This provides the configuration for the currently available evaluation boards PCB134 and PCB135. The series depends on the following series currently on its way into the kernel: - Sparx5 Reset Driver Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@xxxxxxxxxxxxx/ Signed-off-by: Steen Hegelund <steen.hegelund@xxxxxxxxxxxxx> Signed-off-by: Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx> Signed-off-by: Bjarni Jonasson <bjarni.jonasson@xxxxxxxxxxxxx> --- arch/arm64/boot/dts/microchip/sparx5.dtsi | 94 ++- .../dts/microchip/sparx5_pcb134_board.dtsi | 481 ++++++++++++-- .../dts/microchip/sparx5_pcb135_board.dtsi | 621 +++++++++++++++++- 3 files changed, 1112 insertions(+), 84 deletions(-) diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi index d64621d1213b..ad07fff40544 100644 --- a/arch/arm64/boot/dts/microchip/sparx5.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi @@ -135,9 +135,12 @@ mux: mux-controller { }; }; - reset@611010008 { - compatible = "microchip,sparx5-chip-reset"; + reset: reset-controller@611010008 { + compatible = "microchip,sparx5-switch-reset"; reg = <0x6 0x11010008 0x4>; + reg-names = "gcb"; + #reset-cells = <1>; + cpu-syscon = <&cpu_ctrl>; }; uart0: serial@600100000 { @@ -275,6 +278,21 @@ emmc_pins: emmc-pins { "GPIO_46", "GPIO_47"; function = "emmc"; }; + + miim1_pins: miim1-pins { + pins = "GPIO_56", "GPIO_57"; + function = "miim"; + }; + + miim2_pins: miim2-pins { + pins = "GPIO_58", "GPIO_59"; + function = "miim"; + }; + + miim3_pins: miim3-pins { + pins = "GPIO_52", "GPIO_53"; + function = "miim"; + }; }; sgpio0: gpio@61101036c { @@ -285,6 +303,8 @@ sgpio0: gpio@61101036c { clocks = <&sys_clk>; pinctrl-0 = <&sgpio0_pins>; pinctrl-names = "default"; + resets = <&reset 0>; + reset-names = "switch"; reg = <0x6 0x1101036c 0x100>; sgpio_in0: gpio@0 { compatible = "microchip,sparx5-sgpio-bank"; @@ -292,6 +312,9 @@ sgpio_in0: gpio@0 { gpio-controller; #gpio-cells = <3>; ngpios = <96>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; }; sgpio_out0: gpio@1 { compatible = "microchip,sparx5-sgpio-bank"; @@ -310,6 +333,8 @@ sgpio1: gpio@611010484 { clocks = <&sys_clk>; pinctrl-0 = <&sgpio1_pins>; pinctrl-names = "default"; + resets = <&reset 0>; + reset-names = "switch"; reg = <0x6 0x11010484 0x100>; sgpio_in1: gpio@0 { compatible = "microchip,sparx5-sgpio-bank"; @@ -317,6 +342,9 @@ sgpio_in1: gpio@0 { gpio-controller; #gpio-cells = <3>; ngpios = <96>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; }; sgpio_out1: gpio@1 { compatible = "microchip,sparx5-sgpio-bank"; @@ -335,6 +363,8 @@ sgpio2: gpio@61101059c { clocks = <&sys_clk>; pinctrl-0 = <&sgpio2_pins>; pinctrl-names = "default"; + resets = <&reset 0>; + reset-names = "switch"; reg = <0x6 0x1101059c 0x100>; sgpio_in2: gpio@0 { reg = <0>; @@ -342,6 +372,9 @@ sgpio_in2: gpio@0 { gpio-controller; #gpio-cells = <3>; ngpios = <96>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; }; sgpio_out2: gpio@1 { compatible = "microchip,sparx5-sgpio-bank"; @@ -386,5 +419,62 @@ tmon0: tmon@610508110 { #thermal-sensor-cells = <0>; clocks = <&ahb_clk>; }; + + mdio0: mdio@6110102b0 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102b0 0x24>; + }; + + mdio1: mdio@6110102d4 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim1_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio2: mdio@6110102f8 { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim2_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x110102d4 0x24>; + }; + + mdio3: mdio@61101031c { + compatible = "mscc,ocelot-miim"; + status = "disabled"; + pinctrl-0 = <&miim3_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x6 0x1101031c 0x24>; + }; + + serdes: serdes@10808000 { + compatible = "microchip,sparx5-serdes"; + #phy-cells = <1>; + clocks = <&sys_clk>; + reg = <0x6 0x10808000 0x5d0000>; + }; + + switch: switch@0x600000000 { + compatible = "microchip,sparx5-switch"; + reg = <0x6 0 0x401000>, + <0x6 0x10004000 0x7fc000>, + <0x6 0x11010000 0xaf0000>; + reg-names = "cpu", "dev", "gcb"; + interrupt-names = "xtr"; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + resets = <&reset 0>; + reset-names = "switch"; + }; }; }; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi index f0c915160990..33faf1f3264f 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi @@ -7,30 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c100 = &i2c100; - i2c101 = &i2c101; - i2c102 = &i2c102; - i2c103 = &i2c103; - i2c104 = &i2c104; - i2c105 = &i2c105; - i2c106 = &i2c106; - i2c107 = &i2c107; - i2c108 = &i2c108; - i2c109 = &i2c109; - i2c110 = &i2c110; - i2c111 = &i2c111; - i2c112 = &i2c112; - i2c113 = &i2c113; - i2c114 = &i2c114; - i2c115 = &i2c115; - i2c116 = &i2c116; - i2c117 = &i2c117; - i2c118 = &i2c118; - i2c119 = &i2c119; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -298,17 +274,10 @@ gpio@1 { &spi0 { status = "okay"; - spi@0 { - compatible = "spi-mux"; - mux-controls = <&mux>; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; /* CS0 */ - spi-flash@9 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <8000000>; - reg = <0x9>; /* SPI */ - }; + spi-flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <8000000>; + reg = <0>; }; }; @@ -328,6 +297,33 @@ spi-flash@9 { }; }; +&sgpio0 { + status = "okay"; + microchip,sgpio-port-ranges = <8 15>; + gpio@0 { + ngpios = <64>; + }; + gpio@1 { + ngpios = <64>; + }; +}; + +&sgpio1 { + status = "okay"; + microchip,sgpio-port-ranges = <24 31>; + gpio@0 { + ngpios = <64>; + }; + gpio@1 { + ngpios = <64>; + }; +}; + +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <11 31>; +}; + &gpio { i2cmux_pins_i: i2cmux-pins-i { pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19", @@ -415,9 +411,9 @@ i2c0_emux: i2c0-emux@0 { &i2c0_imux { pinctrl-names = - "i2c100", "i2c101", "i2c102", "i2c103", - "i2c104", "i2c105", "i2c106", "i2c107", - "i2c108", "i2c109", "i2c110", "i2c111", "idle"; + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", + "i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8", + "i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle"; pinctrl-0 = <&i2cmux_0>; pinctrl-1 = <&i2cmux_1>; pinctrl-2 = <&i2cmux_2>; @@ -431,62 +427,62 @@ &i2c0_imux { pinctrl-10 = <&i2cmux_10>; pinctrl-11 = <&i2cmux_11>; pinctrl-12 = <&i2cmux_pins_i>; - i2c100: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c101: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c102: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c103: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c104: i2c_sfp5 { + i2c_sfp5: i2c_sfp5 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c105: i2c_sfp6 { + i2c_sfp6: i2c_sfp6 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c106: i2c_sfp7 { + i2c_sfp7: i2c_sfp7 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c107: i2c_sfp8 { + i2c_sfp8: i2c_sfp8 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; - i2c108: i2c_sfp9 { + i2c_sfp9: i2c_sfp9 { reg = <0x8>; #address-cells = <1>; #size-cells = <0>; }; - i2c109: i2c_sfp10 { + i2c_sfp10: i2c_sfp10 { reg = <0x9>; #address-cells = <1>; #size-cells = <0>; }; - i2c110: i2c_sfp11 { + i2c_sfp11: i2c_sfp11 { reg = <0xa>; #address-cells = <1>; #size-cells = <0>; }; - i2c111: i2c_sfp12 { + i2c_sfp12: i2c_sfp12 { reg = <0xb>; #address-cells = <1>; #size-cells = <0>; @@ -499,44 +495,413 @@ &gpio 60 GPIO_ACTIVE_HIGH &gpio 61 GPIO_ACTIVE_HIGH &gpio 54 GPIO_ACTIVE_HIGH>; idle-state = <0x8>; - i2c112: i2c_sfp13 { + i2c_sfp13: i2c_sfp13 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c113: i2c_sfp14 { + i2c_sfp14: i2c_sfp14 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c114: i2c_sfp15 { + i2c_sfp15: i2c_sfp15 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c115: i2c_sfp16 { + i2c_sfp16: i2c_sfp16 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; - i2c116: i2c_sfp17 { + i2c_sfp17: i2c_sfp17 { reg = <0x4>; #address-cells = <1>; #size-cells = <0>; }; - i2c117: i2c_sfp18 { + i2c_sfp18: i2c_sfp18 { reg = <0x5>; #address-cells = <1>; #size-cells = <0>; }; - i2c118: i2c_sfp19 { + i2c_sfp19: i2c_sfp19 { reg = <0x6>; #address-cells = <1>; #size-cells = <0>; }; - i2c119: i2c_sfp20 { + i2c_sfp20: i2c_sfp20 { reg = <0x7>; #address-cells = <1>; #size-cells = <0>; }; }; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&axi { + sfp_eth12: sfp-eth12 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth13: sfp-eth13 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth14: sfp-eth14 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth15: sfp-eth15 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth48: sfp-eth48 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp5>; + tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth49: sfp-eth49 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp6>; + tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth50: sfp-eth50 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp7>; + tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth51: sfp-eth51 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp8>; + tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth52: sfp-eth52 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp9>; + tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth53: sfp-eth53 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp10>; + tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth54: sfp-eth54 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp11>; + tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth55: sfp-eth55 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp12>; + tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth56: sfp-eth56 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp13>; + tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth57: sfp-eth57 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp14>; + tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth58: sfp-eth58 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp15>; + tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth59: sfp-eth59 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp16>; + tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp17>; + tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp18>; + tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp19>; + tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp20>; + tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>; + los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 10G SFPs */ + port12: port@12 { + reg = <12>; + microchip,bandwidth = <10000>; + phys = <&serdes 13>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth12>; + microchip,sd-sgpio = <301>; + managed = "in-band-status"; + }; + port13: port@13 { + reg = <13>; + /* Example: CU SFP, 1G speed */ + microchip,bandwidth = <10000>; + phys = <&serdes 14>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth13>; + microchip,sd-sgpio = <305>; + managed = "in-band-status"; + }; + port14: port@14 { + reg = <14>; + microchip,bandwidth = <10000>; + phys = <&serdes 15>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth14>; + microchip,sd-sgpio = <309>; + managed = "in-band-status"; + }; + port15: port@15 { + reg = <15>; + microchip,bandwidth = <10000>; + phys = <&serdes 16>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth15>; + microchip,sd-sgpio = <313>; + managed = "in-band-status"; + }; + port48: port@48 { + reg = <48>; + microchip,bandwidth = <10000>; + phys = <&serdes 17>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth48>; + microchip,sd-sgpio = <317>; + managed = "in-band-status"; + }; + port49: port@49 { + reg = <49>; + microchip,bandwidth = <10000>; + phys = <&serdes 18>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth49>; + microchip,sd-sgpio = <321>; + managed = "in-band-status"; + }; + port50: port@50 { + reg = <50>; + microchip,bandwidth = <10000>; + phys = <&serdes 19>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth50>; + microchip,sd-sgpio = <325>; + managed = "in-band-status"; + }; + port51: port@51 { + reg = <51>; + microchip,bandwidth = <10000>; + phys = <&serdes 20>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth51>; + microchip,sd-sgpio = <329>; + managed = "in-band-status"; + }; + port52: port@52 { + reg = <52>; + microchip,bandwidth = <10000>; + phys = <&serdes 21>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth52>; + microchip,sd-sgpio = <333>; + managed = "in-band-status"; + }; + port53: port@53 { + reg = <53>; + microchip,bandwidth = <10000>; + phys = <&serdes 22>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth53>; + microchip,sd-sgpio = <337>; + managed = "in-band-status"; + }; + port54: port@54 { + reg = <54>; + microchip,bandwidth = <10000>; + phys = <&serdes 23>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth54>; + microchip,sd-sgpio = <341>; + managed = "in-band-status"; + }; + port55: port@55 { + reg = <55>; + microchip,bandwidth = <10000>; + phys = <&serdes 24>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth55>; + microchip,sd-sgpio = <345>; + managed = "in-band-status"; + }; + /* 25G SFPs */ + port56: port@56 { + reg = <56>; + microchip,bandwidth = <10000>; + phys = <&serdes 25>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth56>; + microchip,sd-sgpio = <349>; + managed = "in-band-status"; + }; + port57: port@57 { + reg = <57>; + microchip,bandwidth = <10000>; + phys = <&serdes 26>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth57>; + microchip,sd-sgpio = <353>; + managed = "in-band-status"; + }; + port58: port@58 { + reg = <58>; + microchip,bandwidth = <10000>; + phys = <&serdes 27>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth58>; + microchip,sd-sgpio = <357>; + managed = "in-band-status"; + }; + port59: port@59 { + reg = <59>; + microchip,bandwidth = <10000>; + phys = <&serdes 28>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth59>; + microchip,sd-sgpio = <361>; + managed = "in-band-status"; + }; + port60: port@60 { + reg = <60>; + microchip,bandwidth = <10000>; + phys = <&serdes 29>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth60>; + microchip,sd-sgpio = <365>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + microchip,bandwidth = <10000>; + phys = <&serdes 30>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth61>; + microchip,sd-sgpio = <369>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + microchip,bandwidth = <10000>; + phys = <&serdes 31>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth62>; + microchip,sd-sgpio = <373>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + microchip,bandwidth = <10000>; + phys = <&serdes 32>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth63>; + microchip,sd-sgpio = <377>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + microchip,bandwidth = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi index e28c6dd16377..ef96e6d8c6b3 100644 --- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi +++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi @@ -7,14 +7,6 @@ #include "sparx5_pcb_common.dtsi" /{ - aliases { - i2c0 = &i2c0; - i2c152 = &i2c152; - i2c153 = &i2c153; - i2c154 = &i2c154; - i2c155 = &i2c155; - }; - gpio-restart { compatible = "gpio-restart"; gpios = <&gpio 37 GPIO_ACTIVE_LOW>; @@ -97,17 +89,10 @@ i2cmux_s32: i2cmux-3 { &spi0 { status = "okay"; - spi@0 { - compatible = "spi-mux"; - mux-controls = <&mux>; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; /* CS0 */ - spi-flash@9 { - compatible = "jedec,spi-nor"; - spi-max-frequency = <8000000>; - reg = <0x9>; /* SPI */ - }; + spi-flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <8000000>; + reg = <0>; }; }; @@ -138,6 +123,11 @@ gpio@1 { }; }; +&sgpio2 { + status = "okay"; + microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>; +}; + &axi { i2c0_imux: i2c0-imux@0 { compatible = "i2c-mux-pinctrl"; @@ -149,31 +139,614 @@ i2c0_imux: i2c0-imux@0 { &i2c0_imux { pinctrl-names = - "i2c152", "i2c153", "i2c154", "i2c155", + "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4", "idle"; pinctrl-0 = <&i2cmux_s29>; pinctrl-1 = <&i2cmux_s30>; pinctrl-2 = <&i2cmux_s31>; pinctrl-3 = <&i2cmux_s32>; pinctrl-4 = <&i2cmux_pins_i>; - i2c152: i2c_sfp1 { + i2c_sfp1: i2c_sfp1 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; - i2c153: i2c_sfp2 { + i2c_sfp2: i2c_sfp2 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; - i2c154: i2c_sfp3 { + i2c_sfp3: i2c_sfp3 { reg = <0x2>; #address-cells = <1>; #size-cells = <0>; }; - i2c155: i2c_sfp4 { + i2c_sfp4: i2c_sfp4 { reg = <0x3>; #address-cells = <1>; #size-cells = <0>; }; }; + +&axi { + sfp_eth60: sfp-eth60 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth61: sfp-eth61 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth62: sfp-eth62 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp3>; + tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>; + }; + sfp_eth63: sfp-eth63 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp4>; + tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>; + los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>; + tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>; + }; +}; + +&mdio0 { + status = "ok"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + }; + phy5: ethernet-phy@5 { + reg = <5>; + }; + phy6: ethernet-phy@6 { + reg = <6>; + }; + phy7: ethernet-phy@7 { + reg = <7>; + }; + phy8: ethernet-phy@8 { + reg = <8>; + }; + phy9: ethernet-phy@9 { + reg = <9>; + }; + phy10: ethernet-phy@10 { + reg = <10>; + }; + phy11: ethernet-phy@11 { + reg = <11>; + }; + phy12: ethernet-phy@12 { + reg = <12>; + }; + phy13: ethernet-phy@13 { + reg = <13>; + }; + phy14: ethernet-phy@14 { + reg = <14>; + }; + phy15: ethernet-phy@15 { + reg = <15>; + }; + phy16: ethernet-phy@16 { + reg = <16>; + }; + phy17: ethernet-phy@17 { + reg = <17>; + }; + phy18: ethernet-phy@18 { + reg = <18>; + }; + phy19: ethernet-phy@19 { + reg = <19>; + }; + phy20: ethernet-phy@20 { + reg = <20>; + }; + phy21: ethernet-phy@21 { + reg = <21>; + }; + phy22: ethernet-phy@22 { + reg = <22>; + }; + phy23: ethernet-phy@23 { + reg = <23>; + }; +}; + +&mdio1 { + status = "ok"; + phy24: ethernet-phy@24 { + reg = <0>; + }; + phy25: ethernet-phy@25 { + reg = <1>; + }; + phy26: ethernet-phy@26 { + reg = <2>; + }; + phy27: ethernet-phy@27 { + reg = <3>; + }; + phy28: ethernet-phy@28 { + reg = <4>; + }; + phy29: ethernet-phy@29 { + reg = <5>; + }; + phy30: ethernet-phy@30 { + reg = <6>; + }; + phy31: ethernet-phy@31 { + reg = <7>; + }; + phy32: ethernet-phy@32 { + reg = <8>; + }; + phy33: ethernet-phy@33 { + reg = <9>; + }; + phy34: ethernet-phy@34 { + reg = <10>; + }; + phy35: ethernet-phy@35 { + reg = <11>; + }; + phy36: ethernet-phy@36 { + reg = <12>; + }; + phy37: ethernet-phy@37 { + reg = <13>; + }; + phy38: ethernet-phy@38 { + reg = <14>; + }; + phy39: ethernet-phy@39 { + reg = <15>; + }; + phy40: ethernet-phy@40 { + reg = <16>; + }; + phy41: ethernet-phy@41 { + reg = <17>; + }; + phy42: ethernet-phy@42 { + reg = <18>; + }; + phy43: ethernet-phy@43 { + reg = <19>; + }; + phy44: ethernet-phy@44 { + reg = <20>; + }; + phy45: ethernet-phy@45 { + reg = <21>; + }; + phy46: ethernet-phy@46 { + reg = <22>; + }; + phy47: ethernet-phy@47 { + reg = <23>; + }; +}; + +&mdio3 { + status = "ok"; + phy64: ethernet-phy@64 { + reg = <28>; + }; +}; + +&switch { + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy0>; + phy-mode = "qsgmii"; + }; + port1: port@1 { + reg = <1>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy1>; + phy-mode = "qsgmii"; + }; + port2: port@2 { + reg = <2>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy2>; + phy-mode = "qsgmii"; + }; + port3: port@3 { + reg = <3>; + microchip,bandwidth = <1000>; + phys = <&serdes 13>; + phy-handle = <&phy3>; + phy-mode = "qsgmii"; + }; + port4: port@4 { + reg = <4>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy4>; + phy-mode = "qsgmii"; + }; + port5: port@5 { + reg = <5>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy5>; + phy-mode = "qsgmii"; + }; + port6: port@6 { + reg = <6>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy6>; + phy-mode = "qsgmii"; + }; + port7: port@7 { + reg = <7>; + microchip,bandwidth = <1000>; + phys = <&serdes 14>; + phy-handle = <&phy7>; + phy-mode = "qsgmii"; + }; + port8: port@8 { + reg = <8>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy8>; + phy-mode = "qsgmii"; + }; + port9: port@9 { + reg = <9>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy9>; + phy-mode = "qsgmii"; + }; + port10: port@10 { + reg = <10>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy10>; + phy-mode = "qsgmii"; + }; + port11: port@11 { + reg = <11>; + microchip,bandwidth = <1000>; + phys = <&serdes 15>; + phy-handle = <&phy11>; + phy-mode = "qsgmii"; + }; + port12: port@12 { + reg = <12>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy12>; + phy-mode = "qsgmii"; + }; + port13: port@13 { + reg = <13>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy13>; + phy-mode = "qsgmii"; + }; + port14: port@14 { + reg = <14>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy14>; + phy-mode = "qsgmii"; + }; + port15: port@15 { + reg = <15>; + microchip,bandwidth = <1000>; + phys = <&serdes 16>; + phy-handle = <&phy15>; + phy-mode = "qsgmii"; + }; + port16: port@16 { + reg = <16>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy16>; + phy-mode = "qsgmii"; + }; + port17: port@17 { + reg = <17>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy17>; + phy-mode = "qsgmii"; + }; + port18: port@18 { + reg = <18>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy18>; + phy-mode = "qsgmii"; + }; + port19: port@19 { + reg = <19>; + microchip,bandwidth = <1000>; + phys = <&serdes 17>; + phy-handle = <&phy19>; + phy-mode = "qsgmii"; + }; + port20: port@20 { + reg = <20>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy20>; + phy-mode = "qsgmii"; + }; + port21: port@21 { + reg = <21>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy21>; + phy-mode = "qsgmii"; + }; + port22: port@22 { + reg = <22>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy22>; + phy-mode = "qsgmii"; + }; + port23: port@23 { + reg = <23>; + microchip,bandwidth = <1000>; + phys = <&serdes 18>; + phy-handle = <&phy23>; + phy-mode = "qsgmii"; + }; + port24: port@24 { + reg = <24>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy24>; + phy-mode = "qsgmii"; + }; + port25: port@25 { + reg = <25>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy25>; + phy-mode = "qsgmii"; + }; + port26: port@26 { + reg = <26>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy26>; + phy-mode = "qsgmii"; + }; + port27: port@27 { + reg = <27>; + microchip,bandwidth = <1000>; + phys = <&serdes 19>; + phy-handle = <&phy27>; + phy-mode = "qsgmii"; + }; + port28: port@28 { + reg = <28>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy28>; + phy-mode = "qsgmii"; + }; + port29: port@29 { + reg = <29>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy29>; + phy-mode = "qsgmii"; + }; + port30: port@30 { + reg = <30>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy30>; + phy-mode = "qsgmii"; + }; + port31: port@31 { + reg = <31>; + microchip,bandwidth = <1000>; + phys = <&serdes 20>; + phy-handle = <&phy31>; + phy-mode = "qsgmii"; + }; + port32: port@32 { + reg = <32>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy32>; + phy-mode = "qsgmii"; + }; + port33: port@33 { + reg = <33>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy33>; + phy-mode = "qsgmii"; + }; + port34: port@34 { + reg = <34>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy34>; + phy-mode = "qsgmii"; + }; + port35: port@35 { + reg = <35>; + microchip,bandwidth = <1000>; + phys = <&serdes 21>; + phy-handle = <&phy35>; + phy-mode = "qsgmii"; + }; + port36: port@36 { + reg = <36>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy36>; + phy-mode = "qsgmii"; + }; + port37: port@37 { + reg = <37>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy37>; + phy-mode = "qsgmii"; + }; + port38: port@38 { + reg = <38>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy38>; + phy-mode = "qsgmii"; + }; + port39: port@39 { + reg = <39>; + microchip,bandwidth = <1000>; + phys = <&serdes 22>; + phy-handle = <&phy39>; + phy-mode = "qsgmii"; + }; + port40: port@40 { + reg = <40>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy40>; + phy-mode = "qsgmii"; + }; + port41: port@41 { + reg = <41>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy41>; + phy-mode = "qsgmii"; + }; + port42: port@42 { + reg = <42>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy42>; + phy-mode = "qsgmii"; + }; + port43: port@43 { + reg = <43>; + microchip,bandwidth = <1000>; + phys = <&serdes 23>; + phy-handle = <&phy43>; + phy-mode = "qsgmii"; + }; + port44: port@44 { + reg = <44>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy44>; + phy-mode = "qsgmii"; + }; + port45: port@45 { + reg = <45>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy45>; + phy-mode = "qsgmii"; + }; + port46: port@46 { + reg = <46>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy46>; + phy-mode = "qsgmii"; + }; + port47: port@47 { + reg = <47>; + microchip,bandwidth = <1000>; + phys = <&serdes 24>; + phy-handle = <&phy47>; + phy-mode = "qsgmii"; + }; + /* Then the 25G interfaces */ + port60: port@60 { + reg = <60>; + microchip,bandwidth = <25000>; + phys = <&serdes 29>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth60>; + managed = "in-band-status"; + }; + port61: port@61 { + reg = <61>; + microchip,bandwidth = <25000>; + phys = <&serdes 30>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth61>; + managed = "in-band-status"; + }; + port62: port@62 { + reg = <62>; + microchip,bandwidth = <25000>; + phys = <&serdes 31>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth62>; + managed = "in-band-status"; + }; + port63: port@63 { + reg = <63>; + microchip,bandwidth = <25000>; + phys = <&serdes 32>; + phy-mode = "10gbase-r"; + sfp = <&sfp_eth63>; + managed = "in-band-status"; + }; + /* Finally the Management interface */ + port64: port@64 { + reg = <64>; + microchip,bandwidth = <1000>; + phys = <&serdes 0>; + phy-handle = <&phy64>; + phy-mode = "sgmii"; + }; + }; +}; -- 2.31.1
