Add Xilinx ZynqMP firmware MMIO APIs support to set and get PS_MODE
pins value and status. These APIs create an interface path between
mode pin controller driver and low-level API to access GPIO pins.
Signed-off-by: Piyush Mehta <piyush.mehta@xxxxxxxxxx>
---
Changes in v2:
- Added Xilinx ZynqMP firmware MMIO API support to set and get pin
value and status.
---
drivers/firmware/xilinx/zynqmp.c | 46 ++++++++++++++++++++++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 14 +++++++++++
2 files changed, 60 insertions(+)
diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
index 15b13832..0234423 100644
--- a/drivers/firmware/xilinx/zynqmp.c
+++ b/drivers/firmware/xilinx/zynqmp.c
@@ -28,6 +28,13 @@
/* Max HashMap Order for PM API feature check (1<<7 = 128) */
#define PM_API_FEATURE_CHECK_MAX_ORDER 7
+/* CRL registers and bitfields */
+#define CRL_APB_BASE 0xFF5E0000U
+/* BOOT_PIN_CTRL- Used to control the mode pins after boot */
+#define CRL_APB_BOOT_PIN_CTRL (CRL_APB_BASE + (0x250U))
+/* BOOT_PIN_CTRL_MASK- out_val[11:8], out_en[3:0] */
+#define CRL_APB_BOOTPIN_CTRL_MASK 0xF0FU
+
static bool feature_check_enabled;
static DEFINE_HASHTABLE(pm_api_features_map, PM_API_FEATURE_CHECK_MAX_ORDER);
@@ -926,6 +933,45 @@ int zynqmp_pm_pinctrl_set_config(const u32 pin, const u32 param,
EXPORT_SYMBOL_GPL(zynqmp_pm_pinctrl_set_config);
/**
+ * zynqmp_pm_bootmode_read() - PM Config API for read bootpin status
+ * @ps_mode: Returned output value of ps_mode
+ *
+ * This API function is to be used for notify the power management controller
+ * to read bootpin status.
+ *
+ * Return: status, either success or error+reason
+ */
+unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode)
+{
+ unsigned int ret;
+ u32 ret_payload[PAYLOAD_ARG_CNT];
+
+ ret = zynqmp_pm_invoke_fn(PM_MMIO_READ, CRL_APB_BOOT_PIN_CTRL, 0,
+ 0, 0, ret_payload);
+
+ *ps_mode = ret_payload[1];
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bootmode_read);
+
+/**
+ * zynqmp_pm_bootmode_write() - PM Config API for Configure bootpin
+ * @ps_mode: Value to be written to the bootpin ctrl register
+ *
+ * This API function is to be used for notify the power management controller
+ * to configure bootpin.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+int zynqmp_pm_bootmode_write(u32 ps_mode)
+{
+ return zynqmp_pm_invoke_fn(PM_MMIO_WRITE, CRL_APB_BOOT_PIN_CTRL,
+ CRL_APB_BOOTPIN_CTRL_MASK, ps_mode, 0, NULL);
+}
+EXPORT_SYMBOL_GPL(zynqmp_pm_bootmode_write);
+
+/**
* zynqmp_pm_init_finalize() - PM call to inform firmware that the caller
* master has initialized its own power management
*
diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
index 9d1a5c1..dc6f39f 100644
--- a/include/linux/firmware/xlnx-zynqmp.h
+++ b/include/linux/firmware/xlnx-zynqmp.h
@@ -68,6 +68,8 @@ enum pm_api_id {
PM_SET_REQUIREMENT = 15,
PM_RESET_ASSERT = 17,
PM_RESET_GET_STATUS = 18,
+ PM_MMIO_WRITE = 19,
+ PM_MMIO_READ = 20,
PM_PM_INIT_FINALIZE = 21,
PM_FPGA_LOAD = 22,
PM_FPGA_GET_STATUS = 23,
@@ -386,6 +388,8 @@ int zynqmp_pm_sd_dll_reset(u32 node_id, u32 type);
int zynqmp_pm_reset_assert(const enum zynqmp_pm_reset reset,
const enum zynqmp_pm_reset_action assert_flag);
int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset, u32 *status);
+unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode);
+int zynqmp_pm_bootmode_write(u32 ps_mode);
int zynqmp_pm_init_finalize(void);
int zynqmp_pm_set_suspend_mode(u32 mode);
int zynqmp_pm_request_node(const u32 node, const u32 capabilities,
@@ -515,6 +519,16 @@ static inline int zynqmp_pm_reset_get_status(const enum zynqmp_pm_reset reset,
return -ENODEV;
}
+static inline unsigned int zynqmp_pm_bootmode_read(u32 *ps_mode)
+{
+ return -ENODEV;
+}
+
+static inline int zynqmp_pm_bootmode_write(u32 ps_mode)
+{
+ return -ENODEV;
+}
+
static inline int zynqmp_pm_init_finalize(void)
{
return -ENODEV;
--
2.7.4
