This patch series adds devicetree support for the Forlinx FETA40i-C SoM
and OKA40i-C carrier board/devboard.
The FETA40i-C is an "industrial/automotive" SoM by Forlinx.
SoM specs:
- SoC: R40 or A40i
- PMIC: AXP221S
- RAM: 1GiB/2GiB DDR3 (dual-rank)
- eMMC: 8GB,
- Mates with carrier board via four 80-pin connectors (AXK6F80337YG).
OKA40i-C is a carrier board by the same manufacturer for this SoM,
whose main purpose is as a development board with a variety of
peripherals:
- Power: DC5V barrel or USB OTG or 4.2V Lipo battery
- Video out: HDMI, TV out, LVDS
- WiFi+Bluetooth: RL-UM02WBS-8723BU-V1.2 (802.11 b/g/n, BT V2.1/3.0/4.0)
- Ethernet: 10/100Mbps
- Storage: µSD, fullsize SD, eMMC (on SoM), SATA
- USB: 3 x USB2.0 Host (2 via hub, 1 native), 1 x USB2.0 OTG (micro-B)
- UART: RS232, RS485, 4 3.3v uarts (of which 2 have RTS/CTS)
- Other I/O: SPI x2, TWI, SDIO header, GPIO header, JTAG header
- Mini PCIe slot with sim holder for WLAN modem
- Smart card holder
- RTC (RX8010SJ)
- Two user LEDs
- Three user buttons (via KeyADC).
Of the board features listed above, support for the following has *NOT*
been tested:
- TV out & LVDS
- SATA
- Smart cards
- KeyADC buttons (no support)
The series consists of five patches, with dependencies as follows:
* Patch 4 depends on patch 3;
* Patch 5 depends on patches 2&4.
The rest are independent, however patch 2 may refuse to apply
without patch 1.
Signed-off-by: Ivan Uvarov <i.uvarov@xxxxxxxxxxxxxxxxxx>
---
Changelog:
v4:
* split dt-bindings patch into separate parts for vendor and device
* add /omit-if-no-ref/ to the mmc3 pins node as well
* add clarifying comment on the naming of user led nodes
v3:
* add compatible string for the SoM
* move regulators aldo3, dcdc{2,3,5}, eldo{2,3} to the SoM .dtsi
v2:
* split patch into series
* edits to sun8i-r40.dtsi are now in separate patch
* add dt bindings for compatible strings (in separate patch)
* add /omit-if-no-ref/ to the new uart pin nodes
* preliminary patch adds the keyword to existing nodes for UART0 & UART3
* whitespace fixes as suggested by checkpatch.pl
(draft2 ->) v1:
* fix indentation from spaces to tabs
* remove commented properties and other extraneous comments
* enable uarts 2,4,5&7 and alias uart3
* update the user-LED bindings
* remove mmc1 & add mmc3 binding
* bring together the max/min microvolts on three regulators
* The reported 2.5v value in ALDO2 comes from U-Boot, where apparently
this is the KConfig default for this regulator. The correct voltage
is 1.8v.
* remove extraneous `always-on`s from regulators dldo1 and eldo2/3
* remove reg_dldo3 node entirely
---
Ivan Uvarov (5):
ARM: dts: sun8i: r40: add /omit-if-no-ref/ to pinmux nodes for UARTs 0&3
ARM: dts: sun8i: r40: add pinmux settings for MMC3 and UARTs 2,4,5&7
dt-bindings: add compatible vendor prefix for Forlinx
dt-bindings: arm: add compatible for Forlinx OKA40i-C and FETA40i-C
ARM: dts: sun8i: r40: add devicetree for Forlinx FETA40i-C & OKA40i-C
.../devicetree/bindings/arm/sunxi.yaml | 6 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-r40-feta40i.dtsi | 106 +++++++++
arch/arm/boot/dts/sun8i-r40-oka40i-c.dts | 203 ++++++++++++++++++
arch/arm/boot/dts/sun8i-r40.dtsi | 44 ++++
6 files changed, 362 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r40-feta40i.dtsi
create mode 100644 arch/arm/boot/dts/sun8i-r40-oka40i-c.dts
--
2.25.1
