine actually shuts down
+ */
+static enum hrtimer_restart ltc2952_poweroff_timer_wde(struct hrtimer *timer)
+{
+ ktime_t now;
+ int state;
+ unsigned long overruns;
+
+ if (ltc2952_poweroff_panic)
+ return HRTIMER_NORESTART;
+
+ state = gpiod_get_value(ltc2952_data->gpio_watchdog);
+ gpiod_set_value(ltc2952_data->gpio_watchdog, !state);
+
+ now = hrtimer_cb_get_time(timer);
+ overruns = hrtimer_forward(timer, now, ltc2952_data->wde_interval);
+
+ return HRTIMER_RESTART;
+}
+
+static void ltc2952_poweroff_start_wde(void)
+{
+ int ret;
+
+ ret = hrtimer_start(<c2952_data->timer_wde,
+ ltc2952_data->wde_interval, HRTIMER_MODE_REL);
+
+ if (ret) {
+ dev_err(ltc2952_data->dev,
+ "unable to start the watchdog timer\n");
+ /*
+ * The device will not toggle the watchdog reset,
+ * thus shut down is only safe if the PowerPath controller
+ * has a long enough time-off before triggering a hardware
+ * power-off.
+ *
+ * Only sending a warning as the system will power-off anyway
+ */
+ }
+}
+
+static enum hrtimer_restart ltc2952_poweroff_timer_trigger(struct hrtimer *t)
+{
+ ltc2952_poweroff_start_wde();
+
+ dev_info(ltc2952_data->dev, "executing shutdown\n");
+
+ orderly_poweroff(true);
+
+ return HRTIMER_NORESTART;
+}
+
+/**
+ * ltc2952_poweroff_handler - Interrupt handler
+ * Triggered each time the trigger signal changes state and (de)activates a
+ * time-out (timer_trigger). Once the time-out is actually reached the shut
+ * down is executed.
+ *
+ * @irq: IRQ number
+ * @dev_id: pointer to the main data structure
+ */
+static irqreturn_t ltc2952_poweroff_handler(int irq, void *dev_id)
+{
+ struct ltc2952_poweroff_data *data = dev_id;
+
+ if (ltc2952_poweroff_panic || hrtimer_active(&data->timer_wde))
+ /* we're either panicking, or already shutting down */
+ goto irq_ok;
+
+ if (hrtimer_active(&data->timer_trigger)) {
+ hrtimer_cancel(&data->timer_trigger);
+ goto irq_ok;
+ }
+
+ if (hrtimer_start(&data->timer_trigger, data->trigger_delay,
+ HRTIMER_MODE_REL))
+ dev_err(data->dev, "unable to start the wait timer\n");
+
+irq_ok:
+ return IRQ_HANDLED;
+}
+
+static void ltc2952_poweroff_kill(void)
+{
+ gpiod_set_value(ltc2952_data->gpio_kill, 1);
+}
+
+static int ltc2952_poweroff_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ return -ENOSYS;
+}
+
+static int ltc2952_poweroff_resume(struct platform_device *pdev)
+{
+ return -ENOSYS;
+}
+
+static void ltc2952_poweroff_default(struct ltc2952_poweroff_data *data)
+{
+ data->wde_interval = ktime_set(0, 300L*1E6L);
+ data->trigger_delay = ktime_set(2, 500L*1E6L);
+
+ hrtimer_init(&data->timer_trigger, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ data->timer_trigger.function = <c2952_poweroff_timer_trigger;
+
+ hrtimer_init(&data->timer_wde, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ data->timer_wde.function = <c2952_poweroff_timer_wde;
+}
+
+static int ltc2952_poweroff_init(struct platform_device *pdev)
+{
+ int ret;
+
+ ltc2952_poweroff_default(ltc2952_data);
+
+ ltc2952_data->gpio_watchdog = gpiod_get(&pdev->dev, "watchdog");
+ if (IS_ERR(ltc2952_data->gpio_watchdog)) {
+ ret = PTR_ERR(ltc2952_data->gpio_watchdog);
+ dev_err(&pdev->dev, "unable to claim watchdog-gpio\n");
+ goto err;
+ }
+
+ ret = gpiod_direction_output(ltc2952_data->gpio_watchdog, 0);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to use watchdog-gpio as output\n");
+ goto err_watchdog;
+ }
+
+ ltc2952_data->gpio_kill = gpiod_get(&pdev->dev, "kill");
+ if (IS_ERR(ltc2952_data->gpio_kill)) {
+ ret = PTR_ERR(ltc2952_data->gpio_kill);
+ dev_err(&pdev->dev, "unable to claim kill-gpio\n");
+ goto err_watchdog;
+ }
+
+ ret = gpiod_direction_output(ltc2952_data->gpio_kill, 0);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to use kill-gpio as output\n");
+ goto err_kill;
+ }
+
+ ltc2952_data->gpio_trigger = gpiod_get(&pdev->dev, "trigger");
+ if (IS_ERR(ltc2952_data->gpio_trigger)) {
+ ret = PTR_ERR(ltc2952_data->gpio_trigger);
+
+ if (ret != -ENOENT) {
+ dev_err(&pdev->dev, "unable to claim trigger-gpio\n");
+ goto err_kill;
+ }
+
+ dev_info(&pdev->dev, "No trigger input defined\n");
+ ltc2952_data->gpio_trigger = NULL;
+ ltc2952_poweroff_start_wde();
+ return 0;
+ }
+
+ ltc2952_data->virq = gpiod_to_irq(ltc2952_data->gpio_trigger);
+ if (ltc2952_data->virq < 0) {
+ dev_err(&pdev->dev, "cannot map GPIO as interrupt");
+ goto err_trigger;
+ }
+
+ ret = request_irq(ltc2952_data->virq,
+ ltc2952_poweroff_handler,
+ (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING),
+ "ltc2952-poweroff",
+ ltc2952_data);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot configure an interrupt handler\n");
+ goto err_trigger;
+ }
+ return 0;
+
+err_trigger:
+ gpiod_put(ltc2952_data->gpio_trigger);
+err_kill:
+ gpiod_put(ltc2952_data->gpio_kill);
+err_watchdog:
+ gpiod_put(ltc2952_data->gpio_watchdog);
+err:
+ return ret;
+}
+
+static int ltc2952_poweroff_probe(struct platform_device *pdev)
+{
+ int ret;
+
+ if (pm_power_off) {
+ dev_err(&pdev->dev, "pm_power_off already registered");
+ return -EBUSY;
+ }
+
+ ltc2952_data = kzalloc(sizeof(*ltc2952_data), GFP_KERNEL);
+ if (!ltc2952_data)
+ return -ENOMEM;
+
+ ltc2952_data->dev = &pdev->dev;
+
+ ret = ltc2952_poweroff_init(pdev);
+ if (ret)
+ goto err;
+
+ pm_power_off = <c2952_poweroff_kill;
+
+ dev_info(&pdev->dev, "probe successful\n");
+
+ return 0;
+
+err:
+ kfree(ltc2952_data);
+ return ret;
+}
+
+static int ltc2952_poweroff_remove(struct platform_device *pdev)
+{
+ pm_power_off = NULL;
+
+ if (ltc2952_data) {
+ if (ltc2952_data->gpio_trigger != NULL)
+ free_irq(ltc2952_data->virq, ltc2952_data);
+
+ if (hrtimer_active(<c2952_data->timer_wde))
+ hrtimer_cancel(<c2952_data->timer_wde);
+
+ gpiod_put(ltc2952_data->gpio_watchdog);
+ gpiod_put(ltc2952_data->gpio_kill);
+ gpiod_put(ltc2952_data->gpio_trigger);
+
+ kfree(ltc2952_data);
+ }
+
+ return 0;
+}
+
+static const struct of_device_id of_ltc2952_poweroff_match[] = {
+ { .compatible = "lltc,ltc2952"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, of_ltc2952_poweroff_match);
+
+static struct platform_driver ltc2952_poweroff_driver = {
+ .probe = ltc2952_poweroff_probe,
+ .remove = ltc2952_poweroff_remove,
+ .driver = {
+ .name = "ltc2952-poweroff",
+ .owner = THIS_MODULE,
+ .of_match_table = of_ltc2952_poweroff_match,
+ },
+ .suspend = ltc2952_poweroff_suspend,
+ .resume = ltc2952_poweroff_resume,
+};
+
+static int ltc2952_poweroff_notify_panic(struct notifier_block *nb,
+ unsigned long code,
+ void *unused)
+{
+ ltc2952_poweroff_panic = true;
+ return NOTIFY_DONE;
+}
+
+static struct notifier_block ltc2952_poweroff_panic_nb = {
+ .notifier_call = ltc2952_poweroff_notify_panic,
+};
+
+static int __init ltc2952_poweroff_platform_init(void)
+{
+ ltc2952_poweroff_panic = false;
+
+ atomic_notifier_chain_register(&panic_notifier_list,
+ <c2952_poweroff_panic_nb);
+
+ return platform_driver_register(<c2952_poweroff_driver);
+}
+
+static void __exit ltc2952_poweroff_platform_exit(void)
+{
+ atomic_notifier_chain_unregister(&panic_notifier_list,
+ <c2952_poweroff_panic_nb);
+
+ platform_driver_unregister(<c2952_poweroff_driver);
+}
+
+module_init(ltc2952_poweroff_platform_init);
+module_exit(ltc2952_poweroff_platform_exit);
+
+MODULE_AUTHOR("Ren�oll <linux@xxxxxxxxx>");
+MODULE_AUTHOR("Frans KLaver <frans.klaver@xxxxxxxxx>");
+MODULE_AUTHOR("Tjerk Hofmeijer <tjerk.hofmeijer@xxxxxxxxx>");
+MODULE_DESCRIPTION("LTC PowerPath power-off driver");
+MODULE_LICENSE("GPL v2");
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
