Hi Geert,
On Fri, Apr 29, 2022 at 10:53 AM Geert Uytterhoeven
<geert@xxxxxxxxxxxxxx> wrote:
>
> Hi Prabhakar,
>
> On Fri, Apr 29, 2022 at 11:43 AM Lad, Prabhakar
> <prabhakar.csengg@xxxxxxxxx> wrote:
> > On Thu, Apr 28, 2022 at 10:42 AM Geert Uytterhoeven
> > <geert@xxxxxxxxxxxxxx> wrote:
> > > On Fri, Apr 22, 2022 at 12:12 AM Lad Prabhakar
> > > <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
> > > > Add a driver for the Renesas RZ/G2L Interrupt Controller.
> > > >
> > > > This supports external pins being used as interrupts. It supports
> > > > one line for NMI, 8 external pins and 32 GPIO pins (out of 123)
> > > > to be used as IRQ lines.
> > > >
> > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
>
> > > > --- /dev/null
> > > > +++ b/drivers/irqchip/irq-renesas-rzg2l.c
> > > > @@ -0,0 +1,447 @@
> > > > +// SPDX-License-Identifier: GPL-2.0
> > > > +/*
> > > > + * Renesas RZ/G2L IRQC Driver
> > > > + *
> > > > + * Copyright (C) 2022 Renesas Electronics Corporation.
> > > > + *
> > > > + * Author: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > > > + */
> > > > +
> > > > +#include <linux/clk.h>
> > > > +#include <linux/err.h>
> > > > +#include <linux/io.h>
> > > > +#include <linux/irqchip.h>
> > > > +#include <linux/irqdomain.h>
> > > > +#include <linux/of_address.h>
> > > > +#include <linux/reset.h>
> > > > +#include <linux/spinlock.h>
> > > > +
> > > > +#define IRQC_IRQ_START 1
> > > > +#define IRQC_IRQ_COUNT 8
> > > > +#define IRQC_TINT_START 9
> > >
> > > = IRQC_IRQ_START + IRQC_IRQ_COUNT
> > >
> > OK
> >
> > > > +#define IRQC_TINT_COUNT 32
> > > > +#define IRQC_NUM_IRQ 41
> > >
> > > = IRQC_TINT_START + IRQC_TINT_COUNT
> > >
> > OK.
> >
> > > Should these be in a DT binding header file?
> > >
> > > Combining all types into a single linear number space makes it hard
> > > to extend the range, when reusing for an SoC that supports more
> > > interrupt sources.
> > >
> > Or DT data maybe?
>
> Let's leave it for now. As I missed that DT consumers will refer to
> external interrupt numbers only (is that actually enforced?), there
> won't be an issue.
>
> The driver can be changed later to derive IRQC_IRQ_COUNT from the
> compatible value, when needed.
>
Agreed.
> > > > + u32 reg;
> > > > +
> > > > + reg = readl_relaxed(priv->base + ISCR);
> > > > + if (reg & bit)
> > > > + writel_relaxed(GENMASK(IRQC_IRQ_COUNT - 1, 0) & ~bit,
> > >
> > > As writes to the unused upper bits are ignored, you can drop the
> > > masking with GENMASK(IRQC_IRQ_COUNT - 1, 0), and be prepared for more
> > > interrupt sources.
> > >
> > Agreed.
>
> > > > + u32 bit = BIT(hw_irq - IRQC_TINT_START);
> > > > + u32 reg;
> > > > +
> > > > + reg = readl_relaxed(priv->base + TSCR);
> > > > + if (reg & bit)
> > > > + writel_relaxed(GENMASK(IRQC_TINT_COUNT - 1, 0) & ~bit,
> > >
> > > Drop the masking with all-ones?
> > >
> > You mean instead of a mask just use the reg instead?
>
> No, I meant to drop the masking with GENMASK(IRQC_TINT_COUNT - 1, 0),
> cfr. for external interrupts.
>
Ahh right, I missed that.
Cheers,
Prabhakar
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
