UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1]. Add support by removing the no-1-8-v tag and including the voltage regulator device tree nodes for power cycling. [1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1 Signed-off-by: Aswath Govindraju <a-govindraju@xxxxxx> --- test logs: https://pastebin.ubuntu.com/p/vpYbY9QWh8/ arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 1 - .../arm64/boot/dts/ti/k3-am654-base-board.dts | 33 +++++++++++++++++++ 2 files changed, 33 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi index cb340d1b401f..632f32fce4a1 100644 --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi @@ -301,7 +301,6 @@ ti,otap-del-sel = <0x2>; ti,trm-icp = <0x8>; dma-coherent; - no-1-8-v; }; scm_conf: scm-conf@100000 { diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts index 9e87fb313a54..6f7292b6fe0a 100644 --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts @@ -91,6 +91,38 @@ #clock-cells = <0>; clock-frequency = <24000000>; }; + + evm_12v0: fixedregulator-evm12v0 { + /* main supply */ + compatible = "regulator-fixed"; + regulator-name = "evm_12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc3v3_io: fixedregulator-vcc3v3io { + /* Output of TPS54334 */ + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&evm_12v0>; + }; + + vdd_mmc1_sd: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + vin-supply = <&vcc3v3_io>; + gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>; + }; }; &wkup_pmx0 { @@ -350,6 +382,7 @@ * disable sdhci1 */ &sdhci1 { + vmmc-supply = <&vdd_mmc1_sd>; pinctrl-names = "default"; pinctrl-0 = <&main_mmc1_pins_default>; ti,driver-strength-ohm = <50>; -- 2.17.1
