On 4/6/2022 7:45 AM, Matthias Kaehlcke wrote:
Thanks Matthias for your time and Valuable inputs!!!
On Tue, Apr 05, 2022 at 10:14:20AM -0700, Matthias Kaehlcke wrote:
On Tue, Apr 05, 2022 at 04:42:47PM +0530, Srinivasa Rao Mandadapu wrote:
Add LPASS LPI pinctrl node required for Audio functionality on sc7280
based platforms.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 98 ++++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sc7280.dtsi | 107 +++++++++++++++++++++++++++++++
2 files changed, 205 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 2afbbe3..f912a89 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -238,6 +238,104 @@
modem-init;
};
+&lpass_tlmm {
+ dmic01_active: dmic01-active {
+ clk {
+ drive-strength = <8>;
+ };
+
+ data {
+ drive-strength = <8>;
The DMIC data pins are input pins, right? Why does an input pin need a drive
strength? Same for other input pins.
Okay. Will remove this.
+ };
+ };
There's no need to reference 'lpass_tlmm' nor to repeat $label: $node.
Instead just use phandles:
Okay. Will change accordingly.
&dmic01_active {
clk {
drive-strength = <8>;
};
data {
drive-strength = <8>;
};
};
Rather than replicating the node hierarchy you could also just give each pin a
label, and then:
&dmic01_clk_active {
drive-strength = <8>;
};
&dmic01_data_active {
drive-strength = <8>;
};
I don't have a strong preference, but wonder if the grouping adds any value.
One more thing: please also drop the '_active' suffix, it is not needed. With
that I think it's clearer to get rid of the grouping.
For now will continue as it's. Anyway we are removing dmic01_data_active.
+
+ dmic01_sleep: dmic01-sleep {
+ clk {
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ data {
+ drive-strength = <2>;
+ pull-down;
+ };
+ };
+
+ dmic23_active: dmic02-active {
+ clk {
+ drive-strength = <8>;
+ };
+
+ data {
+ drive-strength = <8>;
+ };
+ };
+
+ dmic23_sleep: dmic02-sleep {
+ clk {
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ data {
+ drive-strength = <2>;
+ pull-down;
+ };
+ };
+
+ rx_swr_active: rx-swr-active {
+ clk {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ rx_swr_sleep: rx-swr-sleep {
+ clk {
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ data {
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ tx_swr_active: tx-swr-active {
+ clk {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ tx_swr_sleep: tx-swr-sleep {
+ clk {
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ data {
+ drive-strength = <2>;
+ bias-bus-hold;
+ };
+ };
+};
+
&pcie1 {
status = "okay";
perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 8d8cec5..db74fc3 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -1987,6 +1987,113 @@
qcom,bcm-voters = <&apps_bcm_voter>;
};
+ lpass_tlmm: pinctrl@33c0000 {
+ compatible = "qcom,sc7280-lpass-lpi-pinctrl";
+ reg = <0 0x33c0000 0x0 0x20000>,
+ <0 0x3550000 0x0 0x10000>;
Pad addresses to 8 digits.
Okay.
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&lpass_tlmm 0 0 15>;
+
+ #clock-cells = <1>;
+
+ dmic01_active: dmic01-active {
+ clk {
+ pins = "gpio6";
+ function = "dmic1_clk";
+ };
+
+ data {
+ pins = "gpio7";
+ function = "dmic1_data";
+ };
+ };
+
+ dmic01_sleep: dmic01-sleep {
+ clk {
+ pins = "gpio6";
+ function = "dmic1_clk";
+ };
+
+ data {
+ pins = "gpio7";
+ function = "dmic1_data";
+ };
+ };
+
+ dmic23_active: dmic02-active {
is it intentional that the node name is 'dmic02*', but the label 'dmic23*'?
typo error. will fix it.
+ clk {
+ pins = "gpio8";
+ function = "dmic2_clk";
+ };
+
+ data {
+ pins = "gpio9";
+ function = "dmic2_data";
+ };
+ };
+
+ dmic23_sleep: dmic02-sleep {
ditto
Okay.
+ clk {
+ pins = "gpio8";
+ function = "dmic2_clk";
+ };
+
+ data {
+ pins = "gpio9";
+ function = "dmic2_data";
+ };
+ };
+
+ rx_swr_active: rx-swr-active {
+ clk {
+ pins = "gpio3";
+ function = "swr_rx_clk";
+ };
+
+ data {
+ pins = "gpio4", "gpio5";
+ function = "swr_rx_data";
+ };
+ };
+
+ rx_swr_sleep: rx-swr-sleep {
+ clk {
+ pins = "gpio3";
+ function = "swr_rx_clk";
+ };
+
+ data {
+ pins = "gpio4", "gpio5";
+ function = "swr_rx_data";
+ };
+ };
+
+ tx_swr_active: tx-swr-active {
+ clk {
+ pins = "gpio0";
+ function = "swr_tx_clk";
+ };
+
+ data {
+ pins = "gpio1", "gpio2", "gpio14";
+ function = "swr_tx_data";
+ };
+ };
+
+ tx_swr_sleep: tx-swr-sleep {
+ clk {
+ pins = "gpio0";
+ function = "swr_tx_clk";
+ };
+
+ data {
+ pins = "gpio1", "gpio2", "gpio14";
+ function = "swr_tx_data";
+ };
+ };
+ };
+
gpu: gpu@3d00000 {
compatible = "qcom,adreno-635.0", "qcom,adreno";
reg = <0 0x03d00000 0 0x40000>,
