Hi Oleksij,
thanks for your patche. In general you should use generic node names,
sort the properties, nodes, phandles correctly except the iomux node.
Finally, pls don't mix dts and dtsi files. If the dts needs the iomux
than pls mux it within the dts file :) Pls see my comments below.
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2014 Protonic Holland
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-prti6q.dtsi"
> +
> +/ {
> + model = "Protonic PRTI6Q board";
> + compatible = "prt,prti6q", "fsl,imx6q";
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0xf0000000>;
> + };
> +
> + sound-spdif {
> + compatible = "fsl,imx-audio-spdif";
> + model = "imx-spdif";
> + spdif-controller = <&spdif>;
> + spdif-in;
> + spdif-out;
> + };
> +
> + clocks {
Is this container necessary?
> + spi3_crystal: spi3clk {
Should we name the clock extcanclk?
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <25000000>;
> + };
> + };
> +
> + panel {
> + compatible = "kyo,tcg121xglp";
> + backlight = <&backlight_lcd>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +
> + reg_wl12xx: regulator-wl12xx {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wl1271_npd>;
Does npd mean no-power-down?
> + compatible = "regulator-fixed";
The "compatible" property should be the 1st property.
> + regulator-name = "regulator-WL12xx";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&gpio1 26 0>;
> + startup-delay-us = <70000>;
> + enable-active-high;
> + };
Please sort all nodes and phandles alphabetical, this applies to all
your .dts(i) files except the iomux node. I saw some dt files moving
that node to the end. @Shawn is this a unwritten rule?
> +};
> +
> +&ecspi2 {
> + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + status = "okay";
> +
> + can3: mcp2515@0 {
Where is this phandle used? Please name the node more generic e.g. like
the phandle and drop the phandle if not used.
> + compatible = "microchip,mcp2515";
> + spi-max-frequency = <5000000>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
> + reg = <0>;
The "reg" property should be listed after the "compatible" property.
> + clocks = <&spi3_crystal>;
> + };
> +
> + adc128: adc128@1 {
> + compatible = "ti,adc128s052";
> + reg = <1>;
> + vref-supply = <®_3v3>;
> + spi-max-frequency = <2000000>;
> + };
> +};
> +
> +&iomuxc {
> + prti6q {
Is this container necessary?
> + pinctrl_nand: nandgrp {
Where is this node used?
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
Here we are mixing dtsi and dts files and the dtsi is not self-contained
anymore. This isn't a good idea.
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
> + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> + /* power enable, high active */
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
> + >;
> + };
> +
> + pinctrl_hdmi: hdmigrp {
> + fsl,pins = <
> + /* NOTE: DDC is done via I2C2, so DON'T
> + * configure DDC pins for HDMI!
> + */
> + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> + >;
> + };
> +
> + pinctrl_spdif: spdifgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
> + MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_leds: ledsgrp {
Here we are mixing it too.
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
> + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
> + >;
> + };
> +
> + /* DDC */
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
Most of the node is already defined in your dtsi file and again
mixing dtsi and dts file. Pls check that for all your files. I
would mux the common things like miso,mosi,clk within the dtsi and the
cs signals here. Also we can use the phandle to extend the node.
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + /* CAN3 CS */
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + /* ADC128S022 CS */
> + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
> + /* CAN3_nINT */
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> + >;
> + };
> +
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> +
> + /* Phy reset */
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
Why is this node needed? We only add the IRQ line. You only need to use
the phandle to extend the node or add a new wl1271grp. I would prefer
the 2nd.
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> + /* WL12xx IRQ */
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> + >;
> + };
> +
> + pinctrl_wl1271_npd: wl1271_npd {
Pls don't use '_' within node names.
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> + >;
> + };
> + };
> +};
> +
> +&hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmi>;
> + ddc-i2c-bus = <&i2c2>;
> + status = "okay";
> +};
> +
> +&spdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spdif>;
> + status = "okay";
> +};
> +
> +/* DDC */
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&sata {
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii-id";
> + phy-handle = <&rgmii_phy>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microchip KSZ9031RNX PHY */
> + rgmii_phy: ethernet-phy@0 {
> + reg = <0>;
> + interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
> + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <10000>;
> + reset-deassert-us = <300>;
> + };
> + };
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel@0 {
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + vmmc-supply = <®_wl12xx>;
> + non-removable;
> + cap-power-off-card;
> + keep-power-in-suspend;
> + status = "okay";
> +
> + wl1271 {
> + compatible = "ti,wl1271";
> + irq-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> + ref-clock-frequency = "38400000";
> + tcxo-clock-frequency = "19200000";
> + };
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
> new file mode 100644
> index 000000000000..6515b96fa0a5
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
Should we add the .dtsi file seperate?
> @@ -0,0 +1,489 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright (c) 2014 Protonic Holland
> + */
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> + chosen {
> + stdout-path = &uart4;
> + };
> +
> + reg_3v3: regulator-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_1v8: regulator-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_1v2: regulator-1v2 {
> + compatible = "regulator-fixed";
> + regulator-name = "1v2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: regulator-otg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "otg-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 22 0>;
> + enable-active-high;
> + };
> +
> + reg_usb_h1_vbus: regulator-h1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "h1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "prti6q-sgtl5000";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Line", "Line In Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "External Speaker";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "External Speaker", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&ssi1>;
> + system-clock-frequency = <0>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&codec>;
> + bitclock-master;
> + frame-master;
> + };
> + };
> +
> + backlight_lcd: backlight-lcd {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight>;
> + compatible = "pwm-backlight";
Should be the first property.
> + pwms = <&pwm1 0 5000000>;
> + brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192
> + 255>;
> + default-brightness-level = <15>;
Can you check the num-interpolated-steps property?
> + power-supply = <®_3v3>;
> + status = "okay";
Should be the last property.
> + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + };
> +
> + leds: led-controller {
led-controller?
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_leds>;
> +
> + led-hb0 {
Do we need the led- prefix here?
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led-mmc0 {
> + function = LED_FUNCTION_SD;
> + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "disk-activity";
> + };
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +
> + mux_ssi1 {
> + fsl,audmux-port = <0>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN 0
> + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> + IMX_AUDMUX_V2_PTCR_TFSDIR 0
> + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> + >;
> + };
> +
> + mux_pins3 {
> + fsl,audmux-port = <2>;
> + fsl,port-config = <
> + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> + 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> + >;
> + };
> +};
> +
> +&ecspi1 {
> + cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
Nitpick, it is uncommon to list cs-gpios first.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + status = "okay";
> +
> + flash: s25sl032p@0 {
Please use a generic name like spi-flash or flash.
> + compatible = "spansion,m25p80";
> + spi-max-frequency = <20000000>;
> + reg = <0>;
After the compatible string.
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "boot";
> + reg = <0x0 0x80000>;
> + };
> +
> + partition@80000 {
> + label = "env";
> + reg = <0x80000 0x10000>;
> + };
> +
> + partition@90000 {
> + label = "spare";
> + reg = <0x90000 0x370000>;
> + };
The partitions should be listed under the partitions node.
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + codec: sgtl5000@a {
Pls use generic names for all nodes, pls check that for all your dts(i)
files.
> + #sound-dai-cells = <0>;
> + compatible = "fsl,sgtl5000";
> + reg = <0xa>;
Compatible and reg should be moved to the begin.
> + clocks = <&clks 201>;
> + VDDA-supply = <®_3v3>;
> + VDDIO-supply = <®_3v3>;
> + VDDD-supply = <®_1v8>;
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + can_adc: ads1015@49 {
Do we need the phandle here? Also node name is not generic and the
phandle is a bit odd can_adc listed under an i2c-node?
> + compatible = "ti,ads1015";
> + reg = <0x49>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@4 {
> + reg = <4>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + channel@5 {
> + reg = <5>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + channel@6 {
> + reg = <6>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> +
> + channel@7 {
> + reg = <7>;
> + ti,gain = <3>;
> + ti,datarate = <3>;
> + };
> + };
> +
> + tmp103: tmp103@70 {
> + compatible = "ti,tmp103";
> + reg = <0x70>;
> + };
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + prti6q {
Is this container needed.
> + pinctrl_hog: hoggrp {
Pls, don't use hoggrps..
> + fsl,pins = <
> + /* SGTL5000 sys_mclk */
> + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x100b0
> + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x100b0
> + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0
> + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0
> + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0
> + >;
> + };
> +
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> + /* CS */
> + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + /* CS */
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + /* CAN3_nINT */
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
> + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart5: uart5grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> + MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
> + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
> + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
> + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
> + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> + >;
> + };
> +
> + pinctrl_can1: can1grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
> + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
> + >;
> + };
> +
> + pinctrl_can2: can2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
> + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
> + >;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> + >;
> + };
> +
> + pinctrl_backlight: backlightgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ipu1_csi0: ipu1csi0grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> + >;
> + };
> + };
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "okay";
> +};
> +
> +&ssi1 {
> + #sound-dai-cells = <0>;
> + fsl,mode = "i2s-slave";
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&uart5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart5>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_h1_vbus>;
> + phy_type = "utmi";
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + phy_type = "utmi";
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #size-cells = <1>;
> + #address-cells = <1>;
> +
> + bootstate_backend: bootstate_backend@f0000 {
> + reg = <0xf0000 0x10000>;
> + label = "bootstate";
> + };
> + };
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can1>;
> + status = "okay";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can2>;
> + status = "okay";
> +};
Regards,
Marco
