Re: [PATCH v4 1/4] dt-bindings: i2c: aspeed: add transfer mode support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Ping.

On 3/10/2021 7:55 AM, Jae Hyun Yoo wrote:
On 3/9/2021 6:15 PM, Rob Herring wrote:
On Tue, Mar 9, 2021 at 10:02 AM Jae Hyun Yoo
<jae.hyun.yoo@xxxxxxxxxxxxxxx> wrote:

Hi Rob,

On 3/6/2021 12:30 PM, Rob Herring wrote:
On Wed, Feb 24, 2021 at 11:17:17AM -0800, Jae Hyun Yoo wrote:
Append bindings to support transfer mode.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>
Reviewed-by: Brendan Higgins <brendanhiggins@xxxxxxxxxx>
---
Changes since v3:
- None

Changes since v2:
- Moved SRAM resources back to default dtsi and added mode selection
    property.

Changes since v1:
- Removed buffer reg settings from default device tree and added the settings
    into here to show the predefined buffer range per each bus.

   .../devicetree/bindings/i2c/i2c-aspeed.txt    | 37 +++++++++++++++----
   1 file changed, 30 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
index b47f6ccb196a..242343177324 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
@@ -17,6 +17,20 @@ Optional Properties:
   - bus-frequency    : frequency of the bus clock in Hz defaults to 100 kHz when not
                specified
   - multi-master     : states that there is another master active on this bus. +- aspeed,i2c-xfer-mode      : should be "byte", "buf" or "dma" to select transfer +                      mode defaults to "byte" mode when not specified.
+
+                      I2C DMA mode on AST2500 has these restrictions:
+                        - If one of these controllers is enabled
+                            * UHCI host controller
+                            * MCTP controller
+                          I2C has to use buffer mode or byte mode instead +                          since these controllers run only in DMA mode and
+                          I2C is sharing the same DMA H/W with them.
+                        - If one of these controllers uses DMA mode, I2C
+                          can't use DMA mode
+                            * SD/eMMC
+                            * Port80 snoop

How does one decide between byte or buf mode?

If a given system makes just one byte r/w transactions most of the time
then byte mode will be a right setting. Otherwise, buf mode is more
efficient because it doesn't generate a bunch of interrupts on every
byte handling.

Then why doesn't the driver do byte transactions when it gets small
1-4? byte transactions and buffer transactions when it gets larger
sized transactions.

Good question and it could be an option of this implementation.
Actually, each mode needs different register handling so we need to add
additional conditional branches to make it dynamic mode change depends
on the data size which can be a downside. Also, checked that small
amount of data transfer efficiency in 'buf' transfer mode is almost same
to 'byte' mode so there would be no big benefit from the dynamic mode
change. Of course, we can remove the 'byte' transfer mode but we should
also provide flexibility of configuration on what this hardware can
support, IMO.

Thanks,
Jae



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux