On Fri, Oct 30, 2020 at 01:31:52PM +0800, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
>
> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
>
> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/spi/cadence-quadspi.txt | 67 ---------
> .../devicetree/bindings/spi/cadence-quadspi.yaml | 149 +++++++++++++++++++++
> 2 files changed, 149 insertions(+), 67 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> deleted file mode 100644
> index 945be7d5b236..000000000000
> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> +++ /dev/null
> @@ -1,67 +0,0 @@
> -* Cadence Quad SPI controller
> -
> -Required properties:
> -- compatible : should be one of the following:
> - Generic default - "cdns,qspi-nor".
> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
> -- reg : Contains two entries, each of which is a tuple consisting of a
> - physical address and length. The first entry is the address and
> - length of the controller register set. The second entry is the
> - address and length of the QSPI Controller data area.
> -- interrupts : Unit interrupt specifier for the controller interrupt.
> -- clocks : phandle to the Quad SPI clock.
> -- cdns,fifo-depth : Size of the data FIFO in words.
> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
> -
> -Optional properties:
> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
> - the read data rather than the QSPI clock. Make sure that QSPI return
> - clock is populated on the board before using this property.
> -
> -Optional subnodes:
> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
> -custom properties:
> -- cdns,read-delay : Delay for read capture logic, in clock cycles
> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
> - mode chip select outputs are de-asserted between
> - transactions.
> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
> - de-activated and the activation of another.
> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
> - transaction and deasserting the device chip select
> - (qspi_n_ss_out).
> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
> - and first bit transfer.
> -- resets : Must contain an entry for each entry in reset-names.
> - See ../reset/reset.txt for details.
> -- reset-names : Must include either "qspi" and/or "qspi-ocp".
> -
> -Example:
> -
> - qspi: spi@ff705000 {
> - compatible = "cdns,qspi-nor";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <0xff705000 0x1000>,
> - <0xffa00000 0x1000>;
> - interrupts = <0 151 4>;
> - clocks = <&qspi_clk>;
> - cdns,is-decoded-cs;
> - cdns,fifo-depth = <128>;
> - cdns,fifo-width = <4>;
> - cdns,trigger-address = <0x00000000>;
> - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> - reset-names = "qspi", "qspi-ocp";
> -
> - flash0: n25q00@0 {
> - ...
> - cdns,read-delay = <4>;
> - cdns,tshsl-ns = <50>;
> - cdns,tsd2d-ns = <50>;
> - cdns,tchsh-ns = <4>;
> - cdns,tslch-ns = <4>;
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> new file mode 100644
> index 000000000000..ec22b040d804
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> @@ -0,0 +1,149 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Cadence Quad SPI controller
> +
> +maintainers:
> + - Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxx>
> +
> +allOf:
> + - $ref: "spi-controller.yaml#"
> +
> +properties:
> + compatible:
> + oneOf:
> + - items:
You don't need 'oneOf' if there is only one entry...
So you've dropped 'cdns,qspi-nor' alone being valid. Granted, the txt
file was fuzzy as to whether or not that was valid. So you have to look
at all the dts files and see. I prefer we don't allow that and require a
more specific compatible, but if there's a bunch then we should allow
for it. The commit message should summarize what you decide.
> + - enum:
> + - ti,k2g-qspi
> + - ti,am654-ospi
> + - const: cdns,qspi-nor
> +examples:
> + - |
> + qspi: spi@ff705000 {
> + compatible = "cadence,qspi","cdns,qpsi-nor";
And you missed fixing this.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0xff705000 0x1000>,
> + <0xffa00000 0x1000>;
> + interrupts = <0 151 4>;
> + clocks = <&qspi_clk>;
> + cdns,fifo-depth = <128>;
> + cdns,fifo-width = <4>;
> + cdns,trigger-address = <0x00000000>;
> + resets = <&rst 0x1>, <&rst 0x2>;
> + reset-names = "qspi", "qspi-ocp";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + cdns,read-delay = <4>;
> + cdns,tshsl-ns = <50>;
> + cdns,tsd2d-ns = <50>;
> + cdns,tchsh-ns = <4>;
> + cdns,tslch-ns = <4>;
> + };
> +
> + };
> +
> +...
> --
> 2.11.0
>
