Hello, this series has been broken out from " [PATCH 0/8] dt-bindings: media: i2c: Convert to json-schema" which I sent out a few days ago. It was a single patch, now it's 13. Not sure it's a good sign :) Anyway, in the version sent as part of the mentioned series I just converted the existing bindings to the json-schema format, without putting to much attention to what was there. As suggested by Laurent I moved to specify properties as dt-schema, to allow their validation, and that sprinkled to a lot of fun. For each patch in the series, the DTS and bindings maintainers are CC-ed. The whole series has been sent to a limited audience only. The series starts with a plain conversion of the existing bindings to dt-schema. It then fixes a potential issue on a dts user of the sensor, and then move to remove or demote endpoint properties that were marked as required in the original text bindings. This of course causes a log of churn in the existing DTS which use the sensor, and opens some questions there from which I expect the individual maintainers to provide directions on. Finally, the small patch for the driver to initialize DVP default signal values to what the sensor manual and the bindings report. The series ends with the update of the MAINTAINERS file with the new .yaml binding file and the addition of myself as co-maintainer for the driver. Steve if you intended to remove yourself please send a patch, I didn't dare to do it myself :) A final note for Rob and his bot: some patches breaks validation of existing dts, which are then fixed by following patches. Hope this is ok, but it I have to keep validation of all dts successful, patches would likely be huge and hinder changes which I preferred to make explicitly in single patches. Jacopo Mondi (13): dt-bindings: media: ov5640: Convert to json-schema arm64: dts: qcom: apq8016-sbc: Fix CSI-2 lanes routing dt-bindings: media: ov5640: Do not limit rotation dt-bindings: media: ti,cal: Remove sensor from example dt-bindings: media: ov5640: Make bus-type mandatory dt-bindings: media: ov5640: Require ep properties dt-bindings: media: ov5640: Remove clock-lanes dt-bindings: media: ov5640: Remove data-shift dt-bindings: media: ov5640: Add default for synch signals dt-bindings: media: ov5640: Demote DVP required properties media: i2c: ov5640: Initialize DVP polarities as default MAINTAINERS: ov5640: Add bindings file dt-bindings: media: ov5640: Add myself as co-maintainer .../devicetree/bindings/media/i2c/ov5640.txt | 92 -------- .../devicetree/bindings/media/i2c/ov5640.yaml | 208 ++++++++++++++++++ .../devicetree/bindings/media/ti,cal.yaml | 22 -- MAINTAINERS | 2 + arch/arm/boot/dts/dra72-evm-common.dtsi | 2 +- arch/arm/boot/dts/dra76-evm.dts | 2 +- arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi | 2 +- arch/arm/boot/dts/imx6qdl-icore.dtsi | 2 +- arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 2 +- arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 2 +- arch/arm/boot/dts/stm32mp157c-ev1.dts | 2 +- .../allwinner/sun50i-a64-amarula-relic.dts | 1 + .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 1 + arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 8 +- .../arm64/boot/dts/ti/k3-am654-base-board.dts | 2 +- drivers/media/i2c/ov5640.c | 16 +- 16 files changed, 232 insertions(+), 134 deletions(-) delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.yaml -- 2.27.0
