Siddharth,
On 03/06/2022 13:49, Siddharth Vadapalli wrote:
> Hello Roger,
>
> On 03/06/22 14:18, Roger Quadros wrote:
>> Hi Siddharth,
>>
>> On 01/06/2022 14:27, Siddharth Vadapalli wrote:
>>> Hello Roger,
>>>
>>> On 01/06/22 15:08, Roger Quadros wrote:
>>>> Siddharth,
>>>>
>>>> On 01/06/2022 09:01, Siddharth Vadapalli wrote:
>>>>> Hello Roger,
>>>>>
>>>>> On 31/05/22 17:15, Roger Quadros wrote:
>>>>>> Hi Siddharth,
>>>>>>
>>>>>> On 31/05/2022 14:12, Siddharth Vadapalli wrote:
>>>>>>> TI's J7200 SoC supports additional PHY modes like QSGMII and SGMII
>>>>>>> that are not supported on earlier SoCs. Add a compatible for it.
>>>>>>>
>>>>>>> Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx>
>>>>>>> ---
>>>>>>> .../mfd/ti,j721e-system-controller.yaml | 5 ++++
>>>>>>> .../bindings/phy/ti,phy-gmii-sel.yaml | 24 ++++++++++++++++++-
>>>>>>> 2 files changed, 28 insertions(+), 1 deletion(-)
>>>>>>>
>>>>>>> diff --git a/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml b/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
>>>>>>> index fa86691ebf16..e381ba62a513 100644
>>>>>>> --- a/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
>>>>>>> +++ b/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
>>>>>>> @@ -48,6 +48,11 @@ patternProperties:
>>>>>>> description:
>>>>>>> This is the SERDES lane control mux.
>>>>>>>
>>>>>>> + "phy@[0-9a-f]+$":
>>>>>>> + type: object
>>>>>>> + description:
>>>>>>> + This is the register to set phy mode through phy-gmii-sel driver.
>>>>>>> +
>>>>>>
>>>>>> Is this really required? The system controller has 100s of different such registers and it is not practical to mention about all.
>>>>>
>>>>> The property has to be mentioned in order to pass: make dtbs_check.
>>>>>
>>>>>>
>>>>>>> required:
>>>>>>> - compatible
>>>>>>> - reg
>>>>>>> diff --git a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
>>>>>>> index ff8a6d9eb153..7427758451e7 100644
>>>>>>> --- a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
>>>>>>> +++ b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
>>>>>>> @@ -53,12 +53,21 @@ properties:
>>>>>>> - ti,am43xx-phy-gmii-sel
>>>>>>> - ti,dm814-phy-gmii-sel
>>>>>>> - ti,am654-phy-gmii-sel
>>>>>>> + - ti,j7200-cpsw5g-phy-gmii-sel
>>>>>>
>>>>>> Why not just "ti,j7200-phy-gmii-sel" so it is consistent naming.
>>>>>
>>>>> In TI's J7200 device, there are two CPSW MACs, namely CPSW2G and CPSW5G. While
>>>>> CPSW5G supports QSGMII mode, CPSW2G does not. Hence, the compatible being added
>>>>> with the extra mode (QSGMII) enabled is applicable only for CPSW5G and not for
>>>>> CPSW2G. Thus, to highlight this, the word "CPSW5G" has been included in the name
>>>>> of the compatible.
>>>>
>>>> Here we are talking about the PHY driver (phy-gmii-sel) and not the MAC (CPSW2G / CPSW5G)
>>>> Does this PHY on J7200 always support QSGMII mode? if yes then embedding "cpsw5g" in compatible is wrong.
>>>
>>> The PHY on J7200 is part of the Add-On Ethernet card. It is possible to connect
>>> RGMII, QSGMII and SGMII PHY. The CPSW5G MAC supports all these modes. With the
>>> current patch, I am adding just QSGMII mode as an extra mode, but in a future
>>> patch, I will be adding SGMII also as an extra mode. For this reason, CPSW5G is
>>> being mentioned in the compatible name, to differentiate supported modes for
>>> CPSW2G and CPSW5G. Also, the phy-gmii-sel driver actually configures CPSW MAC
>>> registers and not the PHY.
>>
>> phy-gmii-sel configures CTRL MMR register right? How does it configure CPSW MAC register?
>>
>> Anyways, I just looked at the TRM and there are in fact separate phy-gmii-sel (ENET_CTRL)
>> registers for CPSW2g and CPSW5g. So they warrant for separate compatibles as they are
>> not identical.
>
> By CPSW MAC registers being configured, I meant that the configuration being
> done is for the MAC and not for the PHY. As per the TRM, for CPSW2G, the
> CTRLMMR_MCU_ENET_CTRL register is configured and for CPSW5G, the
> CTRLMMR_ENETx_CTRL registers are configured, with x ranging from 1 to 4
> (corresponding to the 4 ports of CPSW5G). These registers configure the CPSW MAC
> (CPSW2G/CPSW5G) and not the PHY. For this reason, I think that it would be
> appropriate to use cpsw5g in the compatible name, to indicate which CTRLMMR
> registers are being configured.
Yes, I already agreed that separate compatible is fine :).
>
>>>
>>>>
>>>> You need to use a different compatible in CPSW driver and make sure CPSW2G doesn't initiate QSGMII mode.
>>>
>>> Yes, I will add a check there too by using a different compatible in the CPSW
>>> driver, but shouldn't the phy-gmii-sel driver also have a check to ensure that
>>> it doesn't try configuring QSGMII mode for CPSW2G?
>>
>> Yes, additional check in phy-gmii-sel driver is fine.
>>
>>>
>>>>
>>>>>
>>>>>>
>>>>>>>
>>>>>>> reg:
>>>>>>> maxItems: 1
>>>>>>>
>>>>>>> '#phy-cells': true
>>>>>>>
>>>>>>> + ti,enet-ctrl-qsgmii:
>>>>>>> + $ref: /schemas/types.yaml#/definitions/uint32
>>>>>>> + description: |
>>>>>>> + Required only for QSGMII mode. Bitmask to select the port for
>>>>>>> + QSGMII main mode. Rest of the ports are selected as QSGMII_SUB
>>>>>>> + ports automatically. Any of the 4 CPSW5G ports can act as the
>>>>>>> + main port with the rest of them being the QSGMII_SUB ports.
>>>>>>> +
>>>>>>
>>>>>> This is weird way of doing things.
>>>>>>
>>>>>> The Ethernet controller driver already knows which mode the port is
>>>>>> supposed to operate.
>>>>>
>>>>> From the ethernet driver perspective, there is no difference between the QSGMII
>>>>> or QSGMII-SUB modes and both are treated the same. However, the phy-gmii-sel
>>>>> driver configures CPSW MAC registers differently depending on the mode being
>>
>> You mean the ENET_CTRL register in CTRL_MMR space?
>
> Yes I am referring to the CTRLMMR_ENETx_CTRL registers as per the J7200 TRM,
> corresponding to the CPSW5G MAC.
>
>>
>>>>> QSGMII or QSGMII-SUB. Hence, the ti,enet-ctrl-qsgmii property is used to
>>>>> identify the QSGMII main port and the rest are configured in CPSW MAC as
>>>>> QSGMII-SUB ports.
>>>>>
>>>>>>
>>>>>> e.g.
>>>>>> +&cpsw0_port1 {
>>>>>> + phy-handle = <&cpsw5g_phy0>;
>>>>>> + phy-mode = "qsgmii";
>>>>>> + mac-address = [00 00 00 00 00 00];
>>>>>> + phys = <&cpsw0_phy_gmii_sel 1>;
>>>>>> +};
>>>>>> +
>>>>>> +&cpsw0_port2 {
>>>>>> + phy-handle = <&cpsw5g_phy1>;
>>>>>> + phy-mode = "qsgmii-sub";
>>>>>> + mac-address = [00 00 00 00 00 00];
>>>>>> + phys = <&cpsw0_phy_gmii_sel 2>;
>>>>>>
>>>>>> And it can convey the mode to the PHY driver via phy_ops->set_mode.
>>>>>> So you should be depending on that instead of adding this new property.
>>>>>
>>>>> QSGMII-SUB is not a standard mode in the Linux kernel. In order to proceed with
>>>>> the suggested implementation, a new phy mode named PHY_INTERFACE_MODE_QSGMII_SUB
>>>>> has to be introduced to the kernel. Additionally, all existing phy drivers will
>>>>> have to be updated to recognize the new phy mode.
>>>>>
>>>>> Since the QSGMII-SUB mode is TI specific, it was decided that it would be better
>>>>> to add a new property in TI specific files for identifying the QSGMII main port
>>>>> and treating the rest as QSGMII-SUB ports.
>>>>
>>>> Who decides which port should be MAIN and which should be SUB? Can all ports be MAIN?
>>>> Can all ports be SUB or there has to be at least one MAIN?
>>>
>>> All 4 ports in CPSW5G have the capability to be the MAIN port, with the only
>>> restriction being that only one of them should be the MAIN port at a time. The
>>> role of the CPSW5G ports is decided based on what PHY port each of the CPSW5G
>>> ports connects to.
>>
>> OK, then instead of using bitmask and property being named "ti,enet-ctrl-qsgmii", why not
>> just say "ti,qsgmii-main-port" = <main_port_number>;
>
> I plan to send patches for J721e device which has CPSW9G (8 external ports) MAC.
> CPSW9G can work with two sets of QSGMII interfaces (4 ports + 4 ports). Thus,
> using a bitmask for the QSGMII main port will help identify the QSGMII main port
> across both sets of QSGMII interfaces. The bitmask in case of J721e CPSW9G will
> consider the first 4 bits for the first interface's 4 ports and the next 4 bits
> for the second interface's 4 ports. In this manner, it will be possible to
> extend it for 8 port CPSW9G MAC as well, without having to add a new property
> for the second QSGMII interface.
>
>>
>> Also do some sanity check when getting that property.
>
> To ensure that multiple QSGMII ports are not declared as the main port, the
> "ti,enet-ctrl-qsgmii" property has been declared as an enum: [1,2,4,8]. If a
All I'm saying is that instead of bitmask please use port number to specify main port.
You can use minimum/maximum to limit the values.
Take care of limit checking per compatible and converting into bitmask in the driver.
> different value other than the value in enum were to be used, then "make
> dtbs_check" would raise an error. This will prevent configuring multiple QSGMII
> ports as the main port at once. Also, in the phy-gmii-sel driver, a default
> value of 1 is being assigned to the variable that will store the value
> corresponding to the ti,enet-ctrl-qsgmii property from the device tree, thereby
> treating the first CPSW5G port as the QSGMII main port by default.
>
> Thanks,
> Siddharth.
cheers,
-roger
