Hi Benjamin,
got it, thanks a lot.
best regards
Dillon
On Fri, May 15, 2020 at 5:34 PM Benjamin GAIGNARD
<benjamin.gaignard@xxxxxx> wrote:
>
>
>
> On 5/15/20 11:24 AM, dillon min wrote:
> > Hi Benjamin,
> >
> > thanks for reply.
> >
> > On Fri, May 15, 2020 at 4:31 PM Benjamin GAIGNARD
> > <benjamin.gaignard@xxxxxx> wrote:
> >>
> >>
> >> On 5/14/20 3:07 PM, dillon min wrote:
> >>> Hi Alexandre,
> >>>
> >>> On Thu, May 14, 2020 at 8:53 PM Alexandre Torgue
> >>> <alexandre.torgue@xxxxxx> wrote:
> >>>>
> >>>> On 5/14/20 10:24 AM, Linus Walleij wrote:
> >>>>> On Tue, May 12, 2020 at 9:04 AM <dillon.minfei@xxxxxxxxx> wrote:
> >>>>>
> >>>>>> From: dillon min <dillon.minfei@xxxxxxxxx>
> >>>>>>
> >>>>>> Enable the ltdc & ili9341 on stm32429-disco board.
> >>>>>>
> >>>>>> Signed-off-by: dillon min <dillon.minfei@xxxxxxxxx>
> >>>>> This mostly looks good but...
> >>>>>
> >>>>>> +&spi5 {
> >>>>>> + status = "okay";
> >>>>>> + pinctrl-0 = <&spi5_pins>;
> >>>>>> + pinctrl-names = "default";
> >>>>>> + #address-cells = <1>;
> >>>>>> + #size-cells = <0>;
> >>>>>> + cs-gpios = <&gpioc 2 GPIO_ACTIVE_LOW>;
> >>>>>> + dmas = <&dma2 3 2 0x400 0x0>,
> >>>>>> + <&dma2 4 2 0x400 0x0>;
> >>>>>> + dma-names = "rx", "tx";
> >>>>> These DMA assignments seem to be SoC things and should
> >>>>> rather be in the DTS(I) file where &spi5 is defined, right?
> >>>>> stm32f429.dtsi I suppose?
> >>>> I agree with Linus, DMA have to be defined in SoC dtsi. And if a board
> >>>> doesn't want to use it, we use the "delete-property".
> >>> Yes, will move to Soc dtsi in next submits.
> >>>
> >>> i'm working on write a v4l2-m2m driver for dma2d of stm32 to support
> >>> pixel conversion
> >>> alpha blending between foreground and background graphics.
> >>>
> >>> as you know, some soc's engineer trying to add this function to drm system.
> >>>
> >>> do you know st's planning about soc's hardware accelerator driver on stm32mp?
> >>> such as chrom-art, will add to drm subsystem via ioctl to access, or to v4l2,
> >> On stm32mp we do not plan to use chrom-art in drm or v4l2 because it
> >> does fit
> >> with userland way of working. We use the GPU to do conversion, scaling,
> >> blending
> >> and composition in only one go.
> >> As explain here [1] DRM subsytem it isn't a solution and v4l2-m2m isn't
> >> used in any
> >> mainline compositors like Weston or android surfaceflinger.
> >>
> >> Benjamin
> >>
> > After check stm32mp's datasheets, they don't have chrom-art ip inside. sorry for
> > didn't check it yet.
> >
> > for stm32h7 series with chrom-art, jpeg hardware accelerator inside.
> > does st has plan to
> > setup a driver to support it ? i prefer v4l2-m2m should be easier to
> > implement it.
> > co work with dcmi, fbdev.
> ST doesn't plan to create a driver for chrom-art because nothing in
> mainline
> userland could use it.
>
> Benjamin
> >
> > thanks.
> >
> > best regards.
> >
> > Dillon
> >> [1]
> >> https://www.phoronix.com/scan.php?page=news_item&px=Linux-DRM-No-2D-Accel-API
> >>> thanks.
> >>>
> >>>>> It is likely the same no matter which device is using spi5.
> >>>>>
> >>>>> Yours,
> >>>>> Linus Walleij
> >>>>>
> >>> _______________________________________________
> >>> Linux-stm32 mailing list
> >>> Linux-stm32@xxxxxxxxxxxxxxxxxxxxxxxxxxxx
> >>> https://st-md-mailman.stormreply.com/mailman/listinfo/linux-stm32
