On 30/07/2021 16:49, Sam Protsenko wrote:
> Samsung Exynos850 is ARMv8-based mobile-oriented SoC.
>
> Features:
> * CPU: Cortex-A55 Octa (8 cores), up to 2 GHz
> * Memory interface: LPDDR4/4x 2 channels (12.8 GB/s)
> * SD/MMC: SD 3.0, eMMC5.1 DDR 8-bit
> * Modem: 4G LTE, 3G, GSM/GPRS/EDGE
> * RF: Quad GNSS, WiFi 5 (802.11ac), Bluetooth 5.0
> * GPU: Mali-G52 MP1
> * Codec: 1080p 60fps H64, HEVC, JPEG HW Codec
> * Display: Full HD+ (2520x1080)@60fps LCD
> * Camera: 16+5MP/13+8MP ISP, MIPI CSI 4/4/2, FD, DRC
> * Connectivity: USB 2.0 DRD, USI (SPI/UART/I2C), HSI2C, I3C, ADC, Audio
Please document first the features you add (and are working) and
afterwards mention all others capabilities.
>
> This patch adds minimal SoC support. Particular board device tree files
> can include exynos850.dtsi file to get SoC related nodes, and then
> reference those nodes further as needed.
>
> Signed-off-by: Sam Protsenko <semen.protsenko@xxxxxxxxxx>
> ---
> .../boot/dts/exynos/exynos850-pinctrl.dtsi | 782 ++++++++++++++++++
> arch/arm64/boot/dts/exynos/exynos850-usi.dtsi | 30 +
> arch/arm64/boot/dts/exynos/exynos850.dtsi | 245 ++++++
Not buildable. Missing Makefile, missing DTS. Please submit with initial
DTS, otherwise no one is able to verify it even compiles.
> 3 files changed, 1057 insertions(+)
> create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> create mode 100644 arch/arm64/boot/dts/exynos/exynos850-usi.dtsi
> create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi
>
> diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> new file mode 100644
> index 000000000000..4cf0a22cc6db
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> @@ -0,0 +1,782 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
> + *
> + * Copyright (C) 2017 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
> + * tree nodes in this file.
> + */
> +
> +#include <dt-bindings/interrupt-controller/exynos850.h>
> +
> +/ {
> + /* ALIVE */
> + pinctrl@11850000 {
> + gpa0: gpa0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
That's odd a little, why three cells? How this would be used/referenced?
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__ALIVE_EINT0 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT1 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT2 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT5 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT6 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT7 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa1: gpa1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__ALIVE_EINT8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT9 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT10 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT13 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT15 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa2: gpa2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__ALIVE_EINT16 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT17 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT18 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT19 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT20 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT21 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT22 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT23 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa3: gpa3 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__ALIVE_EINT24 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT25 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT26 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT27 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT28 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT29 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT30 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT31 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa4: gpa4 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__ALIVE_EINT32 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT33 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT34 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT35 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpq0: gpq0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + /* USI_PERI_UART_DBG */
> + uart0_bus: uart0-bus {
> + samsung,pins = "gpq0-0", "gpq0-1";
> + samsung,pin-function = <2>;
EXYNOS_PIN_FUNC_2
> + samsung,pin-pud = <0>;
EXYNOS_PIN_PULL_xx?
> + };
> +
> + decon_f_te_on: decon_f_te_on {
1. Where is it used?
2. Use hyphens in node names.
Please build it with W=1 and fix the warnings.
> + samsung,pins = "gpa4-1";
Order the nodes based on first pin name, so:
i2c5_bus
i2c6_bus
decon_f_te_on
uart0_bus
> + samsung,pin-function = <0xf>;
> + };
> +
> + decon_f_te_off: decon_f_te_off {
Where is it used?
> + samsung,pins = "gpa4-1";
> + samsung,pin-function = <0x0>;
> + };
> +
> + /* I2C_5 | CAM_PMIC_I2C */
This comment is confusing. I2C-5 is obvious from node name and label.
CAM_PMIC_I2C does not look like property of SoC but board.
> + i2c5_bus: i2c5-bus {
> + samsung,pins = "gpa3-5", "gpa3-6";
> + samsung,pin-function = <3>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* I2C_6 | MOTOR_I2C */
> + i2c6_bus: i2c6-bus {
> + samsung,pins = "gpa3-7", "gpa4-0";
> + samsung,pin-function = <3>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> + };
> +
> + /* CMGP */
> + pinctrl@11c30000 {
> + gpm0: gpm0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__CMGP_EXT_INTM00 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm1: gpm1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__CMGP_EXT_INTM01 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm2: gpm2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__CMGP_EXT_INTM02 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm3: gpm3 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__CMGP_EXT_INTM03 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm4: gpm4 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__CMGP_EXT_INTM04 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm5: gpm5 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupt-parent = <&gic>;
> + interrupts =
> + <GIC_SPI INTREQ__CMGP_EXT_INTM05 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* usi_cmgp00 */
> + hsi2c3_bus: hsi2c3-bus {
> + samsung,pins = "gpm0-0", "gpm1-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* usi_cmgp01 */
> + hsi2c4_bus: hsi2c4-bus {
> + samsung,pins = "gpm4-0", "gpm5-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* spi usi_cmgp00 */
> + spi1_bus: spi1-bus {
> + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi1_cs: spi1-cs {
> + samsung,pins = "gpm3-0";
> + samsung,pin-function = <1>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi1_cs_func: spi1-cs-func {
> + samsung,pins = "gpm3-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* spi usi_cmgp01 */
> + spi2_bus: spi2-bus {
> + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi2_cs: spi2-cs {
> + samsung,pins = "gpm7-0";
> + samsung,pin-function = <1>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi2_cs_func: spi2-cs-func {
> + samsung,pins = "gpm7-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* usi_cmgp00_uart */
> + uart1_bus_single: uart1-bus {
> + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + };
> +
> + uart1_bus_dual: uart1-bus-dual {
> + samsung,pins = "gpm0-0", "gpm1-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + };
> +
> + /* usi_cmgp01_uart */
> + uart2_bus_single: uart2-bus {
> + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + };
> +
> + uart2_bus_dual: uart2-bus-dual {
> + samsung,pins = "gpm4-0", "gpm5-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + };
> + };
> +
> + /* AUD */
> + pinctrl@14a60000 {
> + gpb0: gpb0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpb1: gpb1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + aud_codec_mclk: aud-codec-mclk {
> + samsung,pins = "gpb0-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <1>;
> + };
> +
> + aud_codec_mclk_idle: aud-codec-mclk-idle {
> + samsung,pins = "gpb0-0";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <1>;
> + };
> +
> + aud_i2s0_bus: aud-i2s0-bus {
> + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <1>;
> + };
> +
> + aud_i2s0_idle: aud-i2s0-idle {
> + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <1>;
> + };
> +
> + aud_i2s1_bus: aud-i2s1-bus {
> + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <1>;
> + };
> +
> + aud_i2s1_idle: aud-i2s1-idle {
> + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <1>;
> + };
> +
> + aud_fm_bus: aud-fm-bus {
> + samsung,pins = "gpb1-4";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <1>;
> + };
> +
> + aud_fm_idle: aud-fm-idle {
> + samsung,pins = "gpb1-4";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <1>;
> + };
> + };
> +
> + /* HSI */
> + pinctrl@13430000 {
> + gpf2: gpf2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + sd2_clk: sd2-clk {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_cmd: sd2-cmd {
> + samsung,pins = "gpf2-1";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_bus1: sd2-bus-width1 {
> + samsung,pins = "gpf2-2";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_bus4: sd2-bus-width4 {
> + samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_clk_fast_slew_rate_1x: sd2-clk_fast_slew_rate_1x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + sd2_clk_fast_slew_rate_1_5x: sd2-clk_fast_slew_rate_1_5x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <1>;
> + };
> +
> + sd2_clk_fast_slew_rate_2x: sd2-clk_fast_slew_rate_2x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_clk_fast_slew_rate_2_5x: sd2-clk_fast_slew_rate_2_5x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd2_clk_fast_slew_rate_3x: sd2-clk_fast_slew_rate_3x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <4>;
> + };
> +
> + sd2_clk_fast_slew_rate_4x: sd2-clk_fast_slew_rate_4x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <5>;
> + };
> +
> + sd2_pins_as_pdn: sd2-pins-as-pdn {
> + samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
> + "gpf2-4", "gpf2-5";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <2>;
> + };
> +
No need for blank line.
> + };
> +
> + /* CORE */
> + pinctrl@12070000 {
> + gpf0: gpf0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + sd0_clk: sd0-clk {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_cmd: sd0-cmd {
> + samsung,pins = "gpf0-1";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_rdqs: sd0-rdqs {
> + samsung,pins = "gpf0-2";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <1>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_nreset: sd0-nreset {
> + samsung,pins = "gpf0-3";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_clk_fast_slew_rate_1x: sd0-clk_fast_slew_rate_1x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <1>;
> + };
> +
> + sd0_clk_fast_slew_rate_2x: sd0-clk_fast_slew_rate_2x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd0_clk_fast_slew_rate_3x: sd0-clk_fast_slew_rate_3x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd0_clk_fast_slew_rate_4x: sd0-clk_fast_slew_rate_4x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <3>;
> + };
> +
> + gpf1: gpf1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + sd0_bus1: sd0-bus-width1 {
> + samsung,pins = "gpf1-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_bus4: sd0-bus-width4 {
> + samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_bus8: sd0-bus-width8 {
> + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <3>;
> + };
> + };
> +
> + /* PERI */
> + pinctrl@139b0000 {
> + gpg0: gpg0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpp0: gpp0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + gpp1: gpp1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpp2: gpp2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpg1: gpg1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpg2: gpg2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpg3: gpg3 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpc0: gpc0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpc1: gpc1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + xclkout: xclkout {
> + samsung,pins = "gpq0-2";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + };
> +
> + /* usi_hsi2c_0 */
Comment seems to duplicate node name/label.
> + hsi2c0_bus: hsi2c0-bus {
> + samsung,pins = "gpc1-0", "gpc1-1";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* usi_hsi2c_1 */
> + hsi2c1_bus: hsi2c1-bus {
> + samsung,pins = "gpc1-2", "gpc1-3";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* usi_hsi2c_2 */
> + hsi2c2_bus: hsi2c2-bus {
> + samsung,pins = "gpc1-4", "gpc1-5";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* usi_spi_0 */
> + spi0_bus: spi0-bus {
> + samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi0_cs: spi0-cs {
> + samsung,pins = "gpp2-1";
> + samsung,pin-function = <1>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi0_cs_func: spi0-cs-func {
> + samsung,pins = "gpp2-1";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c0_bus: i2c0-bus {
> + samsung,pins = "gpp0-0", "gpp0-1";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c1_bus: i2c1-bus {
> + samsung,pins = "gpp0-2", "gpp0-3";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c2_bus: i2c2-bus {
> + samsung,pins = "gpp0-4", "gpp0-5";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c3_bus: i2c3-bus {
> + samsung,pins = "gpp1-0", "gpp1-1";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c4_bus: i2c4-bus {
> + samsung,pins = "gpp1-2", "gpp1-3";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +
> + fm_lna_en: fm-lna-en {
> + samsung,pins = "gpg2-3";
> + samsung,pin-function = <1>;
> + samsung,pin-pud = <0>;
> + samsung,pin-val = <0>;
> + };
> +
> + sensor_mclk0_in: sensor-mclk0-in {
> + samsung,pins = "gpc0-0";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk0_out: sensor-mclk0-out {
> + samsung,pins = "gpc0-0";
> + samsung,pin-function = <1>;
> + samsung,pin-pud = <1>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk0_fn: sensor-mclk0-fn {
No, seriously. What sensor is it? In SoC?
> + samsung,pins = "gpc0-0";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk1_in: sensor-mclk1-in {
> + samsung,pins = "gpc0-1";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk1_out: sensor-mclk1-out {
> + samsung,pins = "gpc0-1";
> + samsung,pin-function = <1>;
> + samsung,pin-pud = <1>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk1_fn: sensor-mclk1-fn {
> + samsung,pins = "gpc0-1";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk2_in: sensor-mclk2-in {
> + samsung,pins = "gpc0-2";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk2_out: sensor-mclk2-out {
> + samsung,pins = "gpc0-2";
> + samsung,pin-function = <1>;
> + samsung,pin-pud = <1>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sensor_mclk2_fn: sensor-mclk2-fn {
> + samsung,pins = "gpc0-2";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <2>;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/exynos/exynos850-usi.dtsi b/arch/arm64/boot/dts/exynos/exynos850-usi.dtsi
> new file mode 100644
> index 000000000000..fb243e0a6260
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850-usi.dtsi
> @@ -0,0 +1,30 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos850 SoC USI device tree source
> + *
> + * Copyright (C) 2019 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung's Exynos850 SoC USI channels are listed in this file as device tree
> + * nodes.
Why here not in exynos850.dtsi?
> + */
> +
> +#include <dt-bindings/clock/exynos850.h>
> +
> +/ {
> + aliases {
> + uart0 = &serial_0;
> + };
> +
> + /* USI_UART */
> + serial_0: uart@13820000 {
This should ne in soc node.
> + compatible = "samsung,exynos850-uart";
> + reg = <0x0 0x13820000 0x100>;
> + interrupts = <GIC_SPI INTREQ__UART IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_bus>;
> + clocks = <&clock GATE_UART_QCH>, <&clock DOUT_UART>;
> + clock-names = "gate_uart_clk0", "uart";
> + status = "disabled";
> + };
> +};
> diff --git a/arch/arm64/boot/dts/exynos/exynos850.dtsi b/arch/arm64/boot/dts/exynos/exynos850.dtsi
> new file mode 100644
> index 000000000000..ed2d1c8ae0c3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850.dtsi
> @@ -0,0 +1,245 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung Exynos850 SoC device tree source
> + *
> + * Copyright (C) 2018 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung Exynos850 SoC device nodes are listed in this file.
> + * Exynos based board files can include this file and provide
> + * values for board specific bindings.
> + */
> +
> +#include <dt-bindings/interrupt-controller/exynos850.h>
> +#include <dt-bindings/clock/exynos850.h>
> +#include "exynos850-pinctrl.dtsi"
> +#include "exynos850-usi.dtsi"
> +
> +/ {
Add a comment like:
/* Also known under engineering name exynos3830 */
> + compatible = "samsung,exynos850";
Undocumented compatible. Checkpatch should complain.
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + aliases {
> + pinctrl0 = &pinctrl_0;
> + pinctrl1 = &pinctrl_1;
> + pinctrl2 = &pinctrl_2;
> + pinctrl3 = &pinctrl_3;
> + pinctrl4 = &pinctrl_4;
> + pinctrl5 = &pinctrl_5;
> + };
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&cpu0>;
> + };
> + core1 {
> + cpu = <&cpu1>;
> + };
> + core2 {
> + cpu = <&cpu2>;
> + };
> + core3 {
> + cpu = <&cpu3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&cpu4>;
> + };
> + core1 {
> + cpu = <&cpu5>;
> + };
> + core2 {
> + cpu = <&cpu6>;
> + };
> + core3 {
> + cpu = <&cpu7>;
> + };
> + };
> + };
> +
> + cpu0: cpu@0000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0000>;
reg = <0x0 0x0>;
(in following places similarly)
> + enable-method = "psci";
> + };
> + cpu1: cpu@0001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0001>;
> + enable-method = "psci";
> + };
> + cpu2: cpu@0002 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0002>;
> + enable-method = "psci";
> + };
> + cpu3: cpu@0003 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0003>;
> + enable-method = "psci";
> + };
> + cpu4: cpu@0004 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0100>;
> + enable-method = "psci";
> + };
> + cpu5: cpu@0005 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0101>;
> + enable-method = "psci";
> + };
> + cpu6: cpu@0006 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0102>;
> + enable-method = "psci";
> + };
> + cpu7: cpu@0007 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x0 0x0103>;
> + enable-method = "psci";
> + };
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + gic: interrupt-controller@12a00000 {
> + compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
> + #interrupt-cells = <3>;
> + #address-cells = <0>;
> + interrupt-controller;
> + reg = <0x0 0x12a01000 0x1000>,
> + <0x0 0x12a02000 0x1000>,
> + <0x0 0x12a04000 0x2000>,
> + <0x0 0x12a06000 0x2000>;
> + interrupts = <GIC_PPI 9
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13
> + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14
> + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11
> + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10
> + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> + clock-frequency = <26000000>;
> + use-clocksource-only;
> + use-physical-timer;
> + };
> +
All below should be under soc node.
Please don't write new DTS/DTSI from scratch but use exynos5433.dtsi as
template/example.
> + clock: clock-controller@0x120e0000 {
> + compatible = "samsung,exynos850-clock";
> + reg = <0x0 0x120e0000 0x8000>;
> + #clock-cells = <1>;
> + };
> +
> + /* ALIVE */
> + pinctrl_0: pinctrl@11850000 {
> + compatible = "samsung,exynos850-pinctrl";
> + reg = <0x0 0x11850000 0x1000>;
> + interrupts = <GIC_SPI INTREQ__ALIVE_EINT0 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT1 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT2 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT5 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT6 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT7 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT9 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT10 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT13 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT15 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT16 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT17 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT18 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT19 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT20 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT21 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT22 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT23 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT24 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT25 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT26 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT27 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT28 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT29 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT30 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__ALIVE_EINT31 IRQ_TYPE_LEVEL_HIGH>;
> +
> + wakeup-interrupt-controller {
> + compatible = "samsung,exynos7-wakeup-eint";
> + };
> + };
> +
> + /* CMGP */
> + pinctrl_1: pinctrl@11c30000 {
> + compatible = "samsung,exynos850-pinctrl";
> + reg = <0x0 0x11c30000 0x1000>;
> + interrupts =
> + <GIC_SPI INTREQ__CMGP_EXT_INTM00 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__CMGP_EXT_INTM01 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__CMGP_EXT_INTM02 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__CMGP_EXT_INTM03 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__CMGP_EXT_INTM04 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__CMGP_EXT_INTM05 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__CMGP_EXT_INTM06 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI INTREQ__CMGP_EXT_INTM07 IRQ_TYPE_LEVEL_HIGH>;
> +
> + wakeup-interrupt-controller {
> + compatible = "samsung,exynos7-wakeup-eint";
> + };
> + };
> +
> + /* AUD */
> + pinctrl_2: pinctrl@14a60000 {
> + compatible = "samsung,exynos850-pinctrl";
> + reg = <0x0 0x14a60000 0x1000>;
> + };
> +
> + /* HSI */
> + pinctrl_3: pinctrl@13430000 {
> + compatible = "samsung,exynos850-pinctrl";
> + reg = <0x0 0x13430000 0x1000>;
> + interrupts = <GIC_SPI INTREQ__GPIO_HSI IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* CORE */
> + pinctrl_4: pinctrl@12070000 {
> + compatible = "samsung,exynos850-pinctrl";
> + reg = <0x0 0x12070000 0x1000>;
> + interrupts = <GIC_SPI INTREQ__GPIO_CORE IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* PERI */
> + pinctrl_5: pinctrl@139b0000 {
> + compatible = "samsung,exynos850-pinctrl";
> + reg = <0x0 0x139b0000 0x1000>;
> + interrupts = <GIC_SPI INTREQ__GPIO_PERI IRQ_TYPE_LEVEL_HIGH>;
> + };
> +};
>
Best regards,
Krzysztof
