Hi Rob,
Thank you for the review comments...
On 30/10/2020 11:18 pm, Rob Herring wrote:
On Fri, Oct 30, 2020 at 01:31:52PM +0800, Ramuthevar,Vadivel MuruganX wrote:
From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
---
.../devicetree/bindings/spi/cadence-quadspi.txt | 67 ---------
.../devicetree/bindings/spi/cadence-quadspi.yaml | 149 +++++++++++++++++++++
2 files changed, 149 insertions(+), 67 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
deleted file mode 100644
index 945be7d5b236..000000000000
--- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
- Generic default - "cdns,qspi-nor".
- For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
- For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
- physical address and length. The first entry is the address and
- length of the controller register set. The second entry is the
- address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
- the read data rather than the QSPI clock. Make sure that QSPI return
- clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
- mode chip select outputs are de-asserted between
- transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
- de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
- transaction and deasserting the device chip select
- (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
- and first bit transfer.
-- resets : Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names : Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
- qspi: spi@ff705000 {
- compatible = "cdns,qspi-nor";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0xff705000 0x1000>,
- <0xffa00000 0x1000>;
- interrupts = <0 151 4>;
- clocks = <&qspi_clk>;
- cdns,is-decoded-cs;
- cdns,fifo-depth = <128>;
- cdns,fifo-width = <4>;
- cdns,trigger-address = <0x00000000>;
- resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
- reset-names = "qspi", "qspi-ocp";
-
- flash0: n25q00@0 {
- ...
- cdns,read-delay = <4>;
- cdns,tshsl-ns = <50>;
- cdns,tsd2d-ns = <50>;
- cdns,tchsh-ns = <4>;
- cdns,tslch-ns = <4>;
- };
- };
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
new file mode 100644
index 000000000000..ec22b040d804
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
@@ -0,0 +1,149 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence Quad SPI controller
+
+maintainers:
+ - Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxx>
+
+allOf:
+ - $ref: "spi-controller.yaml#"
+
+properties:
+ compatible:
+ oneOf:
+ - items:
You don't need 'oneOf' if there is only one entry...
So you've dropped 'cdns,qspi-nor' alone being valid. Granted, the txt
file was fuzzy as to whether or not that was valid. So you have to look
at all the dts files and see. I prefer we don't allow that and require a
more specific compatible, but if there's a bunch then we should allow
for it. The commit message should summarize what you decide.
we need bunch of compatibles as below, TI, Altera and Intel uses
different compatible's so we added 'oneOf'.
cdns,qspi-nor can be dropped instead I can add cadence,qspi ,because
this driver suuports qspi-nor and qspi-nand as well.
Sure, let me go through other documentation files for reference.
+ - enum:
+ - ti,k2g-qspi
+ - ti,am654-ospi
+ - const: cdns,qspi-nor
+examples:
+ - |
+ qspi: spi@ff705000 {
+ compatible = "cadence,qspi","cdns,qpsi-nor";
And you missed fixing this.
Yes, fixed by "cadence,qspi" keeping alone, need to remove
cdns,qspi-nor, thanks!
Regards
Vadivel
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xff705000 0x1000>,
+ <0xffa00000 0x1000>;
+ interrupts = <0 151 4>;
+ clocks = <&qspi_clk>;
+ cdns,fifo-depth = <128>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x00000000>;
+ resets = <&rst 0x1>, <&rst 0x2>;
+ reset-names = "qspi", "qspi-ocp";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ cdns,read-delay = <4>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+ };
+
+ };
+
+...
--
2.11.0
