On Thu, Mar 19, 2020 at 11:21:09AM +0100, Marco Felsch wrote:
> Hi Oleksij,
>
> thanks for your patche. In general you should use generic node names,
> sort the properties, nodes, phandles correctly except the iomux node.
> Finally, pls don't mix dts and dtsi files. If the dts needs the iomux
> than pls mux it within the dts file :) Pls see my comments below.
>
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright (c) 2014 Protonic Holland
> > + */
> > +
> > +/dts-v1/;
> > +#include "imx6q.dtsi"
> > +#include "imx6qdl-prti6q.dtsi"
> > +
> > +/ {
> > + model = "Protonic PRTI6Q board";
> > + compatible = "prt,prti6q", "fsl,imx6q";
> > +
> > + memory@10000000 {
> > + device_type = "memory";
> > + reg = <0x10000000 0xf0000000>;
> > + };
> > +
> > + sound-spdif {
> > + compatible = "fsl,imx-audio-spdif";
> > + model = "imx-spdif";
> > + spdif-controller = <&spdif>;
> > + spdif-in;
> > + spdif-out;
> > + };
> > +
> > + clocks {
>
> Is this container necessary?
removed.
> > + spi3_crystal: spi3clk {
>
> Should we name the clock extcanclk?
i synced it with schematics name
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <25000000>;
> > + };
> > + };
> > +
> > + panel {
> > + compatible = "kyo,tcg121xglp";
> > + backlight = <&backlight_lcd>;
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&lvds0_out>;
> > + };
> > + };
> > + };
> > +
> > + reg_wl12xx: regulator-wl12xx {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wl1271_npd>;
>
> Does npd mean no-power-down?
ACK
>
> > + compatible = "regulator-fixed";
>
> The "compatible" property should be the 1st property.
done
> > + regulator-name = "regulator-WL12xx";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + gpio = <&gpio1 26 0>;
> > + startup-delay-us = <70000>;
> > + enable-active-high;
> > + };
>
> Please sort all nodes and phandles alphabetical, this applies to all
> your .dts(i) files except the iomux node. I saw some dt files moving
> that node to the end. @Shawn is this a unwritten rule?
done
>
> > +};
> > +
> > +&ecspi2 {
> > + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi2>;
> > + status = "okay";
> > +
> > + can3: mcp2515@0 {
>
> Where is this phandle used? Please name the node more generic e.g. like
> the phandle and drop the phandle if not used.
done
> > + compatible = "microchip,mcp2515";
> > + spi-max-frequency = <5000000>;
> > + interrupt-parent = <&gpio3>;
> > + interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
> > + reg = <0>;
>
> The "reg" property should be listed after the "compatible" property.
done
> > + clocks = <&spi3_crystal>;
> > + };
> > +
> > + adc128: adc128@1 {
> > + compatible = "ti,adc128s052";
> > + reg = <1>;
> > + vref-supply = <®_3v3>;
> > + spi-max-frequency = <2000000>;
> > + };
> > +};
> > +
> > +&iomuxc {
> > + prti6q {
>
> Is this container necessary?
removed
> > + pinctrl_nand: nandgrp {
>
> Where is this node used?
removed and other nodes are reworked as well
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> > + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> > + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> > + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> > + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> > + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
> > + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> > + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> > + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> > + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> > + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> > + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> > + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> > + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> > + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> > + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> > + >;
> > + };
> > +
> > + pinctrl_usbotg: usbotggrp {
>
> Here we are mixing dtsi and dts files and the dtsi is not self-contained
> anymore. This isn't a good idea.
done
>
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
> > + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> > + /* power enable, high active */
> > + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
> > + >;
> > + };
> > +
> > + pinctrl_hdmi: hdmigrp {
> > + fsl,pins = <
> > + /* NOTE: DDC is done via I2C2, so DON'T
> > + * configure DDC pins for HDMI!
> > + */
> > + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> > + >;
> > + };
> > +
> > + pinctrl_spdif: spdifgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
> > + MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_leds: ledsgrp {
>
> Here we are mixing it too.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
> > + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
> > + >;
> > + };
> > +
> > + /* DDC */
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi2: ecspi2grp {
>
> Most of the node is already defined in your dtsi file and again
> mixing dtsi and dts file. Pls check that for all your files. I
> would mux the common things like miso,mosi,clk within the dtsi and the
> cs signals here. Also we can use the phandle to extend the node.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> > + /* CAN3 CS */
> > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> > + /* ADC128S022 CS */
> > + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
> > + /* CAN3_nINT */
> > + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> > +
> > + /* Phy reset */
> > + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> > + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
>
> Why is this node needed? We only add the IRQ line. You only need to use
> the phandle to extend the node or add a new wl1271grp. I would prefer
> the 2nd.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> > + /* WL12xx IRQ */
> > + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> > + >;
> > + };
> > +
> > + pinctrl_wl1271_npd: wl1271_npd {
>
> Pls don't use '_' within node names.
done
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> > + >;
> > + };
> > + };
> > +};
> > +
> > +&hdmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hdmi>;
> > + ddc-i2c-bus = <&i2c2>;
> > + status = "okay";
> > +};
> > +
> > +&spdif {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_spdif>;
> > + status = "okay";
> > +};
> > +
> > +/* DDC */
> > +&i2c2 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +};
> > +
> > +&sata {
> > + status = "okay";
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii-id";
> > + phy-handle = <&rgmii_phy>;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + /* Microchip KSZ9031RNX PHY */
> > + rgmii_phy: ethernet-phy@0 {
> > + reg = <0>;
> > + interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
> > + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> > + reset-assert-us = <10000>;
> > + reset-deassert-us = <300>;
> > + };
> > + };
> > +};
> > +
> > +&ldb {
> > + status = "okay";
> > +
> > + lvds-channel@0 {
> > + status = "okay";
> > +
> > + port@4 {
> > + reg = <4>;
> > +
> > + lvds0_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + vmmc-supply = <®_wl12xx>;
> > + non-removable;
> > + cap-power-off-card;
> > + keep-power-in-suspend;
> > + status = "okay";
> > +
> > + wl1271 {
> > + compatible = "ti,wl1271";
> > + irq-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> > + ref-clock-frequency = "38400000";
> > + tcxo-clock-frequency = "19200000";
> > + };
> > +};
> > +
> > +&snvs_poweroff {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
> > new file mode 100644
> > index 000000000000..6515b96fa0a5
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
>
> Should we add the .dtsi file seperate?
better no. it is useless as standalone file any way.
> > @@ -0,0 +1,489 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright (c) 2014 Protonic Holland
> > + */
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/sound/fsl-imx-audmux.h>
> > +
> > +/ {
> > + chosen {
> > + stdout-path = &uart4;
> > + };
> > +
> > + reg_3v3: regulator-3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_1v8: regulator-1v8 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "1v8";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_1v2: regulator-1v2 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "1v2";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usb_otg_vbus: regulator-otg-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "otg-vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio3 22 0>;
> > + enable-active-high;
> > + };
> > +
> > + reg_usb_h1_vbus: regulator-h1-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "h1-vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +
> > + sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,name = "prti6q-sgtl5000";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,widgets =
> > + "Microphone", "Microphone Jack",
> > + "Line", "Line In Jack",
> > + "Headphone", "Headphone Jack",
> > + "Speaker", "External Speaker";
> > + simple-audio-card,routing =
> > + "MIC_IN", "Microphone Jack",
> > + "LINE_IN", "Line In Jack",
> > + "Headphone Jack", "HP_OUT",
> > + "External Speaker", "LINE_OUT";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&ssi1>;
> > + system-clock-frequency = <0>;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&codec>;
> > + bitclock-master;
> > + frame-master;
> > + };
> > + };
> > +
> > + backlight_lcd: backlight-lcd {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_backlight>;
> > + compatible = "pwm-backlight";
>
> Should be the first property.
done
> > + pwms = <&pwm1 0 5000000>;
> > + brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192
> > + 255>;
> > + default-brightness-level = <15>;
>
> Can you check the num-interpolated-steps property?
done
> > + power-supply = <®_3v3>;
> > + status = "okay";
>
> Should be the last property.
done
> > + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + leds: led-controller {
>
> led-controller?
renamed to leds
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_leds>;
> > +
> > + led-hb0 {
>
> Do we need the led- prefix here?
if i interpret it properly, then yes:
Documentation/devicetree/bindings/leds/leds-gpio.yaml
> > + function = LED_FUNCTION_STATUS;
> > + gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > +
> > + led-mmc0 {
> > + function = LED_FUNCTION_SD;
> > + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "disk-activity";
> > + };
> > + };
> > +};
> > +
> > +&audmux {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_audmux>;
> > + status = "okay";
> > +
> > + mux_ssi1 {
> > + fsl,audmux-port = <0>;
> > + fsl,port-config = <
> > + IMX_AUDMUX_V2_PTCR_SYN 0
> > + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> > + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> > + IMX_AUDMUX_V2_PTCR_TFSDIR 0
> > + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> > + >;
> > + };
> > +
> > + mux_pins3 {
> > + fsl,audmux-port = <2>;
> > + fsl,port-config = <
> > + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> > + 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> > + >;
> > + };
> > +};
> > +
> > +&ecspi1 {
> > + cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
>
> Nitpick, it is uncommon to list cs-gpios first.
git grep -B1 "cs-gpios" arch/arm/boot/dts/
shows, it is common.
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1>;
> > + status = "okay";
> > +
> > + flash: s25sl032p@0 {
>
> Please use a generic name like spi-flash or flash.
done
> > + compatible = "spansion,m25p80";
> > + spi-max-frequency = <20000000>;
> > + reg = <0>;
>
> After the compatible string.
done
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition@0 {
> > + label = "boot";
> > + reg = <0x0 0x80000>;
> > + };
> > +
> > + partition@80000 {
> > + label = "env";
> > + reg = <0x80000 0x10000>;
> > + };
> > +
> > + partition@90000 {
> > + label = "spare";
> > + reg = <0x90000 0x370000>;
> > + };
>
> The partitions should be listed under the partitions node.
done
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + codec: sgtl5000@a {
>
> Pls use generic names for all nodes, pls check that for all your dts(i)
> files.
done
> > + #sound-dai-cells = <0>;
> > + compatible = "fsl,sgtl5000";
> > + reg = <0xa>;
>
> Compatible and reg should be moved to the begin.
done
> > + clocks = <&clks 201>;
> > + VDDA-supply = <®_3v3>;
> > + VDDIO-supply = <®_3v3>;
> > + VDDD-supply = <®_1v8>;
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + can_adc: ads1015@49 {
>
> Do we need the phandle here? Also node name is not generic and the
> phandle is a bit odd can_adc listed under an i2c-node?
removed and renamed
> > + compatible = "ti,ads1015";
> > + reg = <0x49>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + channel@4 {
> > + reg = <4>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > +
> > + channel@5 {
> > + reg = <5>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > +
> > + channel@6 {
> > + reg = <6>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > +
> > + channel@7 {
> > + reg = <7>;
> > + ti,gain = <3>;
> > + ti,datarate = <3>;
> > + };
> > + };
> > +
> > + tmp103: tmp103@70 {
> > + compatible = "ti,tmp103";
> > + reg = <0x70>;
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + prti6q {
>
> Is this container needed.
removed
> > + pinctrl_hog: hoggrp {
>
> Pls, don't use hoggrps..
removed
> > + fsl,pins = <
> > + /* SGTL5000 sys_mclk */
> > + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> > + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x100b0
> > + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x100b0
> > + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0
> > + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0
> > + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_audmux: audmuxgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> > + >;
> > + };
> > +
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> > + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> > + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> > + /* CS */
> > + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi2: ecspi2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> > + /* CS */
> > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> > + /* CAN3_nINT */
> > + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
> > + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> > + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_uart2: uart2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
> > + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
> > + MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart4: uart4grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart5: uart5grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> > + MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
> > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
> > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
> > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
> > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
> > + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
> > + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
> > + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
> > + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> > + >;
> > + };
> > +
> > + pinctrl_can1: can1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
> > + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
> > + >;
> > + };
> > +
> > + pinctrl_can2: can2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
> > + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
> > + >;
> > + };
> > +
> > + pinctrl_pwm1: pwm1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_backlight: backlightgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_ipu1_csi0: ipu1csi0grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> > + >;
> > + };
> > + };
> > +};
> > +
> > +&pcie {
> > + status = "okay";
> > +};
> > +
> > +&pwm1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm1>;
> > + status = "okay";
> > +};
> > +
> > +&ssi1 {
> > + #sound-dai-cells = <0>;
> > + fsl,mode = "i2s-slave";
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + status = "okay";
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart4>;
> > + status = "okay";
> > +};
> > +
> > +&uart5 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart5>;
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + vbus-supply = <®_usb_h1_vbus>;
> > + phy_type = "utmi";
> > + dr_mode = "host";
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + vbus-supply = <®_usb_otg_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg>;
> > + phy_type = "utmi";
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + bus-width = <8>;
> > + non-removable;
> > + status = "okay";
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #size-cells = <1>;
> > + #address-cells = <1>;
> > +
> > + bootstate_backend: bootstate_backend@f0000 {
> > + reg = <0xf0000 0x10000>;
> > + label = "bootstate";
> > + };
> > + };
> > +};
> > +
> > +&can1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_can1>;
> > + status = "okay";
> > +};
> > +
> > +&can2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_can2>;
> > + status = "okay";
> > +};
>
> Regards,
> Marco
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Attachment:
signature.asc
Description: PGP signature
