On Tue, Apr 05, 2022 at 10:14:20AM -0700, Matthias Kaehlcke wrote:
> On Tue, Apr 05, 2022 at 04:42:47PM +0530, Srinivasa Rao Mandadapu wrote:
> > Add LPASS LPI pinctrl node required for Audio functionality on sc7280
> > based platforms.
> >
> > Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
> > Co-developed-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
> > Signed-off-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 98 ++++++++++++++++++++++++++++
> > arch/arm64/boot/dts/qcom/sc7280.dtsi | 107 +++++++++++++++++++++++++++++++
> > 2 files changed, 205 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > index 2afbbe3..f912a89 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > @@ -238,6 +238,104 @@
> > modem-init;
> > };
> >
> > +&lpass_tlmm {
> > + dmic01_active: dmic01-active {
> > + clk {
> > + drive-strength = <8>;
> > + };
> > +
> > + data {
> > + drive-strength = <8>;
>
> The DMIC data pins are input pins, right? Why does an input pin need a drive
> strength? Same for other input pins.
>
> > + };
> > + };
>
> There's no need to reference 'lpass_tlmm' nor to repeat $label: $node.
> Instead just use phandles:
>
> &dmic01_active {
> clk {
> drive-strength = <8>;
> };
>
> data {
> drive-strength = <8>;
> };
> };
>
> Rather than replicating the node hierarchy you could also just give each pin a
> label, and then:
>
> &dmic01_clk_active {
> drive-strength = <8>;
> };
>
> &dmic01_data_active {
> drive-strength = <8>;
> };
>
> I don't have a strong preference, but wonder if the grouping adds any value.
One more thing: please also drop the '_active' suffix, it is not needed. With
that I think it's clearer to get rid of the grouping.
> > +
> > + dmic01_sleep: dmic01-sleep {
> > + clk {
> > + drive-strength = <2>;
> > + bias-disable;
> > + };
> > +
> > + data {
> > + drive-strength = <2>;
> > + pull-down;
> > + };
> > + };
> > +
> > + dmic23_active: dmic02-active {
> > + clk {
> > + drive-strength = <8>;
> > + };
> > +
> > + data {
> > + drive-strength = <8>;
> > + };
> > + };
> > +
> > + dmic23_sleep: dmic02-sleep {
> > + clk {
> > + drive-strength = <2>;
> > + bias-disable;
> > + };
> > +
> > + data {
> > + drive-strength = <2>;
> > + pull-down;
> > + };
> > + };
> > +
> > + rx_swr_active: rx-swr-active {
> > + clk {
> > + drive-strength = <2>;
> > + slew-rate = <1>;
> > + bias-disable;
> > + };
> > +
> > + data {
> > + drive-strength = <2>;
> > + slew-rate = <1>;
> > + bias-bus-hold;
> > + };
> > + };
> > +
> > + rx_swr_sleep: rx-swr-sleep {
> > + clk {
> > + drive-strength = <2>;
> > + bias-pull-down;
> > + };
> > +
> > + data {
> > + drive-strength = <2>;
> > + bias-pull-down;
> > + };
> > + };
> > +
> > + tx_swr_active: tx-swr-active {
> > + clk {
> > + drive-strength = <2>;
> > + slew-rate = <1>;
> > + bias-disable;
> > + };
> > +
> > + data {
> > + drive-strength = <2>;
> > + slew-rate = <1>;
> > + bias-bus-hold;
> > + };
> > + };
> > +
> > + tx_swr_sleep: tx-swr-sleep {
> > + clk {
> > + drive-strength = <2>;
> > + bias-pull-down;
> > + };
> > +
> > + data {
> > + drive-strength = <2>;
> > + bias-bus-hold;
> > + };
> > + };
> > +};
> > +
> > &pcie1 {
> > status = "okay";
> > perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
> > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > index 8d8cec5..db74fc3 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> > @@ -1987,6 +1987,113 @@
> > qcom,bcm-voters = <&apps_bcm_voter>;
> > };
> >
> > + lpass_tlmm: pinctrl@33c0000 {
> > + compatible = "qcom,sc7280-lpass-lpi-pinctrl";
> > + reg = <0 0x33c0000 0x0 0x20000>,
> > + <0 0x3550000 0x0 0x10000>;
>
> Pad addresses to 8 digits.
>
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-ranges = <&lpass_tlmm 0 0 15>;
> > +
> > + #clock-cells = <1>;
> > +
> > + dmic01_active: dmic01-active {
> > + clk {
> > + pins = "gpio6";
> > + function = "dmic1_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio7";
> > + function = "dmic1_data";
> > + };
> > + };
> > +
> > + dmic01_sleep: dmic01-sleep {
> > + clk {
> > + pins = "gpio6";
> > + function = "dmic1_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio7";
> > + function = "dmic1_data";
> > + };
> > + };
> > +
> > + dmic23_active: dmic02-active {
>
> is it intentional that the node name is 'dmic02*', but the label 'dmic23*'?
>
> > + clk {
> > + pins = "gpio8";
> > + function = "dmic2_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio9";
> > + function = "dmic2_data";
> > + };
> > + };
> > +
> > + dmic23_sleep: dmic02-sleep {
>
> ditto
>
> > + clk {
> > + pins = "gpio8";
> > + function = "dmic2_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio9";
> > + function = "dmic2_data";
> > + };
> > + };
> > +
> > + rx_swr_active: rx-swr-active {
> > + clk {
> > + pins = "gpio3";
> > + function = "swr_rx_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio4", "gpio5";
> > + function = "swr_rx_data";
> > + };
> > + };
> > +
> > + rx_swr_sleep: rx-swr-sleep {
> > + clk {
> > + pins = "gpio3";
> > + function = "swr_rx_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio4", "gpio5";
> > + function = "swr_rx_data";
> > + };
> > + };
> > +
> > + tx_swr_active: tx-swr-active {
> > + clk {
> > + pins = "gpio0";
> > + function = "swr_tx_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio1", "gpio2", "gpio14";
> > + function = "swr_tx_data";
> > + };
> > + };
> > +
> > + tx_swr_sleep: tx-swr-sleep {
> > + clk {
> > + pins = "gpio0";
> > + function = "swr_tx_clk";
> > + };
> > +
> > + data {
> > + pins = "gpio1", "gpio2", "gpio14";
> > + function = "swr_tx_data";
> > + };
> > + };
> > + };
> > +
> > gpu: gpu@3d00000 {
> > compatible = "qcom,adreno-635.0", "qcom,adreno";
> > reg = <0 0x03d00000 0 0x40000>,
