[PATCH 1/2] ARM: dts: qcom: ipq8064: reorganize node order and sort them

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Reorganize node order and sort them by address.

Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
---

This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next

 arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++--------------
 1 file changed, 383 insertions(+), 383 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index da90f7c08d75..cf41d330c920 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -332,19 +332,59 @@ soc: soc {
 		ranges;
 		compatible = "simple-bus";
 
-		lpass@28100000 {
-			compatible = "qcom,lpass-cpu";
-			status = "disabled";
-			clocks = <&lcc AHBIX_CLK>,
-					<&lcc MI2S_OSR_CLK>,
-					<&lcc MI2S_BIT_CLK>;
-			clock-names = "ahbix-clk",
-					"mi2s-osr-clk",
-					"mi2s-bit-clk";
-			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "lpass-irq-lpaif";
-			reg = <0x28100000 0x10000>;
-			reg-names = "lpass-lpaif";
+		stmmac_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <7>;
+			snps,rd_osr_lmt = <7>;
+			snps,blen = <16 0 0 0 0 0 0>;
+		};
+
+		vsdcc_fixed: vsdcc-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "SDCC Power";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-ipq8064";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
+		};
+
+		qcom,ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x00500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		qfprom: qfprom@700000 {
+			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			speedbin_efuse: speedbin@c0 {
+				reg = <0xc0 0x4>;
+			};
+			tsens_calib: calib@400 {
+				reg = <0x400 0xb>;
+			};
+			tsens_calib_backup: calib_backup@410 {
+				reg = <0x410 0xb>;
+			};
 		};
 
 		qcom_pinmux: pinmux@800000 {
@@ -471,6 +511,35 @@ mux {
 			};
 		};
 
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-ipq8064", "syscon";
+			clocks = <&pxo_board>, <&cxo_board>;
+			clock-names = "pxo", "cxo";
+			reg = <0x00900000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			tsens: thermal-sensor@900000 {
+				compatible = "qcom,ipq8064-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		sfpb_mutex: hwlock@1200600 {
+			compatible = "qcom,sfpb-mutex";
+			reg = <0x01200600 0x100>;
+
+			#hwlock-cells = <1>;
+		};
+
 		intc: interrupt-controller@2000000 {
 			compatible = "qcom,msm-qgic2";
 			interrupt-controller;
@@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>,
 			cpu-offset = <0x80000>;
 		};
 
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu_l2_aux";
+		};
+
 		acc0: clock-controller@2088000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
 		};
 
+		saw0: regulator@2089000 {
+			compatible = "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
 		acc1: clock-controller@2098000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
 		};
 
-		adm_dma: dma-controller@18300000 {
-			compatible = "qcom,adm";
-			reg = <0x18300000 0x100000>;
-			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
+		saw1: regulator@2099000 {
+			compatible = "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
 
-			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
-			clock-names = "core", "iface";
+		nss_common: syscon@03000000 {
+			compatible = "syscon";
+			reg = <0x03000000 0x0000FFFF>;
+		};
 
-			resets = <&gcc ADM0_RESET>,
-				 <&gcc ADM0_PBUS_RESET>,
-				 <&gcc ADM0_C0_RESET>,
-				 <&gcc ADM0_C1_RESET>,
-				 <&gcc ADM0_C2_RESET>;
-			reset-names = "clk", "pbus", "c0", "c1", "c2";
-			qcom,ee = <0>;
+		usb3_0: usb3@100f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x100f8800 0x8000>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_0_MASTER_RESET>;
+			reset-names = "master";
 
 			status = "disabled";
+
+			dwc3_0: dwc3@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_0>, <&ss_phy_0>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
 		};
 
-		saw0: regulator@2089000 {
-			compatible = "qcom,saw2";
-			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+		hs_phy_0: phy@100f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
 		};
 
-		saw1: regulator@2099000 {
-			compatible = "qcom,saw2";
-			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+		ss_phy_0: phy@100f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb3_1: usb3@110f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x110f8800 0x8000>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_1_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_1: dwc3@11000000 {
+				compatible = "snps,dwc3";
+				reg = <0x11000000 0xcd00>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_1>, <&ss_phy_1>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_1: phy@110f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x110f8800 0x30>;
+			clocks = <&gcc USB30_1_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_1: phy@110f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x110f8830 0x30>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		amba: amba {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sdcc3: mmc@12180000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x12180000 0x2000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <192000000>;
+				sd-uhs-sdr104;
+				sd-uhs-ddr50;
+				vqmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+				dma-names = "tx", "rx";
+			};
+
+			sdcc1: mmc@12400000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg = <0x12400000 0x2000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <96000000>;
+				non-removable;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				mmc-ddr-1_8v;
+				vmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+				dma-names = "tx", "rx";
+			};
 		};
 
 		gsbi1: gsbi@12440000 {
@@ -654,56 +875,6 @@ i2c@16380000 {
 			};
 		};
 
-		gsbi5: gsbi@1a200000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <5>;
-			reg = <0x1a200000 0x100>;
-			clocks = <&gcc GSBI5_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			status = "disabled";
-
-			syscon-tcsr = <&tcsr>;
-
-			gsbi5_serial: serial@1a240000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x1a240000 0x1000>,
-				      <0x1a200000 0x1000>;
-				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-
-			i2c@1a280000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				reg = <0x1a280000 0x1000>;
-				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-
-			spi@1a280000 {
-				compatible = "qcom,spi-qup-v1.1.1";
-				reg = <0x1a280000 0x1000>;
-				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-
-				#address-cells = <1>;
-				#size-cells = <0>;
-			};
-		};
-
 		gsbi6: gsbi@16500000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			reg = <0x16500000 0x100>;
@@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 {
 			};
 		};
 
-		rng@1a500000 {
-			compatible = "qcom,prng";
-			reg = <0x1a500000 0x200>;
-			clocks = <&gcc PRNG_CLK>;
-			clock-names = "core";
-		};
+		adm_dma: dma-controller@18300000 {
+			compatible = "qcom,adm";
+			reg = <0x18300000 0x100000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
 
-		sata_phy: sata-phy@1b400000 {
-			compatible = "qcom,ipq806x-sata-phy";
-			reg = <0x1b400000 0x200>;
+			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+			clock-names = "core", "iface";
 
-			clocks = <&gcc SATA_PHY_CFG_CLK>;
-			clock-names = "cfg";
+			resets = <&gcc ADM0_RESET>,
+				 <&gcc ADM0_PBUS_RESET>,
+				 <&gcc ADM0_C0_RESET>,
+				 <&gcc ADM0_C1_RESET>,
+				 <&gcc ADM0_C2_RESET>;
+			reset-names = "clk", "pbus", "c0", "c1", "c2";
+			qcom,ee = <0>;
 
-			#phy-cells = <0>;
 			status = "disabled";
 		};
 
-		nand: nand-controller@1ac00000 {
-			compatible = "qcom,ipq806x-nand";
-			reg = <0x1ac00000 0x800>;
-
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
-
-			clocks = <&gcc EBI2_CLK>,
-				 <&gcc EBI2_AON_CLK>;
-			clock-names = "core", "aon";
-
-			dmas = <&adm_dma 3>;
-			dma-names = "rxtx";
-			qcom,cmd-crci = <15>;
-			qcom,data-crci = <3>;
-
+		gsbi5: gsbi@1a200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x1a200000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
 			#address-cells = <1>;
-			#size-cells = <0>;
-
+			#size-cells = <1>;
+			ranges;
 			status = "disabled";
-		};
 
-		sata: sata@29000000 {
-			compatible = "qcom,ipq806x-ahci", "generic-ahci";
-			reg = <0x29000000 0x180>;
+			syscon-tcsr = <&tcsr>;
 
-			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+			gsbi5_serial: serial@1a240000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x1a240000 0x1000>,
+				      <0x1a200000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
 
-			clocks = <&gcc SFAB_SATA_S_H_CLK>,
-				 <&gcc SATA_H_CLK>,
-				 <&gcc SATA_A_CLK>,
-				 <&gcc SATA_RXOOB_CLK>,
-				 <&gcc SATA_PMALIVE_CLK>;
-			clock-names = "slave_face", "iface", "core",
-					"rxoob", "pmalive";
+			i2c@1a280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x1a280000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
 
-			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
-			assigned-clock-rates = <100000000>, <100000000>;
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
 
-			phys = <&sata_phy>;
-			phy-names = "sata-phy";
-			status = "disabled";
-		};
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 
-		qcom,ssbi@500000 {
-			compatible = "qcom,ssbi";
-			reg = <0x00500000 0x1000>;
-			qcom,controller-type = "pmic-arbiter";
-		};
+			spi@1a280000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x1a280000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
 
-		qfprom: qfprom@700000 {
-			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
-			reg = <0x00700000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			speedbin_efuse: speedbin@c0 {
-				reg = <0xc0 0x4>;
-			};
-			tsens_calib: calib@400 {
-				reg = <0x400 0xb>;
-			};
-			tsens_calib_backup: calib_backup@410 {
-				reg = <0x410 0xb>;
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
 			};
 		};
 
-		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-ipq8064", "syscon";
-			clocks = <&pxo_board>, <&cxo_board>;
-			clock-names = "pxo", "cxo";
-			reg = <0x00900000 0x4000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-
-			tsens: thermal-sensor@900000 {
-				compatible = "qcom,ipq8064-tsens";
-
-				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
-				nvmem-cell-names = "calib", "calib_backup";
-				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "uplow";
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-ipq8064", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
 
-				#qcom,sensors = <11>;
-				#thermal-sensor-cells = <1>;
-			};
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
 		};
 
-		rpm: rpm@108000 {
-			compatible = "qcom,rpm-ipq8064";
-			reg = <0x108000 0x1000>;
-			qcom,ipc = <&l2cc 0x8 2>;
+		nand: nand-controller@1ac00000 {
+			compatible = "qcom,ipq806x-nand";
+			reg = <0x1ac00000 0x800>;
 
-			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
-					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "ack", "err", "wakeup";
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
 
-			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
-			clock-names = "ram";
+			clocks = <&gcc EBI2_CLK>,
+				 <&gcc EBI2_AON_CLK>;
+			clock-names = "core", "aon";
+
+			dmas = <&adm_dma 3>;
+			dma-names = "rxtx";
+			qcom,cmd-crci = <15>;
+			qcom,data-crci = <3>;
 
-			rpmcc: clock-controller {
-				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
-				#clock-cells = <1>;
-			};
-		};
+			#address-cells = <1>;
+			#size-cells = <0>;
 
-		tcsr: syscon@1a400000 {
-			compatible = "qcom,tcsr-ipq8064", "syscon";
-			reg = <0x1a400000 0x100>;
+			status = "disabled";
 		};
 
-		l2cc: clock-controller@2011000 {
-			compatible = "qcom,kpss-gcc", "syscon";
-			reg = <0x2011000 0x1000>;
-			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
-			clock-names = "pll8_vote", "pxo";
-			clock-output-names = "acpu_l2_aux";
-		};
+		sata_phy: sata-phy@1b400000 {
+			compatible = "qcom,ipq806x-sata-phy";
+			reg = <0x1b400000 0x200>;
 
-		lcc: clock-controller@28000000 {
-			compatible = "qcom,lcc-ipq8064";
-			reg = <0x28000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
+
+			#phy-cells = <0>;
+			status = "disabled";
 		};
 
 		pcie0: pci@1b500000 {
@@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 {
 			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
 		};
 
-		nss_common: syscon@03000000 {
-			compatible = "syscon";
-			reg = <0x03000000 0x0000FFFF>;
-		};
-
 		qsgmii_csr: syscon@1bb00000 {
 			compatible = "syscon";
 			reg = <0x1bb00000 0x000001FF>;
 		};
 
-		stmmac_axi_setup: stmmac-axi-config {
-			snps,wr_osr_lmt = <7>;
-			snps,rd_osr_lmt = <7>;
-			snps,blen = <16 0 0 0 0 0 0>;
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-ipq8064";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		lpass@28100000 {
+			compatible = "qcom,lpass-cpu";
+			status = "disabled";
+			clocks = <&lcc AHBIX_CLK>,
+					<&lcc MI2S_OSR_CLK>,
+					<&lcc MI2S_BIT_CLK>;
+			clock-names = "ahbix-clk",
+					"mi2s-osr-clk",
+					"mi2s-bit-clk";
+			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "lpass-irq-lpaif";
+			reg = <0x28100000 0x10000>;
+			reg-names = "lpass-lpaif";
+		};
+
+		sata: sata@29000000 {
+			compatible = "qcom,ipq806x-ahci", "generic-ahci";
+			reg = <0x29000000 0x180>;
+
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_face", "iface", "core",
+					"rxoob", "pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy>;
+			phy-names = "sata-phy";
+			status = "disabled";
 		};
 
 		gmac0: ethernet@37000000 {
@@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 {
 
 			status = "disabled";
 		};
-
-		hs_phy_0: phy@100f8800 {
-			compatible = "qcom,ipq806x-usb-phy-hs";
-			reg = <0x100f8800 0x30>;
-			clocks = <&gcc USB30_0_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		ss_phy_0: phy@100f8830 {
-			compatible = "qcom,ipq806x-usb-phy-ss";
-			reg = <0x100f8830 0x30>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		usb3_0: usb3@100f8800 {
-			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x100f8800 0x8000>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "core";
-
-			ranges;
-
-			resets = <&gcc USB30_0_MASTER_RESET>;
-			reset-names = "master";
-
-			status = "disabled";
-
-			dwc3_0: dwc3@10000000 {
-				compatible = "snps,dwc3";
-				reg = <0x10000000 0xcd00>;
-				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&hs_phy_0>, <&ss_phy_0>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-				snps,dis_u3_susphy_quirk;
-			};
-		};
-
-		hs_phy_1: phy@110f8800 {
-			compatible = "qcom,ipq806x-usb-phy-hs";
-			reg = <0x110f8800 0x30>;
-			clocks = <&gcc USB30_1_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		ss_phy_1: phy@110f8830 {
-			compatible = "qcom,ipq806x-usb-phy-ss";
-			reg = <0x110f8830 0x30>;
-			clocks = <&gcc USB30_1_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		usb3_1: usb3@110f8800 {
-			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x110f8800 0x8000>;
-			clocks = <&gcc USB30_1_MASTER_CLK>;
-			clock-names = "core";
-
-			ranges;
-
-			resets = <&gcc USB30_1_MASTER_RESET>;
-			reset-names = "master";
-
-			status = "disabled";
-
-			dwc3_1: dwc3@11000000 {
-				compatible = "snps,dwc3";
-				reg = <0x11000000 0xcd00>;
-				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&hs_phy_1>, <&ss_phy_1>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-				snps,dis_u3_susphy_quirk;
-			};
-		};
-
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		sdcc1bam: dma-controller@12402000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12402000 0x8000>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc3bam: dma-controller@12182000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12182000 0x8000>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC3_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		amba: amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			sdcc1: mmc@12400000 {
-				status = "disabled";
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg = <0x12400000 0x2000>;
-				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <8>;
-				max-frequency = <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				mmc-ddr-1_8v;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc3: mmc@12180000 {
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status = "disabled";
-				reg = <0x12180000 0x2000>;
-				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <8>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency = <192000000>;
-				sd-uhs-sdr104;
-				sd-uhs-ddr50;
-				vqmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
-				dma-names = "tx", "rx";
-			};
-		};
-
-		sfpb_mutex: hwlock@1200600 {
-			compatible = "qcom,sfpb-mutex";
-			reg = <0x01200600 0x100>;
-
-			#hwlock-cells = <1>;
-		};
 	};
 };
-- 
2.36.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux