Re: [PATCH 1/2] ARM: dts: qcom: ipq8064: reorganize node order and sort them

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Jul 18, 2022 at 05:38:14PM +0200, Christian Marangi wrote:
> Reorganize node order and sort them by address.
>

So how to proceed with this? Should I send v2 with the changes pointed
(stuff with no reg outside soc) or it's a NACK for the unnecessary
changes?

I feel a bit stuck.

> Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> ---
> 
> This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
> 
> [1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
> 
>  arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++--------------
>  1 file changed, 383 insertions(+), 383 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
> index da90f7c08d75..cf41d330c920 100644
> --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
> +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
> @@ -332,19 +332,59 @@ soc: soc {
>  		ranges;
>  		compatible = "simple-bus";
>  
> -		lpass@28100000 {
> -			compatible = "qcom,lpass-cpu";
> -			status = "disabled";
> -			clocks = <&lcc AHBIX_CLK>,
> -					<&lcc MI2S_OSR_CLK>,
> -					<&lcc MI2S_BIT_CLK>;
> -			clock-names = "ahbix-clk",
> -					"mi2s-osr-clk",
> -					"mi2s-bit-clk";
> -			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
> -			interrupt-names = "lpass-irq-lpaif";
> -			reg = <0x28100000 0x10000>;
> -			reg-names = "lpass-lpaif";
> +		stmmac_axi_setup: stmmac-axi-config {
> +			snps,wr_osr_lmt = <7>;
> +			snps,rd_osr_lmt = <7>;
> +			snps,blen = <16 0 0 0 0 0 0>;
> +		};
> +
> +		vsdcc_fixed: vsdcc-regulator {
> +			compatible = "regulator-fixed";
> +			regulator-name = "SDCC Power";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-always-on;
> +		};
> +
> +		rpm: rpm@108000 {
> +			compatible = "qcom,rpm-ipq8064";
> +			reg = <0x108000 0x1000>;
> +			qcom,ipc = <&l2cc 0x8 2>;
> +
> +			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "ack", "err", "wakeup";
> +
> +			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
> +			clock-names = "ram";
> +
> +			rpmcc: clock-controller {
> +				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
> +				#clock-cells = <1>;
> +			};
> +		};
> +
> +		qcom,ssbi@500000 {
> +			compatible = "qcom,ssbi";
> +			reg = <0x00500000 0x1000>;
> +			qcom,controller-type = "pmic-arbiter";
> +		};
> +
> +		qfprom: qfprom@700000 {
> +			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
> +			reg = <0x00700000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			speedbin_efuse: speedbin@c0 {
> +				reg = <0xc0 0x4>;
> +			};
> +			tsens_calib: calib@400 {
> +				reg = <0x400 0xb>;
> +			};
> +			tsens_calib_backup: calib_backup@410 {
> +				reg = <0x410 0xb>;
> +			};
>  		};
>  
>  		qcom_pinmux: pinmux@800000 {
> @@ -471,6 +511,35 @@ mux {
>  			};
>  		};
>  
> +		gcc: clock-controller@900000 {
> +			compatible = "qcom,gcc-ipq8064", "syscon";
> +			clocks = <&pxo_board>, <&cxo_board>;
> +			clock-names = "pxo", "cxo";
> +			reg = <0x00900000 0x4000>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +			#power-domain-cells = <1>;
> +
> +			tsens: thermal-sensor@900000 {
> +				compatible = "qcom,ipq8064-tsens";
> +
> +				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
> +				nvmem-cell-names = "calib", "calib_backup";
> +				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
> +				interrupt-names = "uplow";
> +
> +				#qcom,sensors = <11>;
> +				#thermal-sensor-cells = <1>;
> +			};
> +		};
> +
> +		sfpb_mutex: hwlock@1200600 {
> +			compatible = "qcom,sfpb-mutex";
> +			reg = <0x01200600 0x100>;
> +
> +			#hwlock-cells = <1>;
> +		};
> +
>  		intc: interrupt-controller@2000000 {
>  			compatible = "qcom,msm-qgic2";
>  			interrupt-controller;
> @@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>,
>  			cpu-offset = <0x80000>;
>  		};
>  
> +		l2cc: clock-controller@2011000 {
> +			compatible = "qcom,kpss-gcc", "syscon";
> +			reg = <0x2011000 0x1000>;
> +			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
> +			clock-names = "pll8_vote", "pxo";
> +			clock-output-names = "acpu_l2_aux";
> +		};
> +
>  		acc0: clock-controller@2088000 {
>  			compatible = "qcom,kpss-acc-v1";
>  			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
>  		};
>  
> +		saw0: regulator@2089000 {
> +			compatible = "qcom,saw2";
> +			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
> +			regulator;
> +		};
> +
>  		acc1: clock-controller@2098000 {
>  			compatible = "qcom,kpss-acc-v1";
>  			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
>  		};
>  
> -		adm_dma: dma-controller@18300000 {
> -			compatible = "qcom,adm";
> -			reg = <0x18300000 0x100000>;
> -			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> -			#dma-cells = <1>;
> +		saw1: regulator@2099000 {
> +			compatible = "qcom,saw2";
> +			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
> +			regulator;
> +		};
>  
> -			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
> -			clock-names = "core", "iface";
> +		nss_common: syscon@03000000 {
> +			compatible = "syscon";
> +			reg = <0x03000000 0x0000FFFF>;
> +		};
>  
> -			resets = <&gcc ADM0_RESET>,
> -				 <&gcc ADM0_PBUS_RESET>,
> -				 <&gcc ADM0_C0_RESET>,
> -				 <&gcc ADM0_C1_RESET>,
> -				 <&gcc ADM0_C2_RESET>;
> -			reset-names = "clk", "pbus", "c0", "c1", "c2";
> -			qcom,ee = <0>;
> +		usb3_0: usb3@100f8800 {
> +			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			reg = <0x100f8800 0x8000>;
> +			clocks = <&gcc USB30_0_MASTER_CLK>;
> +			clock-names = "core";
> +
> +			ranges;
> +
> +			resets = <&gcc USB30_0_MASTER_RESET>;
> +			reset-names = "master";
>  
>  			status = "disabled";
> +
> +			dwc3_0: dwc3@10000000 {
> +				compatible = "snps,dwc3";
> +				reg = <0x10000000 0xcd00>;
> +				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
> +				phys = <&hs_phy_0>, <&ss_phy_0>;
> +				phy-names = "usb2-phy", "usb3-phy";
> +				dr_mode = "host";
> +				snps,dis_u3_susphy_quirk;
> +			};
>  		};
>  
> -		saw0: regulator@2089000 {
> -			compatible = "qcom,saw2";
> -			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
> -			regulator;
> +		hs_phy_0: phy@100f8800 {
> +			compatible = "qcom,ipq806x-usb-phy-hs";
> +			reg = <0x100f8800 0x30>;
> +			clocks = <&gcc USB30_0_UTMI_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
>  		};
>  
> -		saw1: regulator@2099000 {
> -			compatible = "qcom,saw2";
> -			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
> -			regulator;
> +		ss_phy_0: phy@100f8830 {
> +			compatible = "qcom,ipq806x-usb-phy-ss";
> +			reg = <0x100f8830 0x30>;
> +			clocks = <&gcc USB30_0_MASTER_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
> +		usb3_1: usb3@110f8800 {
> +			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			reg = <0x110f8800 0x8000>;
> +			clocks = <&gcc USB30_1_MASTER_CLK>;
> +			clock-names = "core";
> +
> +			ranges;
> +
> +			resets = <&gcc USB30_1_MASTER_RESET>;
> +			reset-names = "master";
> +
> +			status = "disabled";
> +
> +			dwc3_1: dwc3@11000000 {
> +				compatible = "snps,dwc3";
> +				reg = <0x11000000 0xcd00>;
> +				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
> +				phys = <&hs_phy_1>, <&ss_phy_1>;
> +				phy-names = "usb2-phy", "usb3-phy";
> +				dr_mode = "host";
> +				snps,dis_u3_susphy_quirk;
> +			};
> +		};
> +
> +		hs_phy_1: phy@110f8800 {
> +			compatible = "qcom,ipq806x-usb-phy-hs";
> +			reg = <0x110f8800 0x30>;
> +			clocks = <&gcc USB30_1_UTMI_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
> +		ss_phy_1: phy@110f8830 {
> +			compatible = "qcom,ipq806x-usb-phy-ss";
> +			reg = <0x110f8830 0x30>;
> +			clocks = <&gcc USB30_1_MASTER_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
> +		sdcc3bam: dma-controller@12182000 {
> +			compatible = "qcom,bam-v1.3.0";
> +			reg = <0x12182000 0x8000>;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc SDC3_H_CLK>;
> +			clock-names = "bam_clk";
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +		};
> +
> +		sdcc1bam: dma-controller@12402000 {
> +			compatible = "qcom,bam-v1.3.0";
> +			reg = <0x12402000 0x8000>;
> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc SDC1_H_CLK>;
> +			clock-names = "bam_clk";
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +		};
> +
> +		amba: amba {
> +			compatible = "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			sdcc3: mmc@12180000 {
> +				compatible = "arm,pl18x", "arm,primecell";
> +				arm,primecell-periphid = <0x00051180>;
> +				status = "disabled";
> +				reg = <0x12180000 0x2000>;
> +				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> +				interrupt-names = "cmd_irq";
> +				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
> +				clock-names = "mclk", "apb_pclk";
> +				bus-width = <8>;
> +				cap-sd-highspeed;
> +				cap-mmc-highspeed;
> +				max-frequency = <192000000>;
> +				sd-uhs-sdr104;
> +				sd-uhs-ddr50;
> +				vqmmc-supply = <&vsdcc_fixed>;
> +				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
> +				dma-names = "tx", "rx";
> +			};
> +
> +			sdcc1: mmc@12400000 {
> +				status = "disabled";
> +				compatible = "arm,pl18x", "arm,primecell";
> +				arm,primecell-periphid = <0x00051180>;
> +				reg = <0x12400000 0x2000>;
> +				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> +				interrupt-names = "cmd_irq";
> +				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
> +				clock-names = "mclk", "apb_pclk";
> +				bus-width = <8>;
> +				max-frequency = <96000000>;
> +				non-removable;
> +				cap-sd-highspeed;
> +				cap-mmc-highspeed;
> +				mmc-ddr-1_8v;
> +				vmmc-supply = <&vsdcc_fixed>;
> +				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
> +				dma-names = "tx", "rx";
> +			};
>  		};
>  
>  		gsbi1: gsbi@12440000 {
> @@ -654,56 +875,6 @@ i2c@16380000 {
>  			};
>  		};
>  
> -		gsbi5: gsbi@1a200000 {
> -			compatible = "qcom,gsbi-v1.0.0";
> -			cell-index = <5>;
> -			reg = <0x1a200000 0x100>;
> -			clocks = <&gcc GSBI5_H_CLK>;
> -			clock-names = "iface";
> -			#address-cells = <1>;
> -			#size-cells = <1>;
> -			ranges;
> -			status = "disabled";
> -
> -			syscon-tcsr = <&tcsr>;
> -
> -			gsbi5_serial: serial@1a240000 {
> -				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
> -				reg = <0x1a240000 0x1000>,
> -				      <0x1a200000 0x1000>;
> -				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
> -				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
> -				clock-names = "core", "iface";
> -				status = "disabled";
> -			};
> -
> -			i2c@1a280000 {
> -				compatible = "qcom,i2c-qup-v1.1.1";
> -				reg = <0x1a280000 0x1000>;
> -				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> -
> -				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> -				clock-names = "core", "iface";
> -				status = "disabled";
> -
> -				#address-cells = <1>;
> -				#size-cells = <0>;
> -			};
> -
> -			spi@1a280000 {
> -				compatible = "qcom,spi-qup-v1.1.1";
> -				reg = <0x1a280000 0x1000>;
> -				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> -
> -				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> -				clock-names = "core", "iface";
> -				status = "disabled";
> -
> -				#address-cells = <1>;
> -				#size-cells = <0>;
> -			};
> -		};
> -
>  		gsbi6: gsbi@16500000 {
>  			compatible = "qcom,gsbi-v1.0.0";
>  			reg = <0x16500000 0x100>;
> @@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 {
>  			};
>  		};
>  
> -		rng@1a500000 {
> -			compatible = "qcom,prng";
> -			reg = <0x1a500000 0x200>;
> -			clocks = <&gcc PRNG_CLK>;
> -			clock-names = "core";
> -		};
> +		adm_dma: dma-controller@18300000 {
> +			compatible = "qcom,adm";
> +			reg = <0x18300000 0x100000>;
> +			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> +			#dma-cells = <1>;
>  
> -		sata_phy: sata-phy@1b400000 {
> -			compatible = "qcom,ipq806x-sata-phy";
> -			reg = <0x1b400000 0x200>;
> +			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
> +			clock-names = "core", "iface";
>  
> -			clocks = <&gcc SATA_PHY_CFG_CLK>;
> -			clock-names = "cfg";
> +			resets = <&gcc ADM0_RESET>,
> +				 <&gcc ADM0_PBUS_RESET>,
> +				 <&gcc ADM0_C0_RESET>,
> +				 <&gcc ADM0_C1_RESET>,
> +				 <&gcc ADM0_C2_RESET>;
> +			reset-names = "clk", "pbus", "c0", "c1", "c2";
> +			qcom,ee = <0>;
>  
> -			#phy-cells = <0>;
>  			status = "disabled";
>  		};
>  
> -		nand: nand-controller@1ac00000 {
> -			compatible = "qcom,ipq806x-nand";
> -			reg = <0x1ac00000 0x800>;
> -
> -			pinctrl-0 = <&nand_pins>;
> -			pinctrl-names = "default";
> -
> -			clocks = <&gcc EBI2_CLK>,
> -				 <&gcc EBI2_AON_CLK>;
> -			clock-names = "core", "aon";
> -
> -			dmas = <&adm_dma 3>;
> -			dma-names = "rxtx";
> -			qcom,cmd-crci = <15>;
> -			qcom,data-crci = <3>;
> -
> +		gsbi5: gsbi@1a200000 {
> +			compatible = "qcom,gsbi-v1.0.0";
> +			cell-index = <5>;
> +			reg = <0x1a200000 0x100>;
> +			clocks = <&gcc GSBI5_H_CLK>;
> +			clock-names = "iface";
>  			#address-cells = <1>;
> -			#size-cells = <0>;
> -
> +			#size-cells = <1>;
> +			ranges;
>  			status = "disabled";
> -		};
>  
> -		sata: sata@29000000 {
> -			compatible = "qcom,ipq806x-ahci", "generic-ahci";
> -			reg = <0x29000000 0x180>;
> +			syscon-tcsr = <&tcsr>;
>  
> -			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
> +			gsbi5_serial: serial@1a240000 {
> +				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
> +				reg = <0x1a240000 0x1000>,
> +				      <0x1a200000 0x1000>;
> +				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
> +				clock-names = "core", "iface";
> +				status = "disabled";
> +			};
>  
> -			clocks = <&gcc SFAB_SATA_S_H_CLK>,
> -				 <&gcc SATA_H_CLK>,
> -				 <&gcc SATA_A_CLK>,
> -				 <&gcc SATA_RXOOB_CLK>,
> -				 <&gcc SATA_PMALIVE_CLK>;
> -			clock-names = "slave_face", "iface", "core",
> -					"rxoob", "pmalive";
> +			i2c@1a280000 {
> +				compatible = "qcom,i2c-qup-v1.1.1";
> +				reg = <0x1a280000 0x1000>;
> +				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
>  
> -			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
> -			assigned-clock-rates = <100000000>, <100000000>;
> +				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> +				clock-names = "core", "iface";
> +				status = "disabled";
>  
> -			phys = <&sata_phy>;
> -			phy-names = "sata-phy";
> -			status = "disabled";
> -		};
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
>  
> -		qcom,ssbi@500000 {
> -			compatible = "qcom,ssbi";
> -			reg = <0x00500000 0x1000>;
> -			qcom,controller-type = "pmic-arbiter";
> -		};
> +			spi@1a280000 {
> +				compatible = "qcom,spi-qup-v1.1.1";
> +				reg = <0x1a280000 0x1000>;
> +				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
>  
> -		qfprom: qfprom@700000 {
> -			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
> -			reg = <0x00700000 0x1000>;
> -			#address-cells = <1>;
> -			#size-cells = <1>;
> -			speedbin_efuse: speedbin@c0 {
> -				reg = <0xc0 0x4>;
> -			};
> -			tsens_calib: calib@400 {
> -				reg = <0x400 0xb>;
> -			};
> -			tsens_calib_backup: calib_backup@410 {
> -				reg = <0x410 0xb>;
> +				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
> +				clock-names = "core", "iface";
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
>  			};
>  		};
>  
> -		gcc: clock-controller@900000 {
> -			compatible = "qcom,gcc-ipq8064", "syscon";
> -			clocks = <&pxo_board>, <&cxo_board>;
> -			clock-names = "pxo", "cxo";
> -			reg = <0x00900000 0x4000>;
> -			#clock-cells = <1>;
> -			#reset-cells = <1>;
> -			#power-domain-cells = <1>;
> -
> -			tsens: thermal-sensor@900000 {
> -				compatible = "qcom,ipq8064-tsens";
> -
> -				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
> -				nvmem-cell-names = "calib", "calib_backup";
> -				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
> -				interrupt-names = "uplow";
> +		tcsr: syscon@1a400000 {
> +			compatible = "qcom,tcsr-ipq8064", "syscon";
> +			reg = <0x1a400000 0x100>;
> +		};
>  
> -				#qcom,sensors = <11>;
> -				#thermal-sensor-cells = <1>;
> -			};
> +		rng@1a500000 {
> +			compatible = "qcom,prng";
> +			reg = <0x1a500000 0x200>;
> +			clocks = <&gcc PRNG_CLK>;
> +			clock-names = "core";
>  		};
>  
> -		rpm: rpm@108000 {
> -			compatible = "qcom,rpm-ipq8064";
> -			reg = <0x108000 0x1000>;
> -			qcom,ipc = <&l2cc 0x8 2>;
> +		nand: nand-controller@1ac00000 {
> +			compatible = "qcom,ipq806x-nand";
> +			reg = <0x1ac00000 0x800>;
>  
> -			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> -					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> -					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> -			interrupt-names = "ack", "err", "wakeup";
> +			pinctrl-0 = <&nand_pins>;
> +			pinctrl-names = "default";
>  
> -			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
> -			clock-names = "ram";
> +			clocks = <&gcc EBI2_CLK>,
> +				 <&gcc EBI2_AON_CLK>;
> +			clock-names = "core", "aon";
> +
> +			dmas = <&adm_dma 3>;
> +			dma-names = "rxtx";
> +			qcom,cmd-crci = <15>;
> +			qcom,data-crci = <3>;
>  
> -			rpmcc: clock-controller {
> -				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
> -				#clock-cells = <1>;
> -			};
> -		};
> +			#address-cells = <1>;
> +			#size-cells = <0>;
>  
> -		tcsr: syscon@1a400000 {
> -			compatible = "qcom,tcsr-ipq8064", "syscon";
> -			reg = <0x1a400000 0x100>;
> +			status = "disabled";
>  		};
>  
> -		l2cc: clock-controller@2011000 {
> -			compatible = "qcom,kpss-gcc", "syscon";
> -			reg = <0x2011000 0x1000>;
> -			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
> -			clock-names = "pll8_vote", "pxo";
> -			clock-output-names = "acpu_l2_aux";
> -		};
> +		sata_phy: sata-phy@1b400000 {
> +			compatible = "qcom,ipq806x-sata-phy";
> +			reg = <0x1b400000 0x200>;
>  
> -		lcc: clock-controller@28000000 {
> -			compatible = "qcom,lcc-ipq8064";
> -			reg = <0x28000000 0x1000>;
> -			#clock-cells = <1>;
> -			#reset-cells = <1>;
> +			clocks = <&gcc SATA_PHY_CFG_CLK>;
> +			clock-names = "cfg";
> +
> +			#phy-cells = <0>;
> +			status = "disabled";
>  		};
>  
>  		pcie0: pci@1b500000 {
> @@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 {
>  			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
>  		};
>  
> -		nss_common: syscon@03000000 {
> -			compatible = "syscon";
> -			reg = <0x03000000 0x0000FFFF>;
> -		};
> -
>  		qsgmii_csr: syscon@1bb00000 {
>  			compatible = "syscon";
>  			reg = <0x1bb00000 0x000001FF>;
>  		};
>  
> -		stmmac_axi_setup: stmmac-axi-config {
> -			snps,wr_osr_lmt = <7>;
> -			snps,rd_osr_lmt = <7>;
> -			snps,blen = <16 0 0 0 0 0 0>;
> +		lcc: clock-controller@28000000 {
> +			compatible = "qcom,lcc-ipq8064";
> +			reg = <0x28000000 0x1000>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		lpass@28100000 {
> +			compatible = "qcom,lpass-cpu";
> +			status = "disabled";
> +			clocks = <&lcc AHBIX_CLK>,
> +					<&lcc MI2S_OSR_CLK>,
> +					<&lcc MI2S_BIT_CLK>;
> +			clock-names = "ahbix-clk",
> +					"mi2s-osr-clk",
> +					"mi2s-bit-clk";
> +			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "lpass-irq-lpaif";
> +			reg = <0x28100000 0x10000>;
> +			reg-names = "lpass-lpaif";
> +		};
> +
> +		sata: sata@29000000 {
> +			compatible = "qcom,ipq806x-ahci", "generic-ahci";
> +			reg = <0x29000000 0x180>;
> +
> +			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&gcc SFAB_SATA_S_H_CLK>,
> +				 <&gcc SATA_H_CLK>,
> +				 <&gcc SATA_A_CLK>,
> +				 <&gcc SATA_RXOOB_CLK>,
> +				 <&gcc SATA_PMALIVE_CLK>;
> +			clock-names = "slave_face", "iface", "core",
> +					"rxoob", "pmalive";
> +
> +			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
> +			assigned-clock-rates = <100000000>, <100000000>;
> +
> +			phys = <&sata_phy>;
> +			phy-names = "sata-phy";
> +			status = "disabled";
>  		};
>  
>  		gmac0: ethernet@37000000 {
> @@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 {
>  
>  			status = "disabled";
>  		};
> -
> -		hs_phy_0: phy@100f8800 {
> -			compatible = "qcom,ipq806x-usb-phy-hs";
> -			reg = <0x100f8800 0x30>;
> -			clocks = <&gcc USB30_0_UTMI_CLK>;
> -			clock-names = "ref";
> -			#phy-cells = <0>;
> -
> -			status = "disabled";
> -		};
> -
> -		ss_phy_0: phy@100f8830 {
> -			compatible = "qcom,ipq806x-usb-phy-ss";
> -			reg = <0x100f8830 0x30>;
> -			clocks = <&gcc USB30_0_MASTER_CLK>;
> -			clock-names = "ref";
> -			#phy-cells = <0>;
> -
> -			status = "disabled";
> -		};
> -
> -		usb3_0: usb3@100f8800 {
> -			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> -			#address-cells = <1>;
> -			#size-cells = <1>;
> -			reg = <0x100f8800 0x8000>;
> -			clocks = <&gcc USB30_0_MASTER_CLK>;
> -			clock-names = "core";
> -
> -			ranges;
> -
> -			resets = <&gcc USB30_0_MASTER_RESET>;
> -			reset-names = "master";
> -
> -			status = "disabled";
> -
> -			dwc3_0: dwc3@10000000 {
> -				compatible = "snps,dwc3";
> -				reg = <0x10000000 0xcd00>;
> -				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
> -				phys = <&hs_phy_0>, <&ss_phy_0>;
> -				phy-names = "usb2-phy", "usb3-phy";
> -				dr_mode = "host";
> -				snps,dis_u3_susphy_quirk;
> -			};
> -		};
> -
> -		hs_phy_1: phy@110f8800 {
> -			compatible = "qcom,ipq806x-usb-phy-hs";
> -			reg = <0x110f8800 0x30>;
> -			clocks = <&gcc USB30_1_UTMI_CLK>;
> -			clock-names = "ref";
> -			#phy-cells = <0>;
> -
> -			status = "disabled";
> -		};
> -
> -		ss_phy_1: phy@110f8830 {
> -			compatible = "qcom,ipq806x-usb-phy-ss";
> -			reg = <0x110f8830 0x30>;
> -			clocks = <&gcc USB30_1_MASTER_CLK>;
> -			clock-names = "ref";
> -			#phy-cells = <0>;
> -
> -			status = "disabled";
> -		};
> -
> -		usb3_1: usb3@110f8800 {
> -			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
> -			#address-cells = <1>;
> -			#size-cells = <1>;
> -			reg = <0x110f8800 0x8000>;
> -			clocks = <&gcc USB30_1_MASTER_CLK>;
> -			clock-names = "core";
> -
> -			ranges;
> -
> -			resets = <&gcc USB30_1_MASTER_RESET>;
> -			reset-names = "master";
> -
> -			status = "disabled";
> -
> -			dwc3_1: dwc3@11000000 {
> -				compatible = "snps,dwc3";
> -				reg = <0x11000000 0xcd00>;
> -				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
> -				phys = <&hs_phy_1>, <&ss_phy_1>;
> -				phy-names = "usb2-phy", "usb3-phy";
> -				dr_mode = "host";
> -				snps,dis_u3_susphy_quirk;
> -			};
> -		};
> -
> -		vsdcc_fixed: vsdcc-regulator {
> -			compatible = "regulator-fixed";
> -			regulator-name = "SDCC Power";
> -			regulator-min-microvolt = <3300000>;
> -			regulator-max-microvolt = <3300000>;
> -			regulator-always-on;
> -		};
> -
> -		sdcc1bam: dma-controller@12402000 {
> -			compatible = "qcom,bam-v1.3.0";
> -			reg = <0x12402000 0x8000>;
> -			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> -			clocks = <&gcc SDC1_H_CLK>;
> -			clock-names = "bam_clk";
> -			#dma-cells = <1>;
> -			qcom,ee = <0>;
> -		};
> -
> -		sdcc3bam: dma-controller@12182000 {
> -			compatible = "qcom,bam-v1.3.0";
> -			reg = <0x12182000 0x8000>;
> -			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> -			clocks = <&gcc SDC3_H_CLK>;
> -			clock-names = "bam_clk";
> -			#dma-cells = <1>;
> -			qcom,ee = <0>;
> -		};
> -
> -		amba: amba {
> -			compatible = "simple-bus";
> -			#address-cells = <1>;
> -			#size-cells = <1>;
> -			ranges;
> -
> -			sdcc1: mmc@12400000 {
> -				status = "disabled";
> -				compatible = "arm,pl18x", "arm,primecell";
> -				arm,primecell-periphid = <0x00051180>;
> -				reg = <0x12400000 0x2000>;
> -				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> -				interrupt-names = "cmd_irq";
> -				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
> -				clock-names = "mclk", "apb_pclk";
> -				bus-width = <8>;
> -				max-frequency = <96000000>;
> -				non-removable;
> -				cap-sd-highspeed;
> -				cap-mmc-highspeed;
> -				mmc-ddr-1_8v;
> -				vmmc-supply = <&vsdcc_fixed>;
> -				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
> -				dma-names = "tx", "rx";
> -			};
> -
> -			sdcc3: mmc@12180000 {
> -				compatible = "arm,pl18x", "arm,primecell";
> -				arm,primecell-periphid = <0x00051180>;
> -				status = "disabled";
> -				reg = <0x12180000 0x2000>;
> -				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> -				interrupt-names = "cmd_irq";
> -				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
> -				clock-names = "mclk", "apb_pclk";
> -				bus-width = <8>;
> -				cap-sd-highspeed;
> -				cap-mmc-highspeed;
> -				max-frequency = <192000000>;
> -				sd-uhs-sdr104;
> -				sd-uhs-ddr50;
> -				vqmmc-supply = <&vsdcc_fixed>;
> -				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
> -				dma-names = "tx", "rx";
> -			};
> -		};
> -
> -		sfpb_mutex: hwlock@1200600 {
> -			compatible = "qcom,sfpb-mutex";
> -			reg = <0x01200600 0x100>;
> -
> -			#hwlock-cells = <1>;
> -		};
>  	};
>  };
> -- 
> 2.36.1
> 

-- 
	Ansuel



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux