Hi Hans, On Tue, Jul 29, 2014 at 07:02:28PM +0200, Hans de Goede wrote: > The Banana Pi is an A20 based development board using Raspberry Pi compatible > IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi > and stereo audio out + various expenansion headers: > > http://www.bananapi.org/ > > Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/sun7i-a20-bananapi.dts | 183 +++++++++++++++++++++++++++++++ > 2 files changed, 184 insertions(+) > create mode 100644 arch/arm/boot/dts/sun7i-a20-bananapi.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index bdbc84a..440e037 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -379,6 +379,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \ > sun6i-a31-hummingbird.dtb \ > sun6i-a31-m9.dtb > dtb-$(CONFIG_MACH_SUN7I) += \ > + sun7i-a20-bananapi.dtb \ > sun7i-a20-cubieboard2.dtb \ > sun7i-a20-cubietruck.dtb \ > sun7i-a20-i12-tvbox.dtb \ > diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts > new file mode 100644 > index 0000000..0332b82 > --- /dev/null > +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts > @@ -0,0 +1,183 @@ > +/* > + * Copyright 2014 Hans de Goede <hdegoede@xxxxxxxxxx> > + * > + * The code contained herein is licensed under the GNU General Public > + * License. You may obtain a copy of the GNU General Public License > + * Version 2 or later at the following locations: > + * > + * http://www.opensource.org/licenses/gpl-license.html > + * http://www.gnu.org/copyleft/gpl.html > + */ > + > +/dts-v1/; > +/include/ "sun7i-a20.dtsi" > +/include/ "sunxi-common-regulators.dtsi" > + > +/ { > + model = "LeMaker Banana Pi"; > + compatible = "lemaker,bananapi", "allwinner,sun7i-a20"; > + > + soc@01c00000 { > + spi0: spi@01c05000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0_pins_a>; > + status = "okay"; > + }; > + > + mmc0: mmc@01c0f000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <4>; > + cd-gpios = <&pio 7 10 0>; /* PH10 */ > + cd-inverted; > + status = "okay"; > + }; > + > + usbphy: phy@01c13400 { > + usb1_vbus-supply = <®_usb1_vbus>; > + usb2_vbus-supply = <®_usb2_vbus>; > + status = "okay"; > + }; > + > + ehci0: usb@01c14000 { > + status = "okay"; > + }; > + > + ohci0: usb@01c14400 { > + status = "okay"; > + }; > + > + ahci: sata@01c18000 { > + status = "okay"; > + }; > + > + ehci1: usb@01c1c000 { > + status = "okay"; > + }; > + > + ohci1: usb@01c1c400 { > + status = "okay"; > + }; > + > + pinctrl@01c20800 { > + uart3_pins_bananapi: uart3_pin@0 { > + allwinner,pins = "PH0", "PH1"; > + allwinner,function = "uart3"; > + allwinner,drive = <0>; > + allwinner,pull = <0>; > + }; That node should be in the DTSI > + > + mmc0_cd_pin_bananapi: mmc0_cd_pin@0 { > + allwinner,pins = "PH10"; > + allwinner,function = "gpio_in"; > + allwinner,drive = <0>; > + allwinner,pull = <1>; > + }; > + > + gmac_power_pin_bananapi: gmac_power_pin@0 { > + allwinner,pins = "PH23"; > + allwinner,function = "gpio_out"; > + allwinner,drive = <0>; > + allwinner,pull = <0>; > + }; > + > + led_pins_bananapi: led_pins@0 { > + allwinner,pins = "PH24"; > + allwinner,function = "gpio_out"; > + allwinner,drive = <0>; > + allwinner,pull = <0>; > + }; > + }; > + > + ir0: ir@01c21800 { > + pinctrl-names = "default"; > + pinctrl-0 = <&ir0_pins_a>; > + status = "okay"; > + }; > + > + uart0: serial@01c28000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pins_a>; > + status = "okay"; > + }; > + > + uart3: serial@01c28c00 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart3_pins_bananapi>; > + status = "okay"; > + }; > + > + uart7: serial@01c29c00 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart7_pins_a>; > + status = "okay"; > + }; > + > + i2c0: i2c@01c2ac00 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins_a>; > + status = "okay"; > + > + axp209: pmic@34 { > + compatible = "x-powers,axp209"; > + reg = <0x34>; > + interrupt-parent = <&nmi_intc>; > + interrupts = <0 8>; > + > + interrupt-controller; > + #interrupt-cells = <1>; > + }; > + }; > + > + i2c2: i2c@01c2b400 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins_a>; > + status = "okay"; > + }; > + > + gmac: ethernet@01c50000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&gmac_pins_rgmii_a>; > + phy = <&phy1>; > + phy-mode = "rgmii"; > + phy-supply = <®_gmac_3v3>; > + status = "okay"; > + > + phy1: ethernet-phy@1 { > + reg = <1>; > + }; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&led_pins_bananapi>; > + > + green { > + label = "bananapi:green:usr"; > + gpios = <&pio 7 24 0>; > + }; > + }; > + > + reg_usb1_vbus: usb1-vbus { > + status = "okay"; > + }; > + > + reg_usb2_vbus: usb2-vbus { > + status = "okay"; > + }; > + > + reg_gmac_3v3: gmac-3v3 { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&gmac_power_pin_bananapi>; > + regulator-name = "gmac-3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <50000>; > + enable-active-high; > + gpio = <&pio 7 23 0>; > + }; > +}; Looks fine otherwise, thanks! Maxime -- Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com
Attachment:
signature.asc
Description: Digital signature
