Hi Laurent
Thanks for the review.
> -----Original Message-----
> From: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Sent: Wednesday, May 6, 2020 8:42 PM
> To: Vishal Sagar <vsagar@xxxxxxxxxx>
> Cc: Hyun Kwon <hyunk@xxxxxxxxxx>; mchehab@xxxxxxxxxx;
> robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx; Michal Simek
> <michals@xxxxxxxxxx>; linux-media@xxxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; hans.verkuil@xxxxxxxxx; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Dinesh Kumar
> <dineshk@xxxxxxxxxx>; Sandip Kothari <sandipk@xxxxxxxxxx>; Joe Perches
> <joe@xxxxxxxxxxx>
> Subject: Re: [PATCH v2 2/2] media: v4l: xilinx: Add Xilinx UHD-SDI Rx Subsystem
> driver
>
> Hi Vishal,
>
> Thank you for the patch.
>
> There are a few questions for Hans below.
>
> On Wed, Apr 29, 2020 at 07:47:04PM +0530, Vishal Sagar wrote:
> > The Xilinx UHD-SDI Rx subsystem soft IP is used to capture native SDI
> > streams from SDI sources like SDI broadcast equipment like cameras and
> > mixers. This block outputs either native SDI, native video or
> > AXI4-Stream compliant data stream for further processing. Please refer
> > to PG290 for details.
> >
> > The driver is used to configure the IP to add framer, search for
> > specific modes, get the detected mode, stream parameters, errors, etc.
> > It also generates events for video lock/unlock, bridge over/under flow.
> >
> > The driver supports 10/12 bpc YUV 422 media bus format currently. It also
> > decodes the stream parameters based on the ST352 packet embedded in the
> > stream. In case the ST352 packet isn't present in the stream, the core's
> > detected properties are used to set stream properties.
>
> As commented on patch 1/2, I don't see a mention of 12 bpc in the
> documentation. Let's discuss it as part of patch 1/2.
>
Ok.
> > The driver currently supports only the AXI4-Stream IP configuration.
> >
> > Signed-off-by: Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> > ---
> > v2
> > - Added DV timing support based on Hans Verkuilś feedback
> > - More documentation to custom v4l controls and events
> > - Fixed Hyunś comments
> > - Added macro for masking and shifting as per Joe Perches comments
> > - Updated to latest as per Xilinx github repo driver like
> > adding new DV timings not in mainline yet uptill 03/21/20
> >
> > drivers/media/platform/xilinx/Kconfig | 11 +
> > drivers/media/platform/xilinx/Makefile | 1 +
> > .../media/platform/xilinx/xilinx-sdirxss.c | 2162 +++++++++++++++++
> > include/uapi/linux/xilinx-sdirxss.h | 179 ++
> > include/uapi/linux/xilinx-v4l2-controls.h | 67 +
> > 5 files changed, 2420 insertions(+)
> > create mode 100644 drivers/media/platform/xilinx/xilinx-sdirxss.c
> > create mode 100644 include/uapi/linux/xilinx-sdirxss.h
> >
> > diff --git a/drivers/media/platform/xilinx/Kconfig
> b/drivers/media/platform/xilinx/Kconfig
> > index 01c96fb66414..77091318a9c9 100644
> > --- a/drivers/media/platform/xilinx/Kconfig
> > +++ b/drivers/media/platform/xilinx/Kconfig
> > @@ -12,6 +12,17 @@ config VIDEO_XILINX
> >
> > if VIDEO_XILINX
> >
> > +config VIDEO_XILINX_SDIRXSS
> > + tristate "Xilinx UHD SDI Rx Subsystem"
> > + help
> > + Driver for Xilinx UHD-SDI Rx Subsystem. This is a V4L sub-device
> > + based driver that takes input from a SDI source like SDI camera and
> > + converts it into an AXI4-Stream. The subsystem comprises of a SMPTE
>
> s/comprises of/comprises/
>
Ok I will fix this in v3.
> > + UHD-SDI Rx core, a SDI Rx to Native Video bridge and a Video In to
> > + AXI4-Stream bridge. The driver is used to set different stream
> > + detection modes and identify stream properties to properly configure
> > + downstream.
> > +
> > config VIDEO_XILINX_TPG
> > tristate "Xilinx Video Test Pattern Generator"
> > depends on VIDEO_XILINX
> > diff --git a/drivers/media/platform/xilinx/Makefile
> b/drivers/media/platform/xilinx/Makefile
> > index 4cdc0b1ec7a5..6c375f03f587 100644
> > --- a/drivers/media/platform/xilinx/Makefile
> > +++ b/drivers/media/platform/xilinx/Makefile
> > @@ -2,6 +2,7 @@
> >
> > xilinx-video-objs += xilinx-dma.o xilinx-vip.o xilinx-vipp.o
> >
> > +obj-$(CONFIG_VIDEO_XILINX_SDIRXSS) += xilinx-sdirxss.o
> > obj-$(CONFIG_VIDEO_XILINX) += xilinx-video.o
> > obj-$(CONFIG_VIDEO_XILINX_TPG) += xilinx-tpg.o
> > obj-$(CONFIG_VIDEO_XILINX_VTC) += xilinx-vtc.o
> > diff --git a/drivers/media/platform/xilinx/xilinx-sdirxss.c
> b/drivers/media/platform/xilinx/xilinx-sdirxss.c
> > new file mode 100644
> > index 000000000000..c536ea3aaa0d
> > --- /dev/null
> > +++ b/drivers/media/platform/xilinx/xilinx-sdirxss.c
> > @@ -0,0 +1,2162 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Driver for Xilinx SDI Rx Subsystem
> > + *
> > + * Copyright (C) 2017 - 2020 Xilinx, Inc.
> > + *
> > + * Contacts: Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> > + *
>
> You can remove this blank line.
>
Agree. I will remove this in v3.
> > + */
> > +
> > +#include <dt-bindings/media/xilinx-vip.h>
> > +#include <linux/bitops.h>
> > +#include <linux/compiler.h>
> > +#include <linux/clk.h>
>
> You nearly got the alphabetical order right ;-)
>
> > +#include <linux/delay.h>
>
> No use of delay or sleep functions in the code, is this needed ?
>
> > +#include <linux/device.h>
>
> You can probably drop this one as you include platform_device.h.
>
> > +#include <linux/interrupt.h>
> > +#include <linux/io.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_irq.h>
>
> I don't think of_irq is needed either.
>
> > +#include <linux/platform_device.h>
> > +#include <linux/pm.h>
> > +#include <linux/slab.h>
> > +#include <linux/spinlock.h>
> > +#include <linux/spinlock_types.h>
>
> The driver doesn't seems to use spinlocks, you can remove those two
> headers.
>
> > +#include <linux/types.h>
> > +#include <linux/v4l2-dv-timings.h>
> > +#include <linux/v4l2-subdev.h>
> > +#include <linux/xilinx-sdirxss.h>
> > +#include <linux/xilinx-v4l2-controls.h>
> > +#include <media/media-entity.h>
> > +#include <media/v4l2-common.h>
> > +#include <media/v4l2-ctrls.h>
> > +#include <media/v4l2-event.h>
> > +#include <media/v4l2-fwnode.h>
> > +#include <media/v4l2-subdev.h>
> > +#include "xilinx-vip.h"
> > +
I will fix the headers list by removing unnecessary includes
> > +/*
> > + * SDI Rx register map, bitmask and offsets
> > + */
> > +#define XSDIRX_RST_CTRL_REG 0x00
> > +#define XSDIRX_MDL_CTRL_REG 0x04
> > +#define XSDIRX_GLBL_IER_REG 0x0C
> > +#define XSDIRX_ISR_REG 0x10
> > +#define XSDIRX_IER_REG 0x14
> > +#define XSDIRX_ST352_VALID_REG 0x18
> > +#define XSDIRX_ST352_DS1_REG 0x1C
>
> Could you use lower-case hex values ? That's the most common option in
> kernel code. If you use vim,
>
> :%s/\<0x[0-9A-F]\+\>/\L\0/
>
> I'm sure there's an emacs equivalent :-)
>
[Vishal Sagar]
Sure I will change this. Thanks for sharing the regex to do that.
I use vim 😊
> > +#define XSDIRX_ST352_DS3_REG 0x20
> > +#define XSDIRX_ST352_DS5_REG 0x24
> > +#define XSDIRX_ST352_DS7_REG 0x28
> > +#define XSDIRX_ST352_DS9_REG 0x2C
> > +#define XSDIRX_ST352_DS11_REG 0x30
> > +#define XSDIRX_ST352_DS13_REG 0x34
> > +#define XSDIRX_ST352_DS15_REG 0x38
> > +#define XSDIRX_VERSION_REG 0x3C
> > +#define XSDIRX_SS_CONFIG_REG 0x40
> > +#define XSDIRX_MODE_DET_STAT_REG 0x44
> > +#define XSDIRX_TS_DET_STAT_REG 0x48
> > +#define XSDIRX_EDH_STAT_REG 0x4C
> > +#define XSDIRX_EDH_ERRCNT_EN_REG 0x50
> > +#define XSDIRX_EDH_ERRCNT_REG 0x54
> > +#define XSDIRX_CRC_ERRCNT_REG 0x58
> > +#define XSDIRX_VID_LOCK_WINDOW_REG 0x5C
> > +#define XSDIRX_SB_RX_STS_REG 0x60
> > +
> > +#define XSDIRX_RST_CTRL_SS_EN_MASK BIT(0)
> > +#define XSDIRX_RST_CTRL_SRST_MASK BIT(1)
> > +#define XSDIRX_RST_CTRL_RST_CRC_ERRCNT_MASK BIT(2)
> > +#define XSDIRX_RST_CTRL_RST_EDH_ERRCNT_MASK BIT(3)
> > +#define XSDIRX_RST_CTRL_SDIRX_BRIDGE_ENB_MASK BIT(8)
> > +#define XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK BIT(9)
> > +#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_OFFSET 10
> > +#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_MASK GENMASK(12,
> 10)
> > +#define XSDIRX_RST_CTRL_BRIDGE_CH_FMT_YUV444 1
> > +
> > +#define XSDIRX_MDL_CTRL_FRM_EN_MASK BIT(4)
> > +#define XSDIRX_MDL_CTRL_MODE_DET_EN_MASK BIT(5)
> > +#define XSDIRX_MDL_CTRL_MODE_HD_EN_MASK BIT(8)
> > +#define XSDIRX_MDL_CTRL_MODE_SD_EN_MASK BIT(9)
> > +#define XSDIRX_MDL_CTRL_MODE_3G_EN_MASK BIT(10)
> > +#define XSDIRX_MDL_CTRL_MODE_6G_EN_MASK BIT(11)
> > +#define XSDIRX_MDL_CTRL_MODE_12GI_EN_MASK BIT(12)
> > +#define XSDIRX_MDL_CTRL_MODE_12GF_EN_MASK BIT(13)
> > +#define XSDIRX_MDL_CTRL_MODE_AUTO_DET_MASK GENMASK(13,
> 8)
> > +
> > +#define XSDIRX_MDL_CTRL_FORCED_MODE_OFFSET 16
> > +#define XSDIRX_MDL_CTRL_FORCED_MODE_MASK GENMASK(18, 16)
> > +
> > +#define XSDIRX_GLBL_INTR_EN_MASK BIT(0)
> > +
> > +#define XSDIRX_INTR_VIDLOCK_MASK BIT(0)
> > +#define XSDIRX_INTR_VIDUNLOCK_MASK BIT(1)
> > +#define XSDIRX_INTR_OVERFLOW_MASK BIT(9)
> > +#define XSDIRX_INTR_UNDERFLOW_MASK BIT(10)
> > +
> > +#define XSDIRX_INTR_ALL_MASK (XSDIRX_INTR_VIDLOCK_MASK |\
> > + XSDIRX_INTR_VIDUNLOCK_MASK |\
> > + XSDIRX_INTR_OVERFLOW_MASK |\
> > + XSDIRX_INTR_UNDERFLOW_MASK)
> > +
> > +#define XSDIRX_ST352_VALID_DS1_MASK BIT(0)
> > +#define XSDIRX_ST352_VALID_DS3_MASK BIT(1)
> > +#define XSDIRX_ST352_VALID_DS5_MASK BIT(2)
> > +#define XSDIRX_ST352_VALID_DS7_MASK BIT(3)
> > +#define XSDIRX_ST352_VALID_DS9_MASK BIT(4)
> > +#define XSDIRX_ST352_VALID_DS11_MASK BIT(5)
> > +#define XSDIRX_ST352_VALID_DS13_MASK BIT(6)
> > +#define XSDIRX_ST352_VALID_DS15_MASK BIT(7)
> > +
> > +#define XSDIRX_MODE_DET_STAT_RX_MODE_MASK GENMASK(2, 0)
> > +#define XSDIRX_MODE_DET_STAT_MODE_LOCK_MASK BIT(3)
> > +#define XSDIRX_MODE_DET_STAT_ACT_STREAM_MASK GENMASK(6,
> 4)
> > +#define XSDIRX_MODE_DET_STAT_ACT_STREAM_OFFSET 4
> > +#define XSDIRX_MODE_DET_STAT_LVLB_3G_MASK BIT(7)
> > +
> > +#define XSDIRX_TS_DET_STAT_LOCKED_MASK BIT(0)
> > +#define XSDIRX_TS_DET_STAT_SCAN_MASK BIT(1)
> > +#define XSDIRX_TS_DET_STAT_SCAN_OFFSET (1)
> > +#define XSDIRX_TS_DET_STAT_FAMILY_MASK GENMASK(7,
> 4)
> > +#define XSDIRX_TS_DET_STAT_FAMILY_OFFSET (4)
> > +#define XSDIRX_TS_DET_STAT_RATE_MASK GENMASK(11, 8)
> > +#define XSDIRX_TS_DET_STAT_RATE_OFFSET (8)
> > +
> > +#define XSDIRX_TS_DET_STAT_RATE_NONE 0x0
> > +#define XSDIRX_TS_DET_STAT_RATE_23_98HZ 0x2
> > +#define XSDIRX_TS_DET_STAT_RATE_24HZ 0x3
> > +#define XSDIRX_TS_DET_STAT_RATE_47_95HZ 0x4
> > +#define XSDIRX_TS_DET_STAT_RATE_25HZ 0x5
> > +#define XSDIRX_TS_DET_STAT_RATE_29_97HZ 0x6
> > +#define XSDIRX_TS_DET_STAT_RATE_30HZ 0x7
> > +#define XSDIRX_TS_DET_STAT_RATE_48HZ 0x8
> > +#define XSDIRX_TS_DET_STAT_RATE_50HZ 0x9
> > +#define XSDIRX_TS_DET_STAT_RATE_59_94HZ 0xA
> > +#define XSDIRX_TS_DET_STAT_RATE_60HZ 0xB
> > +
> > +#define XSDIRX_EDH_STAT_EDH_AP_MASK BIT(0)
> > +#define XSDIRX_EDH_STAT_EDH_FF_MASK BIT(1)
> > +#define XSDIRX_EDH_STAT_EDH_ANC_MASK BIT(2)
> > +#define XSDIRX_EDH_STAT_AP_FLAG_MASK GENMASK(8, 4)
> > +#define XSDIRX_EDH_STAT_FF_FLAG_MASK GENMASK(13, 9)
> > +#define XSDIRX_EDH_STAT_ANC_FLAG_MASK GENMASK(18, 14)
> > +#define XSDIRX_EDH_STAT_PKT_FLAG_MASK GENMASK(22, 19)
> > +
> > +#define XSDIRX_EDH_ERRCNT_COUNT_MASK GENMASK(15, 0)
> > +
> > +#define XSDIRX_CRC_ERRCNT_COUNT_MASK GENMASK(31, 16)
> > +#define XSDIRX_CRC_ERRCNT_DS_CRC_MASK GENMASK(15, 0)
> > +
> > +#define XSDIRX_VERSION_REV_MASK GENMASK(7, 0)
> > +#define XSDIRX_VERSION_PATCHID_MASK GENMASK(11, 8)
> > +#define XSDIRX_VERSION_VER_REV_MASK GENMASK(15, 12)
> > +#define XSDIRX_VERSION_VER_MIN_MASK GENMASK(23, 16)
> > +#define XSDIRX_VERSION_VER_MAJ_MASK GENMASK(31, 24)
> > +
> > +#define XSDIRX_SS_CONFIG_EDH_INCLUDED_MASK BIT(1)
> > +
> > +#define XSDIRX_STAT_SB_RX_TDATA_CHANGE_DONE_MASK BIT(0)
> > +#define XSDIRX_STAT_SB_RX_TDATA_CHANGE_FAIL_MASK BIT(1)
> > +#define XSDIRX_STAT_SB_RX_TDATA_GT_RESETDONE_MASK BIT(2)
> > +#define XSDIRX_STAT_SB_RX_TDATA_GT_BITRATE_MASK BIT(3)
> > +
> > +#define XSDIRX_DEFAULT_WIDTH (1920)
>
> No need for parentheses around integer values in macros.
>
I will remove these in next version.
> > +#define XSDIRX_DEFAULT_HEIGHT (1080)
> > +
> > +#define XSDIRX_MAX_STR_LENGTH 16
> > +
> > +#define XSDIRXSS_SDI_STD_3G 0
> > +#define XSDIRXSS_SDI_STD_6G 1
> > +#define XSDIRXSS_SDI_STD_12G_8DS 2
>
> Should these three constants be placed in an enum ? The
> xsdirxss_core.mode field would then become an enum.
>
I will get core->mode directly from dt-bindings. So enum type won't be necessary.
> > +
> > +#define XSDIRX_DEFAULT_VIDEO_LOCK_WINDOW 0x3000
> > +
> > +#define XSDIRX_MODE_HD_MASK 0x0
> > +#define XSDIRX_MODE_SD_MASK 0x1
> > +#define XSDIRX_MODE_3G_MASK 0x2
> > +#define XSDIRX_MODE_6G_MASK 0x4
> > +#define XSDIRX_MODE_12GI_MASK 0x5
> > +#define XSDIRX_MODE_12GF_MASK 0x6
> > +
> > +/* Maximum number of events per file handle. */
> > +#define XSDIRX_MAX_EVENTS (128)
>
> Do we really need such a high number ? How often are the overflow and
> underflow expected ?
>
An overflow or underflow events will occur when a resolution / rate change occurs.
But since we are stopping the bridges in irq handler, these events will stop coming.
I can reduce this to 8 events but it is arbitrary. Is that ok?
> > +
> > +/* ST352 related macros */
> > +#define XST352_PAYLOAD_BYTE1_MASK 0xFF
> > +#define XST352_PAYLOAD_BYTE1_OFFSET 0
> > +#define XST352_PAYLOAD_BYTE2_OFFSET 8
> > +#define XST352_PAYLOAD_BYTE3_OFFSET 16
> > +#define XST352_PAYLOAD_BYTE4_OFFSET 24
> > +
> > +#define XST352_BYTE1_ST292_1x720L_1_5G 0x84
> > +#define XST352_BYTE1_ST292_1x1080L_1_5G 0x85
> > +#define XST352_BYTE1_ST425_2008_750L_3GB 0x88
> > +#define XST352_BYTE1_ST425_2008_1125L_3GA 0x89
> > +#define XST352_BYTE1_ST372_DL_3GB 0x8A
> > +#define XST352_BYTE1_ST372_2x720L_3GB 0x8B
> > +#define XST352_BYTE1_ST372_2x1080L_3GB 0x8C
> > +#define XST352_BYTE1_ST2081_10_2160L_6G 0xC0
> > +#define XST352_BYTE1_ST2081_10_2_1080L_6G 0xC1
> > +#define XST352_BYTE1_ST2081_10_DL_2160L_6G 0xC2
> > +#define XST352_BYTE1_ST2082_10_2160L_12G 0xCE
> > +
> > +#define XST352_BYTE2_TS_TYPE_MASK BIT(15)
> > +#define XST352_BYTE2_TS_TYPE_OFFSET 15
> > +#define XST352_BYTE2_PIC_TYPE_MASK BIT(14)
> > +#define XST352_BYTE2_PIC_TYPE_OFFSET 14
> > +#define XST352_BYTE2_TS_PIC_TYPE_INTERLACED 0
> > +#define XST352_BYTE2_TS_PIC_TYPE_PROGRESSIVE 1
> > +
> > +#define XST352_BYTE2_FPS_MASK 0xF
> > +#define XST352_BYTE2_FPS_OFFSET 8
> > +#define XST352_BYTE2_FPS_24F 0x2
> > +#define XST352_BYTE2_FPS_24 0x3
> > +#define XST352_BYTE2_FPS_48F 0x4
> > +#define XST352_BYTE2_FPS_25 0x5
> > +#define XST352_BYTE2_FPS_30F 0x6
> > +#define XST352_BYTE2_FPS_30 0x7
> > +#define XST352_BYTE2_FPS_48 0x8
> > +#define XST352_BYTE2_FPS_50 0x9
> > +#define XST352_BYTE2_FPS_60F 0xA
> > +#define XST352_BYTE2_FPS_60 0xB
> > +/* Table 4 ST 2081-10:2015 */
> > +#define XST352_BYTE2_FPS_96 0xC
> > +#define XST352_BYTE2_FPS_100 0xD
> > +#define XST352_BYTE2_FPS_120 0xE
> > +#define XST352_BYTE2_FPS_120F 0xF
> > +
> > +#define XST352_BYTE3_ACT_LUMA_COUNT_MASK BIT(22)
> > +#define XST352_BYTE3_ACT_LUMA_COUNT_OFFSET 22
> > +
> > +#define XST352_BYTE3_COLOR_FORMAT_MASK GENMASK(19,
> 16)
> > +#define XST352_BYTE3_COLOR_FORMAT_OFFSET 16
> > +#define XST352_BYTE3_COLOR_FORMAT_422 0x0
> > +#define XST352_BYTE3_COLOR_FORMAT_YUV444 0x1
> > +#define XST352_BYTE3_COLOR_FORMAT_420 0x3
> > +#define XST352_BYTE3_COLOR_FORMAT_GBR 0x2
> > +
> > +#define XST352_BYTE4_BIT_DEPTH_MASK GENMASK(25, 24)
> > +#define XST352_BYTE4_BIT_DEPTH_OFFSET 24
> > +#define XST352_BYTE4_BIT_DEPTH_10 0x1
> > +#define XST352_BYTE4_BIT_DEPTH_12 0x2
> > +
> > +#define CLK_INT 148500000UL
> > +
> > +#define rshift_and_mask(val, type) \
> > + (((val) >> type##_OFFSET) & type##_MASK)
> > +
> > +#define mask_and_rshift(val, type) \
> > + (((val) & type##_MASK) >> type##_OFFSET)
>
> How about using FIELD_GET() from linux/bitfield.h ? It's more standard,
> and will thus be less confusing to readers.
>
Ok I will try to convert this to FIELD_GET()
> > +
> > +/**
> > + * enum sdi_family_enc - SDI Transport Video Format Detected with Active
> Pixels
> > + * @XSDIRX_SMPTE_ST_274: SMPTE ST 274 detected with AP 1920x1080
> > + * @XSDIRX_SMPTE_ST_296: SMPTE ST 296 detected with AP 1280x720
> > + * @XSDIRX_SMPTE_ST_2048_2: SMPTE ST 2048-2 detected with AP
> 2048x1080
> > + * @XSDIRX_SMPTE_ST_295: SMPTE ST 295 detected with AP 1920x1080
> > + * @XSDIRX_NTSC: NTSC encoding detected with AP 720x486
> > + * @XSDIRX_PAL: PAL encoding detected with AP 720x576
> > + * @XSDIRX_TS_UNKNOWN: Unknown SMPTE Transport family type
> > + */
> > +enum sdi_family_enc {
> > + XSDIRX_SMPTE_ST_274 = 0,
> > + XSDIRX_SMPTE_ST_296 = 1,
> > + XSDIRX_SMPTE_ST_2048_2 = 2,
> > + XSDIRX_SMPTE_ST_295 = 3,
> > + XSDIRX_NTSC = 8,
> > + XSDIRX_PAL = 9,
> > + XSDIRX_TS_UNKNOWN = 15
> > +};
>
> This should ideally go in a header file shared between the SDI RX and
> TX, as it's part of the UHD-SDI IP core, but it can be done later.
>
Right. We can look into this later.
> > +
> > +/**
> > + * struct xsdirxss_core - Core configuration SDI Rx Subsystem device
> structure
> > + * @dev: Platform structure
> > + * @iomem: Base address of subsystem
> > + * @irq: requested irq number
> > + * @include_edh: EDH processor presence
> > + * @mode: 3G/6G/12G mode
> > + * @clks: array of clocks
> > + * @num_clks: number of clocks
> > + * @bpc: Bits per component, can be 10 or 12
> > + */
> > +struct xsdirxss_core {
> > + struct device *dev;
> > + void __iomem *iomem;
> > + int irq;
> > + bool include_edh;
> > + int mode;
> > + struct clk_bulk_data *clks;
> > + int num_clks;
>
> num_clks is never negative, you can make it an unsigned int.
Ok. I will make num_clks as unsigned int.
So why devm_clk_bulk_get() and clk_bulk_prepare_enable() take in num_clks argument as int ?
>
> > + u32 bpc;
> > +};
> > +
> > +/**
> > + * struct xsdirxss_state - SDI Rx Subsystem device structure
> > + * @core: Core structure for MIPI SDI Rx Subsystem
> > + * @subdev: The v4l2 subdev structure
> > + * @ctrl_handler: control handler
> > + * @event: Holds the video unlock event
> > + * @format: Active V4L2 format on source pad
> > + * @default_format: default V4L2 media bus format
> > + * @frame_interval: Captures the frame rate
> > + * @pad: source media pad
> > + * @vidlockwin: Video lock window value set by control
> > + * @edhmask: EDH mask set by control
> > + * @searchmask: Search mask set by control
> > + * @streaming: Flag for storing streaming state
> > + * @vidlocked: Flag indicating SDI Rx has locked onto video stream
> > + * @ts_is_interlaced: Flag indicating Transport Stream is interlaced.
> > + * @framer_enable: Flag for framer enabled or not set by control
> > + *
> > + * This structure contains the device driver related parameters
> > + */
> > +struct xsdirxss_state {
> > + struct xsdirxss_core core;
> > + struct v4l2_subdev subdev;
> > + struct v4l2_ctrl_handler ctrl_handler;
> > + struct v4l2_event event;
>
> Is this needed, can't it be a local variable in the function where it is
> used ?
Yes this will be removed in next version and made a local variable in the irq handler.
>
> > + struct v4l2_mbus_framefmt format;
> > + struct v4l2_mbus_framefmt default_format;
> > + struct v4l2_fract frame_interval;
> > + struct media_pad pad;
>
> You will need two pads as there should be two ports (let's discuss it as
> part of patch 1/2).
>
Ok
> > + u32 vidlockwin;
> > + u32 edhmask;
> > + u16 searchmask;
> > + bool streaming;
> > + bool vidlocked;
> > + bool ts_is_interlaced;
> > + bool framer_enable;
> > +};
>
> As for the CSI2-RX, splitting core and state in separate structures
> isn't an established practice. I think it leads to more complex code as
> you have to remember in which structure each field is located.
>
I will merge the core and state into a single structure similar to CSI2-Rx case.
> > +
> > +/* List of clocks required by UHD-SDI Rx subsystem */
> > +static const char * const xsdirxss_clks[] = {
> > + "s_axi_aclk", "sdi_rx_clk", "video_out_clk",
> > +};
> > +
> > +/* TODO - Add YUV 444/420 and RBG 10/12 bpc mbus formats here */
>
> s/RBG/RGB/ ?
>
No RBG is correct because as per Xilinx User Guide 934 Figure 1-4 and Table 1-4,
the Blue is middle component in the AXI4-Stream protocol followed by all Xilinx Video IPs.
https://www.xilinx.com/support/documentation/ip_documentation/axi_videoip/v1_0/ug934_axi_videoIP.pdf
We will add the RBG 10 and 12 bpc formats later.
> > +static const u32 xsdirxss_10bpc_mbus_fmts[] = {
> > + MEDIA_BUS_FMT_UYVY10_1X20,
> > +};
> > +
> > +static const u32 xsdirxss_12bpc_mbus_fmts[] = {
> > + MEDIA_BUS_FMT_UYVY12_1X24,
> > +};
> > +
> > +static const struct v4l2_dv_timings fmt_cap[] = {
> > + V4L2_DV_BT_SDI_720X487I60,
> > + V4L2_DV_BT_CEA_720X576I50,
> > + V4L2_DV_BT_CEA_1280X720P24,
> > + V4L2_DV_BT_CEA_1280X720P25,
> > + V4L2_DV_BT_CEA_1280X720P30,
> > + V4L2_DV_BT_CEA_1280X720P50,
> > + V4L2_DV_BT_CEA_1280X720P60,
> > + V4L2_DV_BT_CEA_1920X1080P24,
> > + V4L2_DV_BT_CEA_1920X1080P30,
> > + V4L2_DV_BT_CEA_1920X1080I50,
> > + V4L2_DV_BT_CEA_1920X1080I60,
> > + V4L2_DV_BT_CEA_1920X1080P50,
> > + V4L2_DV_BT_CEA_1920X1080P60,
> > + V4L2_DV_BT_CEA_3840X2160P24,
> > + V4L2_DV_BT_CEA_3840X2160P30,
> > + V4L2_DV_BT_CEA_3840X2160P50,
> > + V4L2_DV_BT_CEA_3840X2160P60,
> > + V4L2_DV_BT_CEA_4096X2160P24,
> > + V4L2_DV_BT_CEA_4096X2160P25,
> > + V4L2_DV_BT_CEA_4096X2160P30,
> > + V4L2_DV_BT_CEA_4096X2160P50,
> > + V4L2_DV_BT_CEA_4096X2160P60,
> > +
> > + XLNX_V4L2_DV_BT_2048X1080P24,
> > + XLNX_V4L2_DV_BT_2048X1080P25,
> > + XLNX_V4L2_DV_BT_2048X1080P30,
> > + XLNX_V4L2_DV_BT_2048X1080I48,
> > + XLNX_V4L2_DV_BT_2048X1080I50,
> > + XLNX_V4L2_DV_BT_2048X1080I60,
> > + XLNX_V4L2_DV_BT_2048X1080P48,
> > + XLNX_V4L2_DV_BT_2048X1080P50,
> > + XLNX_V4L2_DV_BT_2048X1080P60,
> > + XLNX_V4L2_DV_BT_1920X1080P48,
> > + XLNX_V4L2_DV_BT_1920X1080I48,
> > + XLNX_V4L2_DV_BT_3840X2160P48,
> > + XLNX_V4L2_DV_BT_4096X2160P48,
> > +};
> > +
> > +struct xsdirxss_dv_map {
> > + u32 width;
> > + u32 height;
> > + u32 fps;
> > + struct v4l2_dv_timings format;
> > +};
> > +
> > +static const struct xsdirxss_dv_map xsdirxss_dv_timings[] = {
> > + /* SD - 720x487i60 */
> > + { 720, 243, 30, V4L2_DV_BT_SDI_720X487I60 },
> > + /* SD - 720x576i50 */
> > + { 720, 288, 25, V4L2_DV_BT_CEA_720X576I50 },
> > + /* HD - 1280x720p23.98 */
> > + /* HD - 1280x720p24 */
> > + { 1280, 720, 24, V4L2_DV_BT_CEA_1280X720P24 },
> > + /* HD - 1280x720p25 */
> > + { 1280, 720, 25, V4L2_DV_BT_CEA_1280X720P25 },
> > + /* HD - 1280x720p29.97 */
> > + /* HD - 1280x720p30 */
> > + { 1280, 720, 30, V4L2_DV_BT_CEA_1280X720P30 },
> > + /* HD - 1280x720p50 */
> > + { 1280, 720, 50, V4L2_DV_BT_CEA_1280X720P50 },
> > + /* HD - 1280x720p59.94 */
> > + /* HD - 1280x720p60 */
> > + { 1280, 720, 60, V4L2_DV_BT_CEA_1280X720P60 },
> > + /* HD - 1920x1080p23.98 */
> > + /* HD - 1920x1080p24 */
> > + { 1920, 1080, 24, V4L2_DV_BT_CEA_1920X1080P24 },
> > + /* HD - 1920x1080p25 */
> > + { 1920, 1080, 25, V4L2_DV_BT_CEA_1920X1080P25 },
> > + /* HD - 1920x1080p29.97 */
> > + /* HD - 1920x1080p30 */
> > + { 1920, 1080, 30, V4L2_DV_BT_CEA_1920X1080P30 },
> > +
> > + /* HD - 2048x1080p23.98 */
> > + /* HD - 2048x1080p24 */
> > + { 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P24 },
> > + /* HD - 2048x1080p25 */
> > + { 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P25 },
> > + /* HD - 2048x1080p29.97 */
> > + /* HD - 2048x1080p30 */
> > + { 2048, 1080, 24, XLNX_V4L2_DV_BT_2048X1080P30 },
> > + /* HD - 1920x1080i47.95 */
> > + /* HD - 1920x1080i48 */
> > + { 1920, 540, 24, XLNX_V4L2_DV_BT_1920X1080I48 },
> > +
> > + /* HD - 1920x1080i50 */
> > + { 1920, 540, 25, V4L2_DV_BT_CEA_1920X1080I50 },
> > + /* HD - 1920x1080i59.94 */
> > + /* HD - 1920x1080i60 */
> > + { 1920, 540, 30, V4L2_DV_BT_CEA_1920X1080I60 },
> > +
> > + /* HD - 2048x1080i47.95 */
> > + /* HD - 2048x1080i48 */
> > + { 2048, 540, 24, XLNX_V4L2_DV_BT_2048X1080I48 },
> > + /* HD - 2048x1080i50 */
> > + { 2048, 540, 25, XLNX_V4L2_DV_BT_2048X1080I50 },
> > + /* HD - 2048x1080i59.94 */
> > + /* HD - 2048x1080i60 */
> > + { 2048, 540, 30, XLNX_V4L2_DV_BT_2048X1080I60 },
> > + /* 3G - 1920x1080p47.95 */
> > + /* 3G - 1920x1080p48 */
> > + { 1920, 1080, 48, XLNX_V4L2_DV_BT_1920X1080P48 },
> > +
> > + /* 3G - 1920x1080p50 148.5 */
> > + { 1920, 1080, 50, V4L2_DV_BT_CEA_1920X1080P50 },
> > + /* 3G - 1920x1080p59.94 148.5/1.001 */
> > + /* 3G - 1920x1080p60 148.5 */
> > + { 1920, 1080, 60, V4L2_DV_BT_CEA_1920X1080P60 },
> > +
> > + /* 3G - 2048x1080p47.95 */
> > + /* 3G - 2048x1080p48 */
> > + { 2048, 1080, 48, XLNX_V4L2_DV_BT_2048X1080P48 },
> > + /* 3G - 2048x1080p50 */
> > + { 2048, 1080, 50, XLNX_V4L2_DV_BT_2048X1080P50 },
> > + /* 3G - 2048x1080p59.94 */
> > + /* 3G - 2048x1080p60 */
> > + { 2048, 1080, 60, XLNX_V4L2_DV_BT_2048X1080P60 },
> > +
> > + /* 6G - 3840X2160p23.98 */
> > + /* 6G - 3840X2160p24 */
> > + { 3840, 2160, 24, V4L2_DV_BT_CEA_3840X2160P24 },
> > + /* 6G - 3840X2160p25 */
> > + { 3840, 2160, 25, V4L2_DV_BT_CEA_3840X2160P25 },
> > + /* 6G - 3840X2160p29.97 */
> > + /* 6G - 3840X2160p30 */
> > + { 3840, 2160, 30, V4L2_DV_BT_CEA_3840X2160P30 },
> > + /* 6G - 4096X2160p23.98 */
> > + /* 6G - 4096X2160p24 */
> > + { 4096, 2160, 24, V4L2_DV_BT_CEA_4096X2160P24 },
> > + /* 6G - 4096X2160p25 */
> > + { 4096, 2160, 25, V4L2_DV_BT_CEA_4096X2160P25 },
> > + /* 6G - 4096X2160p29.97 */
> > + /* 6G - 4096X2160p30 */
> > + { 4096, 2160, 30, V4L2_DV_BT_CEA_4096X2160P30 },
> > + /* 12G - 3840X2160p47.95 */
> > + /* 12G - 3840X2160p48 */
> > + { 3840, 2160, 48, XLNX_V4L2_DV_BT_3840X2160P48 },
> > +
> > + /* 12G - 3840X2160p50 */
> > + { 3840, 2160, 50, V4L2_DV_BT_CEA_3840X2160P50 },
> > + /* 12G - 3840X2160p59.94 */
> > + /* 12G - 3840X2160p60 */
> > + { 3840, 2160, 60, V4L2_DV_BT_CEA_3840X2160P60 },
> > +
> > + /* 12G - 4096X2160p47.95 */
> > + /* 12G - 4096X2160p48 */
> > + { 3840, 2160, 48, XLNX_V4L2_DV_BT_4096X2160P48 },
> > +
> > + /* 12G - 4096X2160p50 */
> > + { 4096, 2160, 50, V4L2_DV_BT_CEA_4096X2160P50 },
> > + /* 12G - 4096X2160p59.94 */
> > + /* 12G - 4096X2160p60 */
> > + { 4096, 2160, 60, V4L2_DV_BT_CEA_4096X2160P60 },
> > +};
> > +
> > +static inline struct xsdirxss_state *
> > +to_xsdirxssstate(struct v4l2_subdev *subdev)
> > +{
> > + return container_of(subdev, struct xsdirxss_state, subdev);
> > +}
> > +
> > +/*
> > + * Register related operations
> > + */
> > +static inline u32 xsdirxss_read(struct xsdirxss_core *xsdirxss, u32 addr)
> > +{
> > + return ioread32(xsdirxss->iomem + addr);
> > +}
> > +
> > +static inline void xsdirxss_write(struct xsdirxss_core *xsdirxss, u32 addr,
> > + u32 value)
> > +{
> > + iowrite32(value, xsdirxss->iomem + addr);
> > +}
> > +
> > +static inline void xsdirxss_clr(struct xsdirxss_core *xsdirxss, u32 addr,
> > + u32 clr)
> > +{
> > + xsdirxss_write(xsdirxss, addr, xsdirxss_read(xsdirxss, addr) & ~clr);
> > +}
> > +
> > +static inline void xsdirxss_set(struct xsdirxss_core *xsdirxss, u32 addr,
> > + u32 set)
> > +{
> > + xsdirxss_write(xsdirxss, addr, xsdirxss_read(xsdirxss, addr) | set);
> > +}
> > +
> > +static inline void xsdirx_core_disable(struct xsdirxss_core *core)
> > +{
> > + xsdirxss_clr(core, XSDIRX_RST_CTRL_REG,
> XSDIRX_RST_CTRL_SS_EN_MASK);
> > +}
> > +
> > +static inline void xsdirx_core_enable(struct xsdirxss_core *core)
> > +{
> > + xsdirxss_set(core, XSDIRX_RST_CTRL_REG,
> XSDIRX_RST_CTRL_SS_EN_MASK);
> > +}
> > +
> > +static int xsdirx_set_modedetect(struct xsdirxss_core *core, u16 mask)
> > +{
> > + u32 val;
> > + struct device *dev = core->dev;
> > +
> > + mask &= XSDIRX_DETECT_ALL_MODES;
> > + if (!mask) {
> > + dev_err(dev, "Invalid bit mask = 0x%08x\n", mask);
> > + return -EINVAL;
> > + }
> > +
> > + dev_dbg(dev, "mask = 0x%x\n", mask);
> > +
> > + val = xsdirxss_read(core, XSDIRX_MDL_CTRL_REG);
> > + val &= ~XSDIRX_MDL_CTRL_MODE_DET_EN_MASK;
> > + val &= ~XSDIRX_MDL_CTRL_MODE_AUTO_DET_MASK;
> > + val &= ~XSDIRX_MDL_CTRL_FORCED_MODE_MASK;
> > +
> > + if (hweight16(mask) > 1) {
> > + /* Multi mode detection as more than 1 bit set in mask */
> > + dev_dbg(dev, "Detect multiple modes\n");
> > +
> > + if (mask & BIT(XSDIRX_MODE_SD_OFFSET))
> > + val |= XSDIRX_MDL_CTRL_MODE_SD_EN_MASK;
> > + if (mask & BIT(XSDIRX_MODE_HD_OFFSET))
> > + val |= XSDIRX_MDL_CTRL_MODE_HD_EN_MASK;
> > + if (mask & BIT(XSDIRX_MODE_3G_OFFSET))
> > + val |= XSDIRX_MDL_CTRL_MODE_3G_EN_MASK;
> > + if (mask & BIT(XSDIRX_MODE_6G_OFFSET))
> > + val |= XSDIRX_MDL_CTRL_MODE_6G_EN_MASK;
> > + if (mask & BIT(XSDIRX_MODE_12GI_OFFSET))
> > + val |= XSDIRX_MDL_CTRL_MODE_12GI_EN_MASK;
> > + if (mask & BIT(XSDIRX_MODE_12GF_OFFSET))
> > + val |= XSDIRX_MDL_CTRL_MODE_12GF_EN_MASK;
> > +
> > + val |= XSDIRX_MDL_CTRL_MODE_DET_EN_MASK;
> > + } else {
> > + /* Fixed Mode */
> > + u32 forced_mode_mask;
> > +
> > + dev_dbg(dev, "Detect fixed mode\n");
> > +
> > + /* Find offset of first bit set */
> > + switch (__ffs(mask)) {
> > + case XSDIRX_MODE_SD_OFFSET:
> > + forced_mode_mask = XSDIRX_MODE_SD_MASK;
> > + break;
> > + case XSDIRX_MODE_HD_OFFSET:
> > + forced_mode_mask = XSDIRX_MODE_HD_MASK;
> > + break;
> > + case XSDIRX_MODE_3G_OFFSET:
> > + forced_mode_mask = XSDIRX_MODE_3G_MASK;
> > + break;
> > + case XSDIRX_MODE_6G_OFFSET:
> > + forced_mode_mask = XSDIRX_MODE_6G_MASK;
> > + break;
> > + case XSDIRX_MODE_12GI_OFFSET:
> > + forced_mode_mask = XSDIRX_MODE_12GI_MASK;
> > + break;
> > + case XSDIRX_MODE_12GF_OFFSET:
> > + forced_mode_mask = XSDIRX_MODE_12GF_MASK;
> > + break;
> > + default:
> > + forced_mode_mask = 0;
> > + }
> > + dev_dbg(dev, "Forced Mode Mask : 0x%x\n",
> > + forced_mode_mask);
> > + val |= forced_mode_mask <<
> XSDIRX_MDL_CTRL_FORCED_MODE_OFFSET;
> > + }
> > +
> > + dev_dbg(dev, "Modes to be detected : sdi ctrl reg = 0x%08x\n",
> > + val);
> > + xsdirxss_write(core, XSDIRX_MDL_CTRL_REG, val);
> > +
> > + return 0;
> > +}
> > +
> > +static void xsdirx_framer(struct xsdirxss_core *core, bool flag)
> > +{
> > + if (flag)
> > + xsdirxss_set(core, XSDIRX_MDL_CTRL_REG,
> > + XSDIRX_MDL_CTRL_FRM_EN_MASK);
> > + else
> > + xsdirxss_clr(core, XSDIRX_MDL_CTRL_REG,
> > + XSDIRX_MDL_CTRL_FRM_EN_MASK);
> > +}
> > +
> > +static void xsdirx_setedherrcnttrigger(struct xsdirxss_core *core, u32
> enable)
>
> That's a hard to read function name. Could you separate words with
> underscores ? Same for functions below that concatenate multiple words
> together.
>
Ok. I will change the naming for this function and others below in next version.
> > +{
> > + u32 val = xsdirxss_read(core, XSDIRX_EDH_ERRCNT_EN_REG);
> > +
> > + val = enable & XSDIRX_EDH_ALLERR_MASK;
> > +
> > + xsdirxss_write(core, XSDIRX_EDH_ERRCNT_EN_REG, val);
> > +}
> > +
> > +static inline void xsdirx_setvidlockwindow(struct xsdirxss_core *core, u32
> val)
> > +{
> > + /*
> > + * The video lock window is the amount of time for which the
> > + * the mode and transport stream should be locked to get the
> > + * video lock interrupt.
> > + */
> > + xsdirxss_write(core, XSDIRX_VID_LOCK_WINDOW_REG, val);
> > +}
> > +
> > +static inline void xsdirx_disableintr(struct xsdirxss_core *core, u32 mask)
> > +{
> > + xsdirxss_clr(core, XSDIRX_IER_REG, mask);
> > +}
> > +
> > +static inline void xsdirx_enableintr(struct xsdirxss_core *core, u32 mask)
> > +{
> > + xsdirxss_set(core, XSDIRX_IER_REG, mask);
> > +}
> > +
> > +static void xsdirx_globalintr(struct xsdirxss_core *core, bool flag)
> > +{
> > + if (flag)
> > + xsdirxss_set(core, XSDIRX_GLBL_IER_REG,
> > + XSDIRX_GLBL_INTR_EN_MASK);
> > + else
> > + xsdirxss_clr(core, XSDIRX_GLBL_IER_REG,
> > + XSDIRX_GLBL_INTR_EN_MASK);
> > +}
> > +
> > +static inline void xsdirx_clearintr(struct xsdirxss_core *core, u32 mask)
> > +{
> > + xsdirxss_set(core, XSDIRX_ISR_REG, mask);
> > +}
> > +
> > +static void xsdirx_vid_bridge_control(struct xsdirxss_core *core,
> > + bool enable)
> > +{
> > + u32 mask = XSDIRX_RST_CTRL_SDIRX_BRIDGE_ENB_MASK;
> > +
> > + /*
> > + * TODO - Enable YUV444/RBG format in the bridge based
> > + * on BYTE3 color format.
> > + * XSDIRX_RST_CTRL_BRIDGE_CH_FMT_YUV444
> > + */
> > + if (enable)
> > + xsdirxss_set(core, XSDIRX_RST_CTRL_REG, mask);
> > + else
> > + xsdirxss_clr(core, XSDIRX_RST_CTRL_REG, mask);
> > +}
>
> This is only used in xsdirx_streamflow_control(), inlining it manually
> would be simpler I think.
>
Agree. I will update this in the next version.
> > +
> > +static void xsdirx_axis4_bridge_control(struct xsdirxss_core *core,
> > + bool enable)
> > +{
> > + if (enable)
> > + xsdirxss_set(core, XSDIRX_RST_CTRL_REG,
> > +
> XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK);
> > + else
> > + xsdirxss_clr(core, XSDIRX_RST_CTRL_REG,
> > +
> XSDIRX_RST_CTRL_VIDIN_AXI4S_MOD_ENB_MASK);
> > +}
>
> Same for this one.
>
Agree. I will update this in the next version.
> > +
> > +static void xsdirx_streamflow_control(struct xsdirxss_core *core, bool
> enable)
> > +{
> > + /* The sdi to native bridge is followed by native to axis4 bridge */
> > + if (enable) {
> > + xsdirx_axis4_bridge_control(core, enable);
> > + xsdirx_vid_bridge_control(core, enable);
> > + } else {
> > + xsdirx_vid_bridge_control(core, enable);
> > + xsdirx_axis4_bridge_control(core, enable);
> > + }
> > +}
> > +
> > +static void xsdirxss_get_framerate(struct v4l2_fract *frame_interval,
> > + u32 framerate)
> > +{
> > + switch (framerate) {
> > + case XSDIRX_TS_DET_STAT_RATE_23_98HZ:
> > + frame_interval->numerator = 1001;
> > + frame_interval->denominator = 24000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_24HZ:
> > + frame_interval->numerator = 1000;
> > + frame_interval->denominator = 24000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_25HZ:
> > + frame_interval->numerator = 1000;
> > + frame_interval->denominator = 25000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_29_97HZ:
> > + frame_interval->numerator = 1001;
> > + frame_interval->denominator = 30000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_30HZ:
> > + frame_interval->numerator = 1000;
> > + frame_interval->denominator = 30000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_47_95HZ:
> > + frame_interval->numerator = 1001;
> > + frame_interval->denominator = 48000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_48HZ:
> > + frame_interval->numerator = 1000;
> > + frame_interval->denominator = 48000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_50HZ:
> > + frame_interval->numerator = 1000;
> > + frame_interval->denominator = 50000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_59_94HZ:
> > + frame_interval->numerator = 1001;
> > + frame_interval->denominator = 60000;
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_60HZ:
> > + frame_interval->numerator = 1000;
> > + frame_interval->denominator = 60000;
> > + break;
> > + default:
> > + frame_interval->numerator = 1;
> > + frame_interval->denominator = 1;
> > + }
> > +}
> > +
> > +static void xsdirxss_set_gtclk(struct xsdirxss_state *state)
> > +{
> > + struct clk *gtclk;
> > + unsigned long clkrate;
> > + int ret, is_frac;
> > + struct xsdirxss_core *core = &state->core;
> > + u32 mode;
> > + static int prev_is_frac = -1;
> > +
> > + mode = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + mode &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> > +
> > + /*
> > + * TODO: For now, don't change the clock rate for any mode except
> 12G.
> > + * In future, configure gt clock for all modes and enable clock only
> > + * when needed (stream on/off).
> > + */
> > + if (mode != XSDIRX_MODE_12GI_MASK && mode !=
> XSDIRX_MODE_12GF_MASK)
> > + return;
> > +
> > + is_frac = state->frame_interval.numerator == 1001 ? 1 : 0;
> > +
> > + if (prev_is_frac == is_frac)
> > + return;
> > +
> > + xsdirx_core_disable(core);
> > + xsdirx_globalintr(core, false);
> > + xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
> > +
> > + /* get sdi_rx_clk */
> > + gtclk = core->clks[1].clk;
> > + clkrate = clk_get_rate(gtclk);
> > + is_frac = state->frame_interval.numerator == 1001 ? 1 : 0;
> > +
> > + /* calcualte clkrate */
>
> s/calcualte/calculate/
Will fix this in next version.
>
> > + if (!is_frac)
> > + clkrate = CLK_INT;
> > + else
> > + clkrate = (CLK_INT * 1000) / 1001;
>
> Shouldn't the clock rate also depend on the mode ? Table 3-2 lists
> different clock rates for HD-SDI and 12G-SDI.
>
There is a GT (gigabit transceiver PHY) IP which takes this clock from the onboard clock source like Si570
and generates the sdi_rx_clk required as per mode.
As mentioned in above comment, for all modes except 12G mode, the clock need not be changed from 148.5 MHz.
The GT block is capable of detecting integer as well as fractional frame rates in this case.
For 12G integer / fractional mode the clock needs to be 148.5 MHz / 148.5/1.001 MHz to correctly deliver the video.
Hence after detecting the mode(12G integer/fractional), the clock source is changed accordingly.
> > +
> > + ret = clk_set_rate(gtclk, clkrate);
> > + if (ret)
> > + dev_err(core->dev, "failed to set clk rate = %d\n", ret);
> > +
> > + clkrate = clk_get_rate(gtclk);
> > +
> > + dev_dbg(core->dev, "clkrate = %lu is_frac = %d\n",
> > + clkrate, is_frac);
> > +
> > + xsdirx_framer(core, state->framer_enable);
>
> As this is called in both the IRQ handler and the s_ctrl handler, you
> could have a race when accessing the XSDIRX_MDL_CTRL_REG register. You
> will need to protect all accesses to registers that are written from
> both the IRQ handler and userspace contexts with a spinlock.
>
Agree. This was missed. I will add the necessary spinlock.
> > + xsdirx_setedherrcnttrigger(core, state->edhmask);
> > + xsdirx_setvidlockwindow(core, state->vidlockwin);
> > + xsdirx_set_modedetect(core, state->searchmask);
> > + xsdirx_enableintr(core, XSDIRX_INTR_ALL_MASK);
> > + xsdirx_globalintr(core, true);
> > + xsdirx_core_enable(core);
> > +
> > + prev_is_frac = is_frac;
>
> That's lots of work done in an interrupt handler. As this function is
> called when a stream lock is detected, if the clock rate has to be
> changed, do I assume correctly that the resolution may have changed too
> ? That may require reconfiguring the pipeline and reallocating buffers.
> With SD and HD TV, I think the usual practice is to notify userspace of
> video lock and let it do the reconfiguration is required, instead of
> attempting to do so automatically. Hans, is that correct ? How would we
> handle then the case where the pipeline is already correctly configured
> with big enough buffers (I'm not sure this can actually happen, for the
> buffers yes, but for the pipeline configuration, maybe the format will
> always need to change) ?
>
> And I've now seen that we do emit the V4L2_EVENT_SRC_CH_RESOLUTION
> event
> :-) Do we thus need to reconfigure the IP core here ?
>
Yes we need to reconfigure the IP core and enable it here so that the core is running
but the bridges are disabled. With the SDI Rx core enabled, we will get to know when a new stream has started and its properties.
The application will be notified of this and it can query for the stream properties to accordingly setup the pipeline.
With the bridges disabled, the downstream IPs will not be able to receive any data.
> > +}
> > +
> > +/**
> > + * xsdirx_get_stream_properties - Get SDI Rx stream properties
> > + * @state: pointer to driver state
> > + *
> > + * This function decodes the stream's ST352 payload (if available) to get
> > + * stream properties like width, height, picture type
> (interlaced/progressive),
> > + * etc.
> > + *
> > + * Return: 0 for success else errors
> > + */
> > +static int xsdirx_get_stream_properties(struct xsdirxss_state *state)
> > +{
> > + struct xsdirxss_core *core = &state->core;
> > + struct device *dev = core->dev;
> > + u32 mode, payload = 0, val, family, valid, tscan;
> > + u8 byte1 = 0, active_luma = 0, pic_type = 0, framerate = 0;
> > + u8 sampling = XST352_BYTE3_COLOR_FORMAT_422;
> > + struct v4l2_mbus_framefmt *format = &state->format;
> > + u32 bpc = XST352_BYTE4_BIT_DEPTH_10;
> > +
> > + mode = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + mode &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> > +
> > + valid = xsdirxss_read(core, XSDIRX_ST352_VALID_REG);
> > +
> > + if (mode >= XSDIRX_MODE_3G_MASK && !valid) {
> > + dev_err(dev, "No valid ST352 payload present even for 3G
> mode and above\n");
> > + return -EINVAL;
> > + }
> > +
> > + val = xsdirxss_read(core, XSDIRX_TS_DET_STAT_REG);
> > + if (valid & XSDIRX_ST352_VALID_DS1_MASK) {
> > + payload = xsdirxss_read(core, XSDIRX_ST352_DS1_REG);
> > + byte1 = rshift_and_mask(payload, XST352_PAYLOAD_BYTE1);
> > + active_luma = mask_and_rshift(payload,
> > +
> XST352_BYTE3_ACT_LUMA_COUNT);
> > + pic_type = mask_and_rshift(payload,
> XST352_BYTE2_PIC_TYPE);
> > + framerate = rshift_and_mask(payload, XST352_BYTE2_FPS);
> > + tscan = mask_and_rshift(payload, XST352_BYTE2_TS_TYPE);
> > + sampling = mask_and_rshift(payload,
> XST352_BYTE3_COLOR_FORMAT);
> > + bpc = mask_and_rshift(payload, XST352_BYTE4_BIT_DEPTH);
> > + } else {
> > + dev_dbg(dev, "No ST352 payload available : Mode = %d\n",
> mode);
> > + framerate = mask_and_rshift(val,
> XSDIRX_TS_DET_STAT_RATE);
> > + tscan = mask_and_rshift(val, XSDIRX_TS_DET_STAT_SCAN);
> > + }
> > +
> > + if ((bpc == XST352_BYTE4_BIT_DEPTH_10 && core->bpc != 10) ||
> > + (bpc == XST352_BYTE4_BIT_DEPTH_12 && core->bpc != 12)) {
> > + dev_dbg(dev, "Bit depth not supported. bpc = %d core->bpc =
> %d\n",
> > + bpc, core->bpc);
> > + return -EINVAL;
> > + }
> > +
> > + family = mask_and_rshift(val, XSDIRX_TS_DET_STAT_FAMILY);
> > + state->ts_is_interlaced = tscan ? false : true;
> > +
> > + dev_dbg(dev, "ts_is_interlaced = %d, family = %d\n",
> > + state->ts_is_interlaced, family);
> > +
> > + switch (mode) {
> > + case XSDIRX_MODE_HD_MASK:
> > + if (!valid) {
> > + /* No payload obtained */
> > + dev_dbg(dev, "frame rate : %d, tscan = %d\n",
> > + framerate, tscan);
> > + /*
> > + * NOTE : A progressive segmented frame pSF will be
> > + * reported incorrectly as Interlaced as we rely on IP's
> > + * transport scan locked bit.
> > + */
> > + dev_warn(dev, "pSF will be incorrectly reported as
> Interlaced\n");
> > +
> > + switch (framerate) {
> > + case XSDIRX_TS_DET_STAT_RATE_23_98HZ:
> > + case XSDIRX_TS_DET_STAT_RATE_24HZ:
> > + case XSDIRX_TS_DET_STAT_RATE_25HZ:
> > + case XSDIRX_TS_DET_STAT_RATE_29_97HZ:
> > + case XSDIRX_TS_DET_STAT_RATE_30HZ:
> > + if (family == XSDIRX_SMPTE_ST_296) {
> > + format->width = 1280;
> > + format->height = 720;
> > + format->field = V4L2_FIELD_NONE;
> > + } else if (family == XSDIRX_SMPTE_ST_2048_2)
> {
> > + format->width = 2048;
> > + format->height = 1080;
> > + if (tscan)
> > + format->field =
> V4L2_FIELD_NONE;
> > + else
> > + format->field =
> > +
> V4L2_FIELD_ALTERNATE;
> > + } else {
> > + format->width = 1920;
> > + format->height = 1080;
> > + if (tscan)
> > + format->field =
> V4L2_FIELD_NONE;
> > + else
> > + format->field =
> > +
> V4L2_FIELD_ALTERNATE;
> > + }
> > + break;
> > + case XSDIRX_TS_DET_STAT_RATE_50HZ:
> > + case XSDIRX_TS_DET_STAT_RATE_59_94HZ:
> > + case XSDIRX_TS_DET_STAT_RATE_60HZ:
> > + if (family == XSDIRX_SMPTE_ST_274) {
> > + format->width = 1920;
> > + format->height = 1080;
> > + } else {
> > + format->width = 1280;
> > + format->height = 720;
> > + }
> > + format->field = V4L2_FIELD_NONE;
> > + break;
> > + default:
> > + format->width = 1920;
> > + format->height = 1080;
> > + format->field = V4L2_FIELD_NONE;
> > + }
> > + } else {
> > + dev_dbg(dev, "Got the payload\n");
> > + switch (byte1) {
> > + case XST352_BYTE1_ST292_1x720L_1_5G:
> > + /* SMPTE ST 292-1 for 720 line payloads */
> > + format->width = 1280;
> > + format->height = 720;
> > + break;
> > + case XST352_BYTE1_ST292_1x1080L_1_5G:
> > + /* SMPTE ST 292-1 for 1080 line payloads */
> > + format->height = 1080;
> > + if (active_luma)
> > + format->width = 2048;
> > + else
> > + format->width = 1920;
> > + break;
> > + default:
> > + dev_dbg(dev, "Unknown HD Mode SMPTE
> standard\n");
> > + return -EINVAL;
> > + }
> > + }
> > + break;
> > + case XSDIRX_MODE_SD_MASK:
> > + format->field = V4L2_FIELD_ALTERNATE;
> > +
> > + switch (family) {
> > + case XSDIRX_NTSC:
> > + format->width = 720;
> > + format->height = 486;
> > + break;
> > + case XSDIRX_PAL:
> > + format->width = 720;
> > + format->height = 576;
> > + break;
> > + default:
> > + dev_dbg(dev, "Unknown SD Mode SMPTE standard\n");
> > + return -EINVAL;
> > + }
> > + break;
> > + case XSDIRX_MODE_3G_MASK:
> > + switch (byte1) {
> > + case XST352_BYTE1_ST425_2008_750L_3GB:
> > + /* Sec 4.1.6.1 SMPTE 425-2008 */
> > + case XST352_BYTE1_ST372_2x720L_3GB:
> > + /* Table 13 SMPTE 425-2008 */
> > + format->width = 1280;
> > + format->height = 720;
> > + break;
> > + case XST352_BYTE1_ST425_2008_1125L_3GA:
> > + /* ST352 Table SMPTE 425-1 */
> > + case XST352_BYTE1_ST372_DL_3GB:
> > + /* Table 13 SMPTE 425-2008 */
> > + case XST352_BYTE1_ST372_2x1080L_3GB:
> > + /* Table 13 SMPTE 425-2008 */
> > + format->height = 1080;
> > + if (active_luma)
> > + format->width = 2048;
> > + else
> > + format->width = 1920;
> > + break;
> > + default:
> > + dev_dbg(dev, "Unknown 3G Mode SMPTE standard\n");
> > + return -EINVAL;
> > + }
> > + break;
> > + case XSDIRX_MODE_6G_MASK:
> > + switch (byte1) {
> > + case XST352_BYTE1_ST2081_10_DL_2160L_6G:
> > + /* Dual link 6G */
> > + case XST352_BYTE1_ST2081_10_2160L_6G:
> > + /* Table 3 SMPTE ST 2081-10 */
> > + format->height = 2160;
> > + if (active_luma)
> > + format->width = 4096;
> > + else
> > + format->width = 3840;
> > + break;
> > + case XST352_BYTE1_ST2081_10_2_1080L_6G:
> > + format->height = 1080;
> > + if (active_luma)
> > + format->width = 2048;
> > + else
> > + format->width = 1920;
> > + break;
> > + default:
> > + dev_dbg(dev, "Unknown 6G Mode SMPTE standard\n");
> > + return -EINVAL;
> > + }
> > + break;
> > + case XSDIRX_MODE_12GI_MASK:
> > + case XSDIRX_MODE_12GF_MASK:
> > + switch (byte1) {
> > + case XST352_BYTE1_ST2082_10_2160L_12G:
> > + /* Section 4.3.1 SMPTE ST 2082-10 */
> > + format->height = 2160;
> > + if (active_luma)
> > + format->width = 4096;
> > + else
> > + format->width = 3840;
> > + break;
> > + default:
> > + dev_dbg(dev, "Unknown 12G Mode SMPTE
> standard\n");
> > + return -EINVAL;
> > + }
> > + break;
> > + default:
> > + dev_err(dev, "Invalid Mode\n");
> > + return -EINVAL;
> > + }
> > +
> > + if (valid) {
> > + if (pic_type)
> > + format->field = V4L2_FIELD_NONE;
> > + else
> > + format->field = V4L2_FIELD_ALTERNATE;
> > +
> > + if (format->height == 1080 && pic_type && !tscan)
> > + format->field = V4L2_FIELD_ALTERNATE;
> > +
> > + /*
> > + * In 3GB DL pSF mode the video is similar to interlaced.
> > + * So though it is a progressive video, its transport is
> > + * interlaced and is sent as two width x (height/2) buffers.
> > + */
> > + if (byte1 == XST352_BYTE1_ST372_DL_3GB) {
> > + if (state->ts_is_interlaced)
> > + format->field = V4L2_FIELD_ALTERNATE;
> > + else
> > + format->field = V4L2_FIELD_NONE;
> > + }
> > + }
> > +
> > + if (format->field == V4L2_FIELD_ALTERNATE)
> > + format->height = format->height / 2;
> > +
> > + switch (sampling) {
> > + case XST352_BYTE3_COLOR_FORMAT_422:
> > + if (core->bpc == 10)
> > + format->code = MEDIA_BUS_FMT_UYVY10_1X20;
> > + else
> > + format->code = MEDIA_BUS_FMT_UYVY12_1X24;
> > + break;
> > + case XST352_BYTE3_COLOR_FORMAT_420:
> > + case XST352_BYTE3_COLOR_FORMAT_YUV444:
> > + case XST352_BYTE3_COLOR_FORMAT_GBR:
> > + format->code = 0;
> > + dev_dbg(dev, "No corresponding media bus formats\n");
> > + break;
> > + default:
> > + dev_err(dev, "Unsupported color format : %d\n", sampling);
> > + return -EINVAL;
> > + }
> > +
> > + xsdirxss_get_framerate(&state->frame_interval, framerate);
> > +
> > + dev_dbg(dev, "Stream width = %d height = %d Field = %d payload =
> 0x%08x ts = 0x%08x\n",
> > + format->width, format->height, format->field, payload, val);
> > + dev_dbg(dev, "frame rate numerator = %d denominator = %d\n",
> > + state->frame_interval.numerator,
> > + state->frame_interval.denominator);
> > + dev_dbg(dev, "Stream code = 0x%x\n", format->code);
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_irq_handler - Interrupt handler for SDI Rx
> > + * @irq: IRQ number
> > + * @dev_id: Pointer to device state
> > + *
> > + * The SDI Rx interrupts are cleared by writing 1 to corresponding bit.
> > + *
> > + * Return: IRQ_HANDLED after handling interrupts
> > + */
> > +static irqreturn_t xsdirxss_irq_handler(int irq, void *dev_id)
> > +{
> > + struct xsdirxss_state *state = (struct xsdirxss_state *)dev_id;
> > + struct xsdirxss_core *core = &state->core;
> > + struct device *dev = core->dev;
> > + u32 status;
> > +
> > + status = xsdirxss_read(core, XSDIRX_ISR_REG);
> > + xsdirxss_write(core, XSDIRX_ISR_REG, status);
> > + dev_dbg(dev, "interrupt status = 0x%08x\n", status);
> > +
> > + if (status & XSDIRX_INTR_VIDLOCK_MASK ||
> > + status & XSDIRX_INTR_VIDUNLOCK_MASK) {
> > + u32 val1, val2;
> > +
> > + dev_dbg(dev, "video lock/unlock interrupt\n");
> > +
> > + xsdirx_streamflow_control(core, false);
> > + state->streaming = false;
> > +
> > + val1 = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + val2 = xsdirxss_read(core, XSDIRX_TS_DET_STAT_REG);
> > +
> > + if ((val1 & XSDIRX_MODE_DET_STAT_MODE_LOCK_MASK) &&
> > + (val2 & XSDIRX_TS_DET_STAT_LOCKED_MASK)) {
> > + u32 mask =
> XSDIRX_RST_CTRL_RST_CRC_ERRCNT_MASK |
> > +
> XSDIRX_RST_CTRL_RST_EDH_ERRCNT_MASK;
> > +
> > + dev_dbg(dev, "video lock interrupt\n");
> > +
> > + xsdirxss_set(core, XSDIRX_RST_CTRL_REG, mask);
> > + xsdirxss_clr(core, XSDIRX_RST_CTRL_REG, mask);
> > +
> > + val1 = xsdirxss_read(core, XSDIRX_ST352_VALID_REG);
> > + val2 = xsdirxss_read(core, XSDIRX_ST352_DS1_REG);
> > +
> > + dev_dbg(dev, "valid st352 mask = 0x%08x\n", val1);
> > + dev_dbg(dev, "st352 payload = 0x%08x\n", val2);
> > +
> > + if (!xsdirx_get_stream_properties(state)) {
> > + state->vidlocked = true;
> > + xsdirxss_set_gtclk(state);
> > + } else {
> > + dev_err(dev, "Unable to get stream
> properties!\n");
> > + state->vidlocked = false;
> > + }
> > + } else {
> > + dev_dbg(dev, "video unlock interrupt\n");
> > + state->vidlocked = false;
> > + }
> > +
> > + memset(&state->event, 0, sizeof(state->event));
> > + state->event.type = V4L2_EVENT_SOURCE_CHANGE;
> > + state->event.u.src_change.changes =
> > + V4L2_EVENT_SRC_CH_RESOLUTION;
> > + v4l2_subdev_notify_event(&state->subdev, &state->event);
> > + }
> > +
> > + if (status & XSDIRX_INTR_UNDERFLOW_MASK) {
> > + dev_dbg(dev, "Video in to AXI4 Stream core underflow
> interrupt\n");
> > +
> > + memset(&state->event, 0, sizeof(state->event));
> > + state->event.type = V4L2_EVENT_XILINX_SDIRX_UNDERFLOW;
> > + v4l2_subdev_notify_event(&state->subdev, &state->event);
> > + }
> > +
> > + if (status & XSDIRX_INTR_OVERFLOW_MASK) {
> > + dev_dbg(dev, "Video in to AXI4 Stream core overflow
> interrupt\n");
> > +
> > + memset(&state->event, 0, sizeof(state->event));
> > + state->event.type = V4L2_EVENT_XILINX_SDIRX_OVERFLOW;
> > + v4l2_subdev_notify_event(&state->subdev, &state->event);
> > + }
>
> Can't we combine these two in a single event type, with underflow and
> overflow reported in the event payload in a bitmask ?
>
Yes we can. I will combine these two into a single event in the next version.
> > + return IRQ_HANDLED;
> > +}
> > +
> > +/**
> > + * xsdirxss_subscribe_event - Subscribe to video lock and unlock event
> > + * @sd: V4L2 Sub device
> > + * @fh: V4L2 File Handle
> > + * @sub: Subcribe event structure
> > + *
> > + * Return: 0 on success, errors otherwise
> > + */
> > +static int xsdirxss_subscribe_event(struct v4l2_subdev *sd,
> > + struct v4l2_fh *fh,
> > + struct v4l2_event_subscription *sub)
> > +{
> > + int ret;
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > +
> > + switch (sub->type) {
> > + case V4L2_EVENT_XILINX_SDIRX_UNDERFLOW:
> > + case V4L2_EVENT_XILINX_SDIRX_OVERFLOW:
> > + ret = v4l2_event_subscribe(fh, sub, XSDIRX_MAX_EVENTS,
> NULL);
> > + break;
> > + case V4L2_EVENT_SOURCE_CHANGE:
> > + ret = v4l2_src_change_event_subscribe(fh, sub);
> > + break;
> > + default:
> > + return -EINVAL;
>
> As Hans commented, you need to call v4l2_ctrl_subscribe_event() here.
>
Agree. I will add this in next revision.
> > + }
> > + dev_dbg(core->dev, "Event subscribed : 0x%08x\n", sub->type);
> > + return ret;
> > +}
> > +
> > +/**
> > + * xsdirxss_unsubscribe_event - Unsubscribe from all events registered
> > + * @sd: V4L2 Sub device
> > + * @fh: V4L2 file handle
> > + * @sub: pointer to Event unsubscription structure
> > + *
> > + * Return: zero on success, else a negative error code.
> > + */
> > +static int xsdirxss_unsubscribe_event(struct v4l2_subdev *sd,
> > + struct v4l2_fh *fh,
> > + struct v4l2_event_subscription *sub)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > +
> > + dev_dbg(core->dev, "Event unsubscribe : 0x%08x\n", sub->type);
> > + return v4l2_event_unsubscribe(fh, sub);
> > +}
>
> I think you can drop this function and use v4l2_event_subdev_unsubscribe
> as the ..unsubscribe_event() handler.
>
Agree I will remove this in next version.
> > +
> > +/**
> > + * xsdirxss_s_ctrl - This is used to set the Xilinx SDI Rx V4L2 controls
> > + * @ctrl: V4L2 control to be set
> > + *
> > + * This function is used to set the V4L2 controls for the Xilinx SDI Rx
> > + * Subsystem.
> > + *
> > + * Return: 0 on success, errors otherwise
> > + */
> > +static int xsdirxss_s_ctrl(struct v4l2_ctrl *ctrl)
> > +{
> > + int ret = 0;
> > + struct xsdirxss_state *xsdirxss =
> > + container_of(ctrl->handler, struct xsdirxss_state,
> > + ctrl_handler);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > + struct device *dev = core->dev;
> > +
> > + dev_dbg(dev, "set ctrl id = 0x%08x val = 0x%08x\n",
> > + ctrl->id, ctrl->val);
> > +
> > + if (xsdirxss->streaming) {
> > + dev_err(dev, "Cannot set controls while streaming\n");
> > + return -EINVAL;
> > + }
> > +
> > + xsdirx_core_disable(core);
> > + switch (ctrl->id) {
> > + case V4L2_CID_XILINX_SDIRX_FRAMER:
> > + xsdirx_framer(core, ctrl->val);
> > + xsdirxss->framer_enable = ctrl->val;
> > + break;
> > + case V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW:
> > + xsdirx_setvidlockwindow(core, ctrl->val);
> > + xsdirxss->vidlockwin = ctrl->val;
> > + break;
> > + case V4L2_CID_XILINX_SDIRX_EDH_ERRCNT_ENABLE:
>
> As this is used to select which error sources to enable, how about
> naming the control V4L2_CID_XILINX_SDIRX_EDH_ERROR_SOURCES or
> V4L2_CID_XILINX_SDIRX_EDH_ERRORS_MASK ?
>
Ok. I will rename this to V4L2_CID_XILINX_SDIRX_EDH_ERROR_SOURCES
> > + xsdirx_setedherrcnttrigger(core, ctrl->val);
> > + xsdirxss->edhmask = ctrl->val;
> > + break;
> > + case V4L2_CID_XILINX_SDIRX_SEARCH_MODES:
> > + if (ctrl->val) {
> > + if (core->mode == XSDIRXSS_SDI_STD_3G) {
> > + dev_dbg(dev, "Upto 3G supported\n");
> > + ctrl->val &= ~(BIT(XSDIRX_MODE_6G_OFFSET)
> |
> > + BIT(XSDIRX_MODE_12GI_OFFSET)
> |
> > +
> BIT(XSDIRX_MODE_12GF_OFFSET));
> > + }
> > +
> > + if (core->mode == XSDIRXSS_SDI_STD_6G) {
> > + dev_dbg(dev, "Upto 6G supported\n");
> > + ctrl->val &=
> ~(BIT(XSDIRX_MODE_12GI_OFFSET) |
> > +
> BIT(XSDIRX_MODE_12GF_OFFSET));
> > + }
> > +
> > + ret = xsdirx_set_modedetect(core, ctrl->val);
> > + if (!ret)
> > + xsdirxss->searchmask = ctrl->val;
> > + } else {
> > + dev_err(dev, "Select at least one mode!\n");
> > + return -EINVAL;
> > + }
> > + break;
>
> The traditional approach to select timing standards is to use ioctls.
> Hans, do you think a custom control is fine here, or should the dv
> timings ioctls be extended (or new sdi timings ioctls created) ?
>
> If we go for a single control, I'm a bit concerned that this control
> will restrict the search when multiple bits are set, but force a
> specific mode when a single bit is set. I don't have enough experience
> with SDI to tell whether this is the right behaviour.
>
> > + default:
> > + xsdirxss_set(core, XSDIRX_RST_CTRL_REG,
> > + XSDIRX_RST_CTRL_SS_EN_MASK);
> > + return -EINVAL;
>
> This looks weird.
>
> ret = -EINVAL;
> break;
>
> would be better.
>
Agree. I will fix this.
> > + }
> > + xsdirx_core_enable(core);
>
> Do we really need to disable and reenable the core as we're guaranteed
> not to be streaming ?
>
The SDI Rx core will always be enabled to be able to understand what is the incoming stream properties.
During stream on/off we only enable/disable the video bridges which convert the SDI stream to AXI4-S
and pass to downstream IP.
If the SDI Rx core isn't enabled before stream_on, the stream properties (mode, width, height, frame rate, etc) won't be known
to the driver and hence the application.
> > + return ret;
> > +}
> > +
> > +/**
> > + * xsdirxss_g_volatile_ctrl - get the Xilinx SDI Rx controls
> > + * @ctrl: Pointer to V4L2 control
> > + *
> > + * Return: 0 on success, errors otherwise
> > + */
> > +static int xsdirxss_g_volatile_ctrl(struct v4l2_ctrl *ctrl)
> > +{
> > + u32 val;
> > + struct xsdirxss_state *xsdirxss =
> > + container_of(ctrl->handler,
> > + struct xsdirxss_state, ctrl_handler);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > + struct device *dev = core->dev;
> > +
> > + switch (ctrl->id) {
> > + case V4L2_CID_XILINX_SDIRX_MODE_DETECT:
> > + if (!xsdirxss->vidlocked) {
> > + dev_err(dev, "Can't get values when video not
> locked!\n");
> > + return -EINVAL;
> > + }
> > + val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> > +
> > + switch (val) {
> > + case XSDIRX_MODE_SD_MASK:
> > + ctrl->val = XSDIRX_MODE_SD_OFFSET;
> > + break;
> > + case XSDIRX_MODE_HD_MASK:
> > + ctrl->val = XSDIRX_MODE_HD_OFFSET;
> > + break;
> > + case XSDIRX_MODE_3G_MASK:
> > + ctrl->val = XSDIRX_MODE_3G_OFFSET;
> > + break;
> > + case XSDIRX_MODE_6G_MASK:
> > + ctrl->val = XSDIRX_MODE_6G_OFFSET;
> > + break;
> > + case XSDIRX_MODE_12GI_MASK:
> > + ctrl->val = XSDIRX_MODE_12GI_OFFSET;
> > + break;
> > + case XSDIRX_MODE_12GF_MASK:
> > + ctrl->val = XSDIRX_MODE_12GF_OFFSET;
> > + break;
> > + }
> > + break;
>
> Hans commented that the dv timings structure will report whether the
> mode is interlaced, I wonder if reporting the SDI mode shouldn't go
> through that structure too.
>
I don’t know about this.
We may add a feature in V4L2 / DRM framework to set / get the SDI modes.
> > + case V4L2_CID_XILINX_SDIRX_CRC:
> > + ctrl->val = xsdirxss_read(core, XSDIRX_CRC_ERRCNT_REG);
> > + xsdirxss_write(core, XSDIRX_CRC_ERRCNT_REG, 0xFFFF);
> > + break;
>
> Are CRC errors common (and recoverable), or are they rare and fatal
> errors ? In other words, does this report information that would be
> classified as link quality, or fatal errors ? In the later case I wonder
> if an event wouldn't make more sense. It could be reported as another
> bit in the overflow/underflow event.
>
CRC errors will reflect link quality.
There is no interrupt for CRC errors.
So driver software won't know when to read this register.
Also this is specific to Xilinx implementation.
> > + case V4L2_CID_XILINX_SDIRX_EDH_ERRCNT:
> > + val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> > + if (val == XSDIRX_MODE_SD_MASK) {
> > + ctrl->val = xsdirxss_read(core,
> XSDIRX_EDH_ERRCNT_REG);
> > + } else {
> > + dev_dbg(dev, "%d - not in SD mode\n", ctrl->id);
> > + return -EINVAL;
> > + }
> > + break;
>
> If my understanding of the datasheet is correct, this will be reset for
> every frame, right ? Reporting the information this way is thus quite
> racy. Isn't it better to send it through an event ?
>
This is not reset per frame.
This is an error reporting mechanism that application can use to get errors in stream while
running SD modes (720x487 and 720x576).
So I think it is ok to send it like this.
> > + case V4L2_CID_XILINX_SDIRX_EDH_STATUS:
> > + val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + val &= XSDIRX_MODE_DET_STAT_RX_MODE_MASK;
> > + if (val == XSDIRX_MODE_SD_MASK) {
> > + ctrl->val = xsdirxss_read(core,
> XSDIRX_EDH_STAT_REG);
> > + } else {
> > + dev_dbg(dev, "%d - not in SD mode\n", ctrl->id);
> > + return -EINVAL;
> > + }
> > + break;
>
> Same here, seems quite racy.
>
Same here as earlier about EDH Counter. There is no interrupt here too.
> > + case V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED:
> > + if (!xsdirxss->vidlocked) {
> > + dev_err(dev, "Can't get values when video not
> locked!\n");
> > + return -EINVAL;
> > + }
> > + ctrl->val = xsdirxss->ts_is_interlaced;
> > + break;
> > + case V4L2_CID_XILINX_SDIRX_ACTIVE_STREAMS:
> > + if (!xsdirxss->vidlocked) {
> > + dev_err(dev, "Can't get values when video not
> locked!\n");
> > + return -EINVAL;
> > + }
> > + val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + val &= XSDIRX_MODE_DET_STAT_ACT_STREAM_MASK;
> > + val >>= XSDIRX_MODE_DET_STAT_ACT_STREAM_OFFSET;
> > + ctrl->val = 1 << val;
> > + break;
> > + case V4L2_CID_XILINX_SDIRX_IS_3GB:
> > + if (!xsdirxss->vidlocked) {
> > + dev_err(dev, "Can't get values when video not
> locked!\n");
> > + return -EINVAL;
> > + }
> > + val = xsdirxss_read(core, XSDIRX_MODE_DET_STAT_REG);
> > + val &= XSDIRX_MODE_DET_STAT_LVLB_3G_MASK;
> > + ctrl->val = val ? true : false;
> > + break;
>
> Shouldn't this also go through DV timings ? If not, I think it should at
> least be combined with V4L2_CID_XILINX_SDIRX_MODE_DETECT.
>
I am trying to use the same values to set mode and detect it.
As there is no different bit to specifically detect 3GB Mode, hence this differentiation is there.
I will try to combine this in later patch.
> > + default:
> > + dev_err(dev, "Get Invalid control id 0x%0x\n", ctrl->id);
> > + return -EINVAL;
> > + }
> > + dev_dbg(dev, "Get ctrl id = 0x%08x val = 0x%08x\n", ctrl->id,
> > + ctrl->val);
>
> I would drop this line.
>
Ok I will remove this in next patch.
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_log_status - Logs the status of the SDI Rx Subsystem
> > + * @sd: Pointer to V4L2 subdevice structure
> > + *
> > + * This function prints the current status of Xilinx SDI Rx Subsystem
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xsdirxss_log_status(struct v4l2_subdev *sd)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > + u32 i;
> > +
> > + v4l2_info(sd, "***** SDI Rx subsystem reg dump start *****\n");
> > + for (i = 0; i < 0x28; i++) {
>
> There are registers in this range that are not documented in the
> datasheet. Is it really safe to read them ? There are also registers
> that are of no real interest I believe (ISR for instance), or registers
> that seems to map to a FIFO (RX_ST352_DATA_DS*) which may cause issue
> when read as the IRQ handler extracts data from them (I could be wrong
> here though). Should this be restricted to a handful of carefully
> selected registers ? You could then also print their name instead of
> their address, that would be more readable.
>
Ok. I will print registers values with register names and offsets in next version.
> > + u32 data;
> > +
> > + data = xsdirxss_read(core, i * 4);
> > + v4l2_info(sd, "offset 0x%08x data 0x%08x\n",
> > + i * 4, data);
> > + }
> > + v4l2_info(sd, "***** SDI Rx subsystem reg dump end *****\n");
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_g_frame_interval - Get the frame interval
> > + * @sd: V4L2 Sub device
> > + * @fi: Pointer to V4l2 Sub device frame interval structure
> > + *
> > + * This function is used to get the frame interval.
> > + * The frame rate can be integral or fractional.
> > + * Integral frame rate e.g. numerator = 1000, denominator = 24000 => 24
> fps
> > + * Fractional frame rate e.g. numerator = 1001, denominator = 24000 =>
> 23.97 fps
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xsdirxss_g_frame_interval(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_frame_interval *fi)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > +
> > + if (!xsdirxss->vidlocked) {
> > + dev_err(core->dev, "Video not locked!\n");
> > + return -EINVAL;
> > + }
> > +
> > + fi->interval = xsdirxss->frame_interval;
>
> There's a data race with the interrupt handler here.
>
Yes I will fix this in next version.
> > +
> > + dev_dbg(core->dev, "frame rate numerator = %d denominator = %d\n",
> > + xsdirxss->frame_interval.numerator,
> > + xsdirxss->frame_interval.denominator);
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_s_stream - It is used to start/stop the streaming.
> > + * @sd: V4L2 Sub device
> > + * @enable: Flag (True / False)
> > + *
> > + * This function controls the start or stop of streaming for the
> > + * Xilinx SDI Rx Subsystem.
> > + *
> > + * Return: 0 on success, errors otherwise
> > + */
> > +static int xsdirxss_s_stream(struct v4l2_subdev *sd, int enable)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > + struct device *dev = core->dev;
> > +
>
> Maybe
>
> if (enable == xsdirxss->streaming) {
> dev_dbg(...);
> return enable ? -EINVAL : 0;
> }
>
> ? Up to you.
>
Agree. This will be similar to MIPI CSI-2 Rx driver then.
I will fix this in next version.
> > + if (enable) {
> > + if (!xsdirxss->vidlocked) {
> > + dev_dbg(dev, "Video is not locked\n");
> > + return -EINVAL;
> > + }
> > + if (xsdirxss->streaming) {
> > + dev_dbg(dev, "Already streaming\n");
> > + return -EINVAL;
> > + }
> > +
> > + xsdirx_streamflow_control(core, true);
> > + xsdirxss->streaming = true;
> > + dev_dbg(dev, "Streaming started\n");
> > + } else {
> > + if (!xsdirxss->streaming) {
> > + dev_dbg(dev, "Stopped streaming already\n");
> > + return 0;
> > + }
> > +
> > + xsdirx_streamflow_control(core, false);
> > + xsdirxss->streaming = false;
> > + dev_dbg(dev, "Streaming stopped\n");
> > + }
> > +
>
> And possibly
>
> xsdirxss->streaming = enable;
> dev_dbg(dev, "Streaming %s\", enable ? "started" : "stopped");
>
Agree to this too. I will update this in next version.
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_g_input_status - It is used to determine if the video signal
> > + * is present / locked onto or not.
> > + *
> > + * @sd: V4L2 Sub device
> > + * @status: status of signal locked
> > + *
> > + * This is used to determine if the video signal is present and locked onto
> > + * by the SDI Rx core or not based on vidlocked flag.
> > + *
> > + * Return: zero on success
> > + */
> > +static int xsdirxss_g_input_status(struct v4l2_subdev *sd, u32 *status)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > +
> > + if (!xsdirxss->vidlocked)
> > + *status = V4L2_IN_ST_NO_SYNC | V4L2_IN_ST_NO_SIGNAL;
> > + else
> > + *status = 0;
> > +
> > + return 0;
> > +}
> > +
> > +static struct v4l2_mbus_framefmt *
> > +__xsdirxss_get_pad_format(struct xsdirxss_state *xsdirxss,
> > + struct v4l2_subdev_pad_config *cfg,
> > + unsigned int pad, u32 which)
> > +{
> > + switch (which) {
> > + case V4L2_SUBDEV_FORMAT_TRY:
> > + return v4l2_subdev_get_try_format(&xsdirxss->subdev, cfg,
> pad);
> > + case V4L2_SUBDEV_FORMAT_ACTIVE:
> > + return &xsdirxss->format;
> > + default:
> > + return NULL;
> > + }
> > +}
> > +
> > +/**
> > + * xsdirxss_init_cfg - Initialise the pad format config to default
> > + * @sd: Pointer to V4L2 Sub device structure
> > + * @cfg: Pointer to sub device pad information structure
> > + *
> > + * This function is used to initialize the pad format with the default
> > + * values.
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xsdirxss_init_cfg(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + struct v4l2_mbus_framefmt *format;
> > +
> > + format = v4l2_subdev_get_try_format(sd, cfg, 0);
> > + *format = xsdirxss->default_format;
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_get_format - Get the pad format
> > + * @sd: Pointer to V4L2 Sub device structure
> > + * @cfg: Pointer to sub device pad information structure
> > + * @fmt: Pointer to pad level media bus format
> > + *
> > + * This function is used to get the pad format information.
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xsdirxss_get_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *fmt)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > +
> > + if (!xsdirxss->vidlocked) {
> > + dev_err(core->dev, "Video not locked!\n");
> > + return -EINVAL;
> > + }
> > +
> > + fmt->format = *__xsdirxss_get_pad_format(xsdirxss, cfg,
> > + fmt->pad, fmt->which);
> > +
> > + dev_dbg(core->dev, "Stream width = %d height = %d Field = %d\n",
> > + fmt->format.width, fmt->format.height, fmt->format.field);
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_set_format - This is used to set the pad format
> > + * @sd: Pointer to V4L2 Sub device structure
> > + * @cfg: Pointer to sub device pad information structure
> > + * @fmt: Pointer to pad level media bus format
> > + *
> > + * This function is used to set the pad format.
> > + * Since the pad format is fixed in hardware, it can't be
> > + * modified on run time.
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xsdirxss_set_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *fmt)
> > +{
> > + struct v4l2_mbus_framefmt *__format;
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > +
> > + dev_dbg(xsdirxss->core.dev,
> > + "set width %d height %d code %d field %d colorspace %d\n",
> > + fmt->format.width, fmt->format.height,
> > + fmt->format.code, fmt->format.field,
> > + fmt->format.colorspace);
> > +
> > + __format = __xsdirxss_get_pad_format(xsdirxss, cfg,
> > + fmt->pad, fmt->which);
> > +
> > + /* Currently reset the code to one fixed in hardware */
> > + /* TODO : Add checks for width height */
> > + fmt->format.code = __format->code;
>
> As Hans requested, width, height and field should be set here too, and
> probably colorspace information too.
>
Yes. I will be updating this in next version.
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_enum_mbus_code - Handle pixel format enumeration
> > + * @sd: pointer to v4l2 subdev structure
> > + * @cfg: V4L2 subdev pad configuration
> > + * @code: pointer to v4l2_subdev_mbus_code_enum structure
> > + *
> > + * Return: -EINVAL or zero on success
> > + */
> > +static int xsdirxss_enum_mbus_code(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_mbus_code_enum
> *code)
> > +{
> > + struct xsdirxss_state *xsdirxss = to_xsdirxssstate(sd);
> > + u32 index = code->index;
> > + u32 maxindex;
> > +
> > + if (xsdirxss->core.bpc == 10)
> > + maxindex = ARRAY_SIZE(xsdirxss_10bpc_mbus_fmts);
> > + else
> > + maxindex = ARRAY_SIZE(xsdirxss_12bpc_mbus_fmts);
> > +
> > + if (code->pad || index >= maxindex)
> > + return -EINVAL;
> > +
> > + if (xsdirxss->core.bpc == 10)
> > + code->code = xsdirxss_10bpc_mbus_fmts[index];
> > + else
> > + code->code = xsdirxss_12bpc_mbus_fmts[index];
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_enum_dv_timings: Enumerate all the supported DV timings
> > + * @sd: pointer to v4l2 subdev structure
> > + * @timings: DV timings structure to be returned.
> > + *
> > + * Return: -EINVAL incase of invalid index and pad or zero on success
> > + */
> > +static int xsdirxss_enum_dv_timings(struct v4l2_subdev *sd,
> > + struct v4l2_enum_dv_timings *timings)
> > +{
> > + if (timings->index >= ARRAY_SIZE(fmt_cap))
> > + return -EINVAL;
> > +
> > + if (timings->pad != 0)
> > + return -EINVAL;
> > +
> > + timings->timings = fmt_cap[timings->index];
> > + return 0;
> > +}
> > +
> > +/**
> > + * xsdirxss_query_dv_timings: Query for the current DV timings
> > + * @sd: pointer to v4l2 subdev structure
> > + * @timings: DV timings structure to be returned.
> > + *
> > + * Return: -ENOLCK when video is not locked, -ERANGE when corresponding
> timing
> > + * entry is not found or zero on success.
> > + */
> > +static int xsdirxss_query_dv_timings(struct v4l2_subdev *sd,
> > + struct v4l2_dv_timings *timings)
> > +{
> > + struct xsdirxss_state *state = to_xsdirxssstate(sd);
> > + unsigned int i;
> > +
> > + if (!state->vidlocked)
> > + return -ENOLCK;
> > +
> > + for (i = 0; i < ARRAY_SIZE(xsdirxss_dv_timings); i++) {
> > + if (state->format.width == xsdirxss_dv_timings[i].width &&
> > + state->format.height == xsdirxss_dv_timings[i].height &&
> > + state->frame_interval.denominator ==
> > + (xsdirxss_dv_timings[i].fps * 1000)) {
> > + *timings = xsdirxss_dv_timings[i].format;
> > + return 0;
> > + }
> > + }
> > +
> > + return -ERANGE;
> > +}
> > +
> > +/* -----------------------------------------------------------------------------
> > + * Media Operations
> > + */
> > +
> > +static const struct media_entity_operations xsdirxss_media_ops = {
> > + .link_validate = v4l2_subdev_link_validate
> > +};
> > +
> > +static const struct v4l2_ctrl_ops xsdirxss_ctrl_ops = {
> > + .g_volatile_ctrl = xsdirxss_g_volatile_ctrl,
> > + .s_ctrl = xsdirxss_s_ctrl
> > +};
> > +
> > +static const struct v4l2_ctrl_config xsdirxss_edh_ctrls[] = {
> > + {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_EDH_ERRCNT_ENABLE,
> > + .name = "SDI Rx : EDH Error Count Enable",
> > + .type = V4L2_CTRL_TYPE_BITMASK,
> > + .min = 0,
> > + .max = XSDIRX_EDH_ALLERR_MASK,
> > + .def = 0,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_EDH_ERRCNT,
> > + .name = "SDI Rx : EDH Error Count",
> > + .type = V4L2_CTRL_TYPE_INTEGER,
> > + .min = 0,
> > + .max = 0xFFFF,
> > + .step = 1,
> > + .def = 0,
> > + .flags = V4L2_CTRL_FLAG_VOLATILE |
> V4L2_CTRL_FLAG_READ_ONLY,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_EDH_STATUS,
> > + .name = "SDI Rx : EDH Status",
> > + .type = V4L2_CTRL_TYPE_INTEGER,
> > + .min = 0,
> > + .max = 0xFFFFFFFF,
> > + .step = 1,
> > + .def = 0,
> > + .flags = V4L2_CTRL_FLAG_VOLATILE |
> V4L2_CTRL_FLAG_READ_ONLY,
> > + }
> > +};
> > +
> > +static const struct v4l2_ctrl_config xsdirxss_ctrls[] = {
> > + {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_FRAMER,
> > + .name = "SDI Rx : Enable Framer",
> > + .type = V4L2_CTRL_TYPE_BOOLEAN,
> > + .min = false,
> > + .max = true,
> > + .step = 1,
> > + .def = true,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW,
> > + .name = "SDI Rx : Video Lock Window",
> > + .type = V4L2_CTRL_TYPE_INTEGER,
> > + .min = 0,
> > + .max = 0xFFFFFFFF,
> > + .step = 1,
> > + .def = XSDIRX_DEFAULT_VIDEO_LOCK_WINDOW,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_SEARCH_MODES,
> > + .name = "SDI Rx : Modes search Mask",
> > + .type = V4L2_CTRL_TYPE_BITMASK,
> > + .min = 0,
> > + .max = XSDIRX_DETECT_ALL_MODES,
> > + .def = XSDIRX_DETECT_ALL_MODES,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_MODE_DETECT,
> > + .name = "SDI Rx : Mode Detect Status",
> > + .type = V4L2_CTRL_TYPE_INTEGER,
> > + .min = XSDIRX_MODE_SD_OFFSET,
> > + .max = XSDIRX_MODE_12GF_OFFSET,
> > + .step = 1,
> > + .flags = V4L2_CTRL_FLAG_VOLATILE |
> V4L2_CTRL_FLAG_READ_ONLY,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_CRC,
> > + .name = "SDI Rx : CRC Error status",
> > + .type = V4L2_CTRL_TYPE_INTEGER,
> > + .min = 0,
> > + .max = 0xFFFFFFFF,
> > + .step = 1,
> > + .def = 0,
> > + .flags = V4L2_CTRL_FLAG_VOLATILE |
> V4L2_CTRL_FLAG_READ_ONLY,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED,
> > + .name = "SDI Rx : TS is Interlaced",
> > + .type = V4L2_CTRL_TYPE_BOOLEAN,
> > + .min = false,
> > + .max = true,
> > + .def = false,
> > + .step = 1,
> > + .flags = V4L2_CTRL_FLAG_VOLATILE |
> V4L2_CTRL_FLAG_READ_ONLY,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_ACTIVE_STREAMS,
> > + .name = "SDI Rx : Active Streams",
> > + .type = V4L2_CTRL_TYPE_INTEGER,
> > + .min = 1,
> > + .max = 16,
> > + .def = 1,
> > + .step = 1,
> > + .flags = V4L2_CTRL_FLAG_VOLATILE |
> V4L2_CTRL_FLAG_READ_ONLY,
> > + }, {
> > + .ops = &xsdirxss_ctrl_ops,
> > + .id = V4L2_CID_XILINX_SDIRX_IS_3GB,
> > + .name = "SDI Rx : Is 3GB",
> > + .type = V4L2_CTRL_TYPE_BOOLEAN,
> > + .min = false,
> > + .max = true,
> > + .def = false,
> > + .step = 1,
> > + .flags = V4L2_CTRL_FLAG_VOLATILE |
> V4L2_CTRL_FLAG_READ_ONLY,
> > + }
> > +};
> > +
> > +static const struct v4l2_subdev_core_ops xsdirxss_core_ops = {
> > + .log_status = xsdirxss_log_status,
> > + .subscribe_event = xsdirxss_subscribe_event,
> > + .unsubscribe_event = xsdirxss_unsubscribe_event
> > +};
> > +
> > +static const struct v4l2_subdev_video_ops xsdirxss_video_ops = {
> > + .g_frame_interval = xsdirxss_g_frame_interval,
> > + .s_stream = xsdirxss_s_stream,
> > + .g_input_status = xsdirxss_g_input_status,
> > + .query_dv_timings = xsdirxss_query_dv_timings,
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops xsdirxss_pad_ops = {
> > + .init_cfg = xsdirxss_init_cfg,
> > + .get_fmt = xsdirxss_get_format,
> > + .set_fmt = xsdirxss_set_format,
> > + .enum_mbus_code = xsdirxss_enum_mbus_code,
> > + .enum_dv_timings = xsdirxss_enum_dv_timings,
> > +};
> > +
> > +static const struct v4l2_subdev_ops xsdirxss_ops = {
> > + .core = &xsdirxss_core_ops,
> > + .video = &xsdirxss_video_ops,
> > + .pad = &xsdirxss_pad_ops
> > +};
> > +
> > +/* -----------------------------------------------------------------------------
> > + * Platform Device Driver
> > + */
> > +
> > +static int xsdirxss_parse_of(struct xsdirxss_state *xsdirxss)
> > +{
> > + struct device_node *node = xsdirxss->core.dev->of_node;
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > + struct device *dev = core->dev;
> > + struct fwnode_handle *ep, *rep;
> > + int ret;
> > + const char *sdi_std;
> > +
> > + core->include_edh = of_property_read_bool(node, "xlnx,include-edh");
> > + dev_dbg(dev, "EDH property = %s\n",
> > + core->include_edh ? "Present" : "Absent");
> > +
> > + ret = of_property_read_string(node, "xlnx,line-rate", &sdi_std);
> > + if (ret < 0) {
> > + dev_err(dev, "xlnx,line-rate property not found\n");
> > + return ret;
> > + }
> > +
> > + if (!strncmp(sdi_std, "12G_SDI_8DS", XSDIRX_MAX_STR_LENGTH)) {
>
> Strings in DT are null-terminated, you can use strcmp() and drop
> XSDIRX_MAX_STR_LENGTH.
>
I will remove the strings from DT and have values 0, 1 and 2 to represent 3G, 6G and 12G 8DS mode configurations.
> > + core->mode = XSDIRXSS_SDI_STD_12G_8DS;
> > + } else if (!strncmp(sdi_std, "6G_SDI", XSDIRX_MAX_STR_LENGTH)) {
> > + core->mode = XSDIRXSS_SDI_STD_6G;
> > + } else if (!strncmp(sdi_std, "3G_SDI", XSDIRX_MAX_STR_LENGTH)) {
> > + core->mode = XSDIRXSS_SDI_STD_3G;
> > + } else {
> > + dev_err(dev, "Invalid Line Rate\n");
> > + return -EINVAL;
> > + }
> > + dev_dbg(dev, "SDI Rx Line Rate = %s, mode = %d\n", sdi_std,
> > + core->mode);
> > +
> > + ret = of_property_read_u32(node, "xlnx,bpp", &core->bpc);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get xlnx,bpp\n");
> > + return ret;
> > + }
> > +
> > + if (core->bpc != 10 && core->bpc != 12) {
> > + dev_err(dev, "bits per component=%u. Can be 10 or 12 only\n",
> > + core->bpc);
> > + return -EINVAL;
> > + }
> > +
> > + ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), 0, 0,
> > +
> FWNODE_GRAPH_ENDPOINT_NEXT);
> > + if (!ep) {
> > + dev_err(dev, "no source port found");
> > + ret = -EINVAL;
> > + goto dt_parse_done;
> > + }
> > +
> > + rep = fwnode_graph_get_remote_endpoint(ep);
> > + if (!rep) {
> > + dev_err(dev, "no remote sink endpoint found");
> > + ret = -EINVAL;
> > + }
>
> I don't think you need to check this, the subdev won't be linked
> properly in the pipeline if there's no port anyway.
>
Ok. I thought it was subdev driver's responsibility to validate this too. Hence added.
I will remove this parsing in the next version.
> > +
> > + fwnode_handle_put(rep);
> > +dt_parse_done:
> > + fwnode_handle_put(ep);
> > + return ret;
> > +}
> > +
> > +static int xsdirxss_probe(struct platform_device *pdev)
> > +{
> > + struct v4l2_subdev *subdev;
> > + struct xsdirxss_state *xsdirxss;
> > + struct xsdirxss_core *core;
> > + struct device *dev;
> > + int ret;
> > + unsigned int num_ctrls, num_edh_ctrls = 0, i;
> > +
> > + xsdirxss = devm_kzalloc(&pdev->dev, sizeof(*xsdirxss), GFP_KERNEL);
> > + if (!xsdirxss)
> > + return -ENOMEM;
> > +
> > + xsdirxss->core.dev = &pdev->dev;
> > + core = &xsdirxss->core;
> > + dev = core->dev;
> > +
> > + /* Register interrupt handler */
> > + core->irq = platform_get_irq(pdev, 0);
> > + ret = devm_request_threaded_irq(dev, core->irq, NULL,
> > + xsdirxss_irq_handler, IRQF_ONESHOT,
> > + dev_name(dev), xsdirxss);
>
> Why a threaded IRQ ?
The irq handler calls xsdirxss_set_gtclk() which in turn calls clk_set_rate() and clk_get_rate() which can't be called in the interrupt context.
Hence a threaded irq handler.
>
> > + if (ret) {
> > + dev_err(dev, "Err = %d Interrupt handler reg failed!\n",
> > + ret);
> > + return ret;
> > + }
>
> You should request the IRQ after resetting the core, otherwise
> interrupts could be triggered immediately.
>
Ok I will move this after core disabled below.
> > +
> > + core->num_clks = ARRAY_SIZE(xsdirxss_clks);
> > + core->clks = devm_kcalloc(dev, core->num_clks,
> > + sizeof(*core->clks), GFP_KERNEL);
> > + if (!core->clks)
> > + return -ENOMEM;
> > +
> > + for (i = 0; i < core->num_clks; i++)
> > + core->clks[i].id = xsdirxss_clks[i];
> > +
> > + ret = devm_clk_bulk_get(dev, core->num_clks, core->clks);
> > + if (ret)
> > + return ret;
> > +
> > + ret = clk_bulk_prepare_enable(core->num_clks, core->clks);
> > + if (ret)
> > + return ret;
> > +
> > + ret = xsdirxss_parse_of(xsdirxss);
> > + if (ret < 0)
> > + goto clk_err;
> > +
> > + core->iomem = devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR(core->iomem)) {
> > + ret = PTR_ERR(core->iomem);
> > + goto clk_err;
> > + }
>
> If you move these two calls above handling of the clocks, you will be
> able to return immediately and avoid the goto.
>
Agreed. I will move them above the clock initialization.
> > +
> > + /* Reset the core */
> > + xsdirx_streamflow_control(core, false);
> > + xsdirx_core_disable(core);
> > + xsdirx_clearintr(core, XSDIRX_INTR_ALL_MASK);
> > + xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
> > + xsdirx_enableintr(core, XSDIRX_INTR_ALL_MASK);
> > + xsdirx_globalintr(core, true);
> > + xsdirxss_write(core, XSDIRX_CRC_ERRCNT_REG, 0xFFFF);
> > +
> > + /* Initialize V4L2 subdevice and media entity */
> > + xsdirxss->pad.flags = MEDIA_PAD_FL_SOURCE;
> > +
> > + /* Initialize the default format */
> > + if (core->bpc == 10)
> > + xsdirxss->default_format.code =
> MEDIA_BUS_FMT_UYVY10_1X20;
> > + else
> > + xsdirxss->default_format.code =
> MEDIA_BUS_FMT_UYVY12_1X24;
> > + xsdirxss->default_format.field = V4L2_FIELD_NONE;
> > + xsdirxss->default_format.colorspace = V4L2_COLORSPACE_DEFAULT;
> > + xsdirxss->default_format.width = XSDIRX_DEFAULT_WIDTH;
> > + xsdirxss->default_format.height = XSDIRX_DEFAULT_HEIGHT;
> > +
> > + xsdirxss->format = xsdirxss->default_format;
> > +
> > + /* Initialize V4L2 subdevice and media entity */
> > + subdev = &xsdirxss->subdev;
> > + v4l2_subdev_init(subdev, &xsdirxss_ops);
> > +
> > + subdev->dev = &pdev->dev;
> > + strscpy(subdev->name, dev_name(dev), sizeof(subdev->name));
> > +
> > + subdev->flags |= V4L2_SUBDEV_FL_HAS_EVENTS |
> V4L2_SUBDEV_FL_HAS_DEVNODE;
> > +
> > + subdev->entity.ops = &xsdirxss_media_ops;
> > +
> > + v4l2_set_subdevdata(subdev, xsdirxss);
> > +
> > + ret = media_entity_pads_init(&subdev->entity, 1, &xsdirxss->pad);
> > + if (ret < 0)
> > + goto error;
> > +
> > + /* Initialise and register the controls */
> > + num_ctrls = ARRAY_SIZE(xsdirxss_ctrls);
> > +
> > + if (core->include_edh)
> > + num_edh_ctrls = ARRAY_SIZE(xsdirxss_edh_ctrls);
>
> How about
>
> num_ctrls += ARRAY_SIZE(xsdirxss_edh_ctrls);
>
> > +
> > + v4l2_ctrl_handler_init(&xsdirxss->ctrl_handler,
> > + (num_ctrls + num_edh_ctrls));
>
> num_ctrls);
>
Agree. I will make this change in next version.
> > +
> > + for (i = 0; i < num_ctrls; i++) {
>
> for (i = 0; i < ARRAY_SIZE(xsdirxss_ctrls); i++) {
>
> > + struct v4l2_ctrl *ctrl;
> > +
> > + dev_dbg(dev, "%d %s ctrl = 0x%x\n", i, xsdirxss_ctrls[i].name,
> > + xsdirxss_ctrls[i].id);
> > +
> > + ctrl = v4l2_ctrl_new_custom(&xsdirxss->ctrl_handler,
> > + &xsdirxss_ctrls[i], NULL);
> > + if (!ctrl) {
> > + dev_dbg(dev, "Failed to add %s ctrl\n",
> > + xsdirxss_ctrls[i].name);
> > + goto error;
> > + }
>
> As you check for xsdirxss->ctrl_handler.error below you can drop this
> check and the equivalent one for the EDH controls.
>
Ok I will remove this check here and in EDH controls below.
> > + }
> > +
> > + if (core->include_edh) {
> > + for (i = 0; i < num_edh_ctrls; i++) {
>
> for (i = 0; i < ARRAY_SIZE(xsdirxss_edh_ctrls); i++) {
>
This will be updated in next version.
> > + struct v4l2_ctrl *ctrl;
> > +
> > + dev_dbg(dev, "%d %s ctrl = 0x%x\n", i,
> > + xsdirxss_edh_ctrls[i].name,
> > + xsdirxss_edh_ctrls[i].id);
> > +
> > + ctrl = v4l2_ctrl_new_custom(&xsdirxss->ctrl_handler,
> > + &xsdirxss_edh_ctrls[i],
> > + NULL);
> > + if (!ctrl) {
> > + dev_dbg(dev, "Failed to add %s ctrl\n",
> > + xsdirxss_edh_ctrls[i].name);
> > + goto error;
> > + }
> > + }
> > + }
> > +
> > + if (xsdirxss->ctrl_handler.error) {
> > + dev_err(dev, "failed to add controls\n");
> > + ret = xsdirxss->ctrl_handler.error;
> > + goto error;
> > + }
> > +
> > + subdev->ctrl_handler = &xsdirxss->ctrl_handler;
> > +
> > + ret = v4l2_ctrl_handler_setup(&xsdirxss->ctrl_handler);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to set controls\n");
> > + goto error;
> > + }
> > +
> > + platform_set_drvdata(pdev, xsdirxss);
> > +
> > + ret = v4l2_async_register_subdev(subdev);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to register subdev\n");
> > + goto error;
> > + }
> > +
> > + xsdirxss->streaming = false;
> > +
> > + xsdirx_core_enable(core);
> > +
> > + dev_info(dev, "probe success\n");
>
> You can drop this line, successful driver probing should be silent.
>
Right. I will remove this in next version.
> > +
> > + return 0;
> > +error:
> > + v4l2_ctrl_handler_free(&xsdirxss->ctrl_handler);
> > + media_entity_cleanup(&subdev->entity);
> > + xsdirx_globalintr(core, false);
> > + xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
> > +clk_err:
> > + clk_bulk_disable_unprepare(core->num_clks, core->clks);
> > + return ret;
> > +}
> > +
> > +static int xsdirxss_remove(struct platform_device *pdev)
> > +{
> > + struct xsdirxss_state *xsdirxss = platform_get_drvdata(pdev);
> > + struct xsdirxss_core *core = &xsdirxss->core;
> > + struct v4l2_subdev *subdev = &xsdirxss->subdev;
> > +
> > + v4l2_async_unregister_subdev(subdev);
> > + v4l2_ctrl_handler_free(&xsdirxss->ctrl_handler);
> > + media_entity_cleanup(&subdev->entity);
> > +
> > + xsdirx_globalintr(core, false);
> > + xsdirx_disableintr(core, XSDIRX_INTR_ALL_MASK);
> > + xsdirx_core_disable(core);
> > + xsdirx_streamflow_control(core, false);
> > +
> > + clk_bulk_disable_unprepare(core->num_clks, core->clks);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id xsdirxss_of_id_table[] = {
> > + { .compatible = "xlnx,v-smpte-uhdsdi-rx-ss-2.0" },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, xsdirxss_of_id_table);
> > +
> > +static struct platform_driver xsdirxss_driver = {
> > + .driver = {
> > + .name = "xilinx-sdirxss",
> > + .of_match_table = xsdirxss_of_id_table,
> > + },
> > + .probe = xsdirxss_probe,
> > + .remove = xsdirxss_remove,
> > +};
> > +
> > +module_platform_driver(xsdirxss_driver);
> > +
> > +MODULE_AUTHOR("Vishal Sagar <vsagar@xxxxxxxxxx>");
> > +MODULE_DESCRIPTION("Xilinx SDI Rx Subsystem Driver");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/include/uapi/linux/xilinx-sdirxss.h b/include/uapi/linux/xilinx-
> sdirxss.h
> > new file mode 100644
> > index 000000000000..6f2a093968d9
> > --- /dev/null
> > +++ b/include/uapi/linux/xilinx-sdirxss.h
> > @@ -0,0 +1,179 @@
> > +/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
> > +/*
> > + * Xilinx SDI Rx Subsystem mode, event, custom timings
> > + * and flag definitions.
> > + *
> > + * Copyright (C) 2019 - 2020 Xilinx, Inc.
> > + *
> > + * Contacts: Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> > + */
> > +
> > +#ifndef __UAPI_XILINX_SDIRXSS_H__
> > +#define __UAPI_XILINX_SDIRXSS_H__
> > +
> > +#include <linux/types.h>
> > +#include <linux/v4l2-dv-timings.h>
> > +#include <linux/videodev2.h>
> > +
> > +/*
> > + * Events
> > + *
> > + * V4L2_EVENT_XILINX_SDIRX_UNDERFLOW: Video in to AXI4 Stream core
> underflowed
> > + * V4L2_EVENT_XILINX_SDIRX_OVERFLOW: Video in to AXI4 Stream core
> overflowed
> > + */
> > +#define V4L2_EVENT_XILINX_SDIRX_CLASS
> (V4L2_EVENT_PRIVATE_START | 0x200)
> > +#define V4L2_EVENT_XILINX_SDIRX_UNDERFLOW
> (V4L2_EVENT_XILINX_SDIRX_CLASS | 0x1)
> > +#define V4L2_EVENT_XILINX_SDIRX_OVERFLOW
> (V4L2_EVENT_XILINX_SDIRX_CLASS | 0x2)
> > +
> > +/*
> > + * This enum is used to prepare the bitmask of modes to be detected
> > + */
> > +enum {
> > + XSDIRX_MODE_SD_OFFSET = 0,
> > + XSDIRX_MODE_HD_OFFSET,
> > + XSDIRX_MODE_3G_OFFSET,
> > + XSDIRX_MODE_6G_OFFSET,
> > + XSDIRX_MODE_12GI_OFFSET,
> > + XSDIRX_MODE_12GF_OFFSET,
> > + XSDIRX_MODE_NUM_SUPPORTED,
> > +};
> > +
> > +#define XSDIRX_DETECT_ALL_MODES
> (BIT(XSDIRX_MODE_SD_OFFSET) | \
> > + BIT(XSDIRX_MODE_HD_OFFSET) | \
> > + BIT(XSDIRX_MODE_3G_OFFSET) | \
> > + BIT(XSDIRX_MODE_6G_OFFSET) | \
> > + BIT(XSDIRX_MODE_12GI_OFFSET) | \
> > + BIT(XSDIRX_MODE_12GF_OFFSET))
> > +
> > +/*
> > + * EDH Error Types
> > + * ANC - Ancillary Data Packet Errors
> > + * FF - Full Field Errors
> > + * AP - Active Portion Errors
> > + */
> > +
> > +#define XSDIRX_EDH_ERRCNT_ANC_EDH_ERR BIT(0)
> > +#define XSDIRX_EDH_ERRCNT_ANC_EDA_ERR BIT(1)
> > +#define XSDIRX_EDH_ERRCNT_ANC_IDH_ERR BIT(2)
> > +#define XSDIRX_EDH_ERRCNT_ANC_IDA_ERR BIT(3)
> > +#define XSDIRX_EDH_ERRCNT_ANC_UES_ERR BIT(4)
> > +#define XSDIRX_EDH_ERRCNT_FF_EDH_ERR BIT(5)
> > +#define XSDIRX_EDH_ERRCNT_FF_EDA_ERR BIT(6)
> > +#define XSDIRX_EDH_ERRCNT_FF_IDH_ERR BIT(7)
> > +#define XSDIRX_EDH_ERRCNT_FF_IDA_ERR BIT(8)
> > +#define XSDIRX_EDH_ERRCNT_FF_UES_ERR BIT(9)
> > +#define XSDIRX_EDH_ERRCNT_AP_EDH_ERR BIT(10)
> > +#define XSDIRX_EDH_ERRCNT_AP_EDA_ERR BIT(11)
> > +#define XSDIRX_EDH_ERRCNT_AP_IDH_ERR BIT(12)
> > +#define XSDIRX_EDH_ERRCNT_AP_IDA_ERR BIT(13)
> > +#define XSDIRX_EDH_ERRCNT_AP_UES_ERR BIT(14)
> > +#define XSDIRX_EDH_ERRCNT_PKT_CHKSUM_ERR BIT(15)
> > +
> > +#define XSDIRX_EDH_ALLERR_MASK 0xFFFF
> > +
> > +/* Xilinx DV timings not in mainline yet */
> > +#define XLNX_V4L2_DV_BT_2048X1080P24 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 74250000, 510, 44, 148, 4, 5, 36, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080P25 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 74250000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080P30 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 74250000, 66, 20, 66, 4, 5, 36, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080I48 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 74250000, 329, 44, 329, 2, 5, 15, 3, 5, 15, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080I50 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 74250000, 274, 44, 274, 2, 5, 15, 3, 5, 15, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080I60 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 1, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 74250000, 66, 20, 66, 2, 5, 15, 3, 5, 15, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_1920X1080P48 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(1920, 1080, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 148500000, 638, 44, 148, 4, 5, 36, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080P48 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 148500000, 510, 44, 148, 4, 5, 36, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080P50 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 148500000, 400, 44, 148, 4, 5, 36, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_2048X1080P60 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(2048, 1080, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 148500000, 88, 44, 20, 4, 5, 36, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_3840X2160P48 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(3840, 2160, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 594000000, 1276, 88, 296, 8, 10, 72, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_4096X2160P48 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(4096, 2160, 0, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 594000000, 1020, 88, 296, 8, 10, 72, 0, 0, 0, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#define XLNX_V4L2_DV_BT_1920X1080I48 { \
> > + .type = V4L2_DV_BT_656_1120, \
> > + V4L2_INIT_BT_TIMINGS(1920, 1080, 1, \
> > + V4L2_DV_HSYNC_POS_POL | V4L2_DV_VSYNC_POS_POL, \
> > + 148500000, 371, 88, 371, 2, 5, 15, 3, 5, 15, \
> > + V4L2_DV_BT_STD_SDI) \
> > +}
> > +
> > +#endif /* __UAPI_XILINX_SDIRXSS_H__ */
> > diff --git a/include/uapi/linux/xilinx-v4l2-controls.h
> b/include/uapi/linux/xilinx-v4l2-controls.h
> > index b6441fe705c5..e9de65e82642 100644
> > --- a/include/uapi/linux/xilinx-v4l2-controls.h
> > +++ b/include/uapi/linux/xilinx-v4l2-controls.h
> > @@ -71,4 +71,71 @@
> > /* Noise level */
> > #define V4L2_CID_XILINX_TPG_NOISE_GAIN
> (V4L2_CID_XILINX_TPG + 17)
> >
> > +/*
> > + * Xilinx SDI Rx Subsystem
> > + */
> > +
> > +/* The base for the sdi rx driver controls.
> > + * We reserve 32 controls for this driver.
> > + *
> > + * The V4L2_CID_XILINX_SDIRX_EDH_* controls are present only if
> > + * EDH is enabled.
> > + * The controls which can be set should only be set before enabling
> > + * streaming. The controls which can be got should be called while
> > + * streaming to get correct values.
> > + * The V4L2_CID_XILINX_SDIRX_MODE_DETECT can be called when query
> dv timing
> > + * returns a valid timing.
> > + */
> > +
> > +#define V4L2_CID_XILINX_SDIRX
> (V4L2_CID_XILINX_BASE + 0x20)
> > +
> > +/* Framer Control to enable or disable the framer */
> > +#define V4L2_CID_XILINX_SDIRX_FRAMER
> (V4L2_CID_XILINX_SDIRX + 1)
>
> This control needs more documentation. What does it do, and how should
> it be used ?
This is documented in the Table 2-2 rx_frame_en row of PG 205
https://www.xilinx.com/support/documentation/ip_documentation/v_smpte_uhdsdi/v1_0/pg205-v-smpte-uhdsdi.pdf
"This input enables the SDI framer function. When this input is High, the framer automatically readjusts the output word
alignment to match the alignment of each timing reference signal (TRS). TRS is a generic term referring to both EAV and SAV sequences.
Normally, this input should be always be High. But, the user application may control this input to implement TRS filtering
to prevent a signal misaligned TRS from causing erroneous alignment changes."
E/SAV is End/Start of Active Video.
I will update this in next version
>
> > +/*
> > + * Video Lock Window Control to set the video lock window value
> > + * This is the amount of time the mode and transport stream need
> > + * to be locked before a video lock interrupt occurs.
> > + */
> > +#define V4L2_CID_XILINX_SDIRX_VIDLOCK_WINDOW
> (V4L2_CID_XILINX_SDIRX + 2)
> > +/* EDH Error Mask Control to enable EDH error count */
> > +#define V4L2_CID_XILINX_SDIRX_EDH_ERRCNT_ENABLE
> (V4L2_CID_XILINX_SDIRX + 3)
> > +/*
> > + * Mode search Control to pass the bit mask of modes to detect.
> > + *
> > + * bit 0 set to detect SD mode,
> > + * bit 1 set to detect HD mode,
> > + * bit 2 set to detect 3G (3GA & 3GB) mode,
> > + * bit 3 set to detect 6G mode,
> > + * bit 4 set to detect 12G integer frame rate mode,
> > + * bit 5 set to detect 12G fractional frame rate mode,
> > + */
> > +#define V4L2_CID_XILINX_SDIRX_SEARCH_MODES
> (V4L2_CID_XILINX_SDIRX + 4)
> > +/*
> > + * Get Detected Mode control
> > + *
> > + * Control Value - Mode detected
> > + * 0 - SD
> > + * 1 - HD
> > + * 2 - 3G (3GA & 3GB)
> > + * 3 - 6G
> > + * 4 - 12G integer frame rate
> > + * 5 - 12G fractional frame rate
> > + */
> > +#define V4L2_CID_XILINX_SDIRX_MODE_DETECT
> (V4L2_CID_XILINX_SDIRX + 5)
> > +/* Get number of CRC errors status control */
> > +#define V4L2_CID_XILINX_SDIRX_CRC
> (V4L2_CID_XILINX_SDIRX + 6)
> > +/* Get EDH error count control */
> > +#define V4L2_CID_XILINX_SDIRX_EDH_ERRCNT
> (V4L2_CID_XILINX_SDIRX + 7)
> > +/* Get EDH status control */
> > +#define V4L2_CID_XILINX_SDIRX_EDH_STATUS
> (V4L2_CID_XILINX_SDIRX + 8)
> > +/* Get Transport Interlaced status whether it is interlaced or not */
> > +#define V4L2_CID_XILINX_SDIRX_TS_IS_INTERLACED
> (V4L2_CID_XILINX_SDIRX + 9)
> > +/* Get number of Active Streams */
> > +#define V4L2_CID_XILINX_SDIRX_ACTIVE_STREAMS
> (V4L2_CID_XILINX_SDIRX + 10)
> > +/*
> > + * Get if the detected mode is 3GB.
> > + * Can be used to distinguished between 3GA and 3GB
> > + */
> > +#define V4L2_CID_XILINX_SDIRX_IS_3GB
> (V4L2_CID_XILINX_SDIRX + 11)
> > +
> > #endif /* __UAPI_XILINX_V4L2_CONTROLS_H__ */
>
> --
> Regards,
>
> Laurent Pinchart
Regards
Vishal Sagar
