The Banana Pi is an A20 based development board using Raspberry Pi compatible IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi and stereo audio out + various expenansion headers: http://www.bananapi.org/ Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun7i-a20-bananapi.dts | 183 +++++++++++++++++++++++++++++++ 2 files changed, 184 insertions(+) create mode 100644 arch/arm/boot/dts/sun7i-a20-bananapi.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bdbc84a..440e037 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -379,6 +379,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-hummingbird.dtb \ sun6i-a31-m9.dtb dtb-$(CONFIG_MACH_SUN7I) += \ + sun7i-a20-bananapi.dtb \ sun7i-a20-cubieboard2.dtb \ sun7i-a20-cubietruck.dtb \ sun7i-a20-i12-tvbox.dtb \ diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts new file mode 100644 index 0000000..0332b82 --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -0,0 +1,183 @@ +/* + * Copyright 2014 Hans de Goede <hdegoede@xxxxxxxxxx> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "LeMaker Banana Pi"; + compatible = "lemaker,bananapi", "allwinner,sun7i-a20"; + + soc@01c00000 { + spi0: spi@01c05000 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>; + status = "okay"; + }; + + mmc0: mmc@01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 10 0>; /* PH10 */ + cd-inverted; + status = "okay"; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + + pinctrl@01c20800 { + uart3_pins_bananapi: uart3_pin@0 { + allwinner,pins = "PH0", "PH1"; + allwinner,function = "uart3"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + mmc0_cd_pin_bananapi: mmc0_cd_pin@0 { + allwinner,pins = "PH10"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <1>; + }; + + gmac_power_pin_bananapi: gmac_power_pin@0 { + allwinner,pins = "PH23"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + led_pins_bananapi: led_pins@0 { + allwinner,pins = "PH24"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + ir0: ir@01c21800 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_pins_a>; + status = "okay"; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + + uart3: serial@01c28c00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins_bananapi>; + status = "okay"; + }; + + uart7: serial@01c29c00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart7_pins_a>; + status = "okay"; + }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 8>; + + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + i2c2: i2c@01c2b400 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + }; + + gmac: ethernet@01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + phy-supply = <®_gmac_3v3>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_bananapi>; + + green { + label = "bananapi:green:usr"; + gpios = <&pio 7 24 0>; + }; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&gmac_power_pin_bananapi>; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <50000>; + enable-active-high; + gpio = <&pio 7 23 0>; + }; +}; -- 2.0.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
