Hi Marek,Le ven., mars 13, 2020 at 09:03, Marek Szyprowski <m.szyprowski@xxxxxxxxxxx> a écrit :
On 12.03.2020 16:34, Paul Cercueil wrote:From: Stenkin Evgeniy <stenkinevgeniy@xxxxxxxxx>Add devicetree file for the Exynos 4210 based Galaxy S2 (i9100 version).Signed-off-by: Stenkin Evgeniy <stenkinevgeniy@xxxxxxxxx> Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx> --- arch/arm/boot/dts/Makefile | 1 +arch/arm/boot/dts/exynos4210-i9100.dts | 816 +++++++++++++++++++++++++2 files changed, 817 insertions(+) create mode 100644 arch/arm/boot/dts/exynos4210-i9100.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index d6546d2676b9..522436d30690 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -181,6 +181,7 @@ dtb-$(CONFIG_ARCH_EXYNOS3) += \ exynos3250-monk.dtb \ exynos3250-rinato.dtb dtb-$(CONFIG_ARCH_EXYNOS4) += \ + exynos4210-i9100.dtb \ exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-trats.dtb \diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dtsnew file mode 100644 index 000000000000..c218e34959be --- /dev/null +++ b/arch/arm/boot/dts/exynos4210-i9100.dts @@ -0,0 +1,816 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Exynos4210 based Galaxy S2 (i9100 version) device tree + * + * Copyright (c) 2012 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * Copyright (c) 2020 Stenkin Evgeniy <stenkinevgeniy@xxxxxxxxx> + * Copyright (c) 2020 Paul Cercueil <paul@xxxxxxxxxxxxxxx> + *+ * Device tree source file for Samsung's Galaxy S2 smartphone (i9100 version),+ * which is based on Samsung's Exynos4210 SoC. + */ + +/dts-v1/; +#include "exynos4210.dtsi" +#include "exynos4412-ppmu-common.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/linux-event-codes.h> + +/ { + model = "Samsung Galaxy S2 (i9100)";+ compatible = "samsung,i9100", "samsung,exynos4210", "samsung,exynos4";+ + + memory@40000000 { + device_type = "memory"; + reg = <0x40000000 0x40000000>; + }; + + vemmc_reg: regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + tsp_reg: regulator-1 { + compatible = "regulator-fixed"; + regulator-name = "TSP_FIXED_VOLTAGES"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpl0 3 GPIO_ACTIVE_HIGH>; + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on; + regulator-always-on; + }; + + cam_af_28v_reg: regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "8M_AF_2.8V_EN"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpk1 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + cam_io_en_reg: regulator-4 { + compatible = "regulator-fixed"; + regulator-name = "CAM_IO_EN"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpe2 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + cam_io_12v_reg: regulator-5 { + compatible = "regulator-fixed"; + regulator-name = "8M_1.2V_EN"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + gpio = <&gpe2 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vt_core_15v_reg: regulator-6 { + compatible = "regulator-fixed"; + regulator-name = "VT_CORE_1.5V"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + gpio = <&gpe2 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + gpio-keys { + compatible = "gpio-keys"; + + vol-down { + gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + label = "volume down"; + debounce-interval = <10>; + }; + + vol-up { + gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + label = "volume up"; + debounce-interval = <10>; + }; + + power { + gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + label = "power"; + debounce-interval = <10>; + wakeup-source; + }; + + ok { + gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; + linux,code = <KEY_OK>; + label = "ok"; + debounce-interval = <10>; + }; + }; + + wlan_pwrseq: sdhci3-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpl1 2 GPIO_ACTIVE_LOW>; + }; + + i2c_max17042_fuel: i2c-gpio-3 { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sda-gpios = <&gpy4 0 GPIO_ACTIVE_HIGH>; + scl-gpios = <&gpy4 1 GPIO_ACTIVE_HIGH>; + i2c-gpio,delay-us = <5>; + + battery@36 { + compatible = "maxim,max17042"; + + interrupt-parent = <&gpx2>; + interrupts = <3 2>; + + pinctrl-0 = <&max17042_fuel_irq>; + pinctrl-names = "default"; + + reg = <0x36>; + maxim,over-heat-temp = <700>; + maxim,over-volt = <4500>; + + }; + }; + + spi-lcd { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + num-chipselects = <1>; + cs-gpios = <&gpy4 3 GPIO_ACTIVE_HIGH>;LD9040 CS is active low, so this board needs probably the same fix a Universal C210 board: https://patchwork.kernel.org/patch/11420231/ Areyou sure it really works now with v5.6-rcX kernels? Or you just got thepanel working only because the bootloader enabled it?
Sorry but the fix looks bogus to me. The spi-gpio driver calls gpiod_set_value(0) when the CS is going *active*, and gpiod_set_value(1) when the CS is going *inactive*. If you use the GPIO_ACTIVE_LOW flag, the levels are inverted, and the CS is high when active, which is the opposite of what you want.
+ sck-gpios = <&gpy3 1 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpy3 3 GPIO_ACTIVE_HIGH>; + + lcd@0 { + compatible = "samsung,ld9040"; + reg = <0>; + + spi-max-frequency = <1200000>; + spi-cpol; + spi-cpha; + + vdd3-supply = <&vmipi_reg>; + vci-supply = <&vcclcd_reg>; + + reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; + power-on-delay = <10>; + reset-delay = <10>; + + panel-width-mm = <90>; + panel-height-mm = <154>; + + display-timings { + timing { + clock-frequency = <23492370>; + hactive = <480>; + vactive = <800>; + hback-porch = <16>; + hfront-porch = <16>; + vback-porch = <2>; + vfront-porch = <28>; + hsync-len = <2>; + vsync-len = <1>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <0>; + pixelclk-active = <0>; + }; + }; + + port { + lcd_ep: endpoint { + remote-endpoint = <&fimd_dpi_ep>; + }; + }; + }; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <0>; + }; + + xusbxti { + compatible = "samsung,clock-xusbxti"; + clock-frequency = <24000000>; + }; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + cooling-maps { + map0 { + /* Corresponds to 800MHz */ + cooling-device = <&cpu0 2 2>; + }; + map1 { + /* Corresponds to 200MHz */ + cooling-device = <&cpu0 4 4>; + }; + }; + }; + }; + +}; + +&camera { + status = "okay"; +}; + +&cpu0 { + cpu0-supply = <&varm_breg>; +}; + +&exynos_usbphy { + status = "okay"; + + vbus-supply = <&safe1_sreg>; +}; + +&fimc_0 { + status = "okay"; ++ assigned-clocks = <&clock CLK_MOUT_FIMC0>, <&clock CLK_SCLK_FIMC0>;+ assigned-clock-parents = <&clock CLK_SCLK_MPLL>; + assigned-clock-rates = <0>, <160000000>; +}; + +&fimc_1 { + status = "okay"; ++ assigned-clocks = <&clock CLK_MOUT_FIMC1>, <&clock CLK_SCLK_FIMC1>;+ assigned-clock-parents = <&clock CLK_SCLK_MPLL>; + assigned-clock-rates = <0>, <160000000>; +}; + +&fimc_2 { + status = "okay"; ++ assigned-clocks = <&clock CLK_MOUT_FIMC2>, <&clock CLK_SCLK_FIMC2>;+ assigned-clock-parents = <&clock CLK_SCLK_MPLL>; + assigned-clock-rates = <0>, <160000000>; +}; + +&fimc_3 { + status = "okay"; ++ assigned-clocks = <&clock CLK_MOUT_FIMC3>, <&clock CLK_SCLK_FIMC3>;+ assigned-clock-parents = <&clock CLK_SCLK_MPLL>; + assigned-clock-rates = <0>, <160000000>; +}; + +&fimd { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + samsung,invert-vden; + samsung,invert-vclk; + + pinctrl-0 = <&lcd_clk>, <&lcd_data24>; + pinctrl-names = "default"; + + port@3 { + reg = <3>; + + fimd_dpi_ep: endpoint { + remote-endpoint = <&lcd_ep>; + }; + }; +}; + +&hsotg { + status = "okay"; + + dr_mode = "otg";The the host mode really works with DWC2? Afair the host mode workedonly when it was rerouted by PHY to the EHCI (at least on UniversalC210board, which is very similar to GS2).
I have to say that I didn't try OTG / host, but it does work fine in gadget mode.
I can change it to dr_mode = "peripheral" for now, if you prefer.
+ vusb_d-supply = <&vusb_reg>; + vusb_a-supply = <&vusbdac_reg>; +}; + +&ehci { + status = "okay"; + + port@0 { + status = "okay"; + }; + + port@1 { + status = "okay"; + }; + + port@2 { + status = "okay"; + }; +};This is the old, obsolete exynos-ehci binding. Please remove 'port' nodes and use standard USB phy bindings like it has been done in the following patch: https://patchwork.kernel.org/patch/11060465/
Will do.
BTW, do you really need all 3 phys/ports?
No idea!
+ + +&i2c_3 { + status = "okay"; + + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + + mxt224-touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + + interrupt-parent = <&gpx0>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + + avdd-supply = <&tsp_reg>; + vdd-supply = <&tsp_reg>; + }; +}; + +&i2c_7 { + status = "okay"; + + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + + pinctrl-0 = <&i2c7_bus>; + pinctrl-names = "default"; + + ak8975@c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + + gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>; + }; +}; + + +&i2c_5 { + status = "okay"; + + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + + pinctrl-0 = <&i2c5_bus>; + pinctrl-names = "default"; + + max8997_pmic@66 { + compatible = "maxim,max8997-pmic"; + reg = <0x66>; + + interrupts-extended = <&gpx0 7 0>, <&gpx2 3 2>; + interrupt-parent = <&gpx0>; + interrupts = <7 IRQ_TYPE_NONE>; + + otg_en-gpios = <&gpx3 3 0>; + usb_sel-gpios = <&gpl0 6 0>; + + max8997,pmic-buck1-uses-gpio-dvs; + max8997,pmic-buck2-uses-gpio-dvs; + max8997,pmic-buck5-uses-gpio-dvs; + + max8997,pmic-ignore-gpiodvs-side-effect; + max8997,pmic-buck125-default-dvs-idx = <0>; + + max8997,pmic-buck125-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>, + <&gpx0 6 GPIO_ACTIVE_HIGH>, + <&gpl0 0 GPIO_ACTIVE_HIGH>; + + max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>, + <950000>, <900000>, + <1100000>, <1000000>, + <950000>, <900000>; + + max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + pinctrl-0 = <&max8997_irq>, <&otg_gp>, <&usb_sel>; + pinctrl-names = "default"; + + regulators { + vadc_reg: LDO1 { + regulator-name = "VADC_3.3V_C210"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + + }; + valive_reg: LDO2 { + regulator-name = "VALIVE_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + + }; + + vusb_reg: LDO3 { + regulator-name = "VUSB_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + vmipi_reg: LDO4 { + regulator-name = "VMIPI_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vhsic_reg: LDO5 { + regulator-name = "VHSIC_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vpda_reg: LDO6 { + regulator-name = "VCC_1.8V_PDA"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcam_reg: LDO7 { + regulator-name = "CAM_ISP_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vusbdac_reg: LDO8 { + regulator-name = "VUSB+VDAC_3.3V_C210"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vccpda_reg: LDO9 { + regulator-name = "VCC_2.8V_PDA"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + vtouch_reg: LDO11 { + regulator-name = "TOUCH_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + vpll_reg: LDO10 { + regulator-name = "VPLL_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vtcam_reg: LDO12 { + regulator-name = "VT_CAM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcclcd_reg: LDO13 { + regulator-name = "VCC_3.0V_LCD"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + vmotor_reg: LDO14 { + regulator-name = "VCC_2.8V_MOTOR"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + vled_reg: LDO15 { + regulator-name = "LED_A_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + camsensor_reg: LDO16 { + regulator-name = "CAM_SENSOR_IO_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vtf_reg: LDO17 { + regulator-name = "VTF_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + vtouchled_reg: LDO18 { + regulator-name = "TOUCH_LED_3.3V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + }; + + vddq_reg: LDO21 { + regulator-name = "VDDQ_M1M2_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + varm_breg: BUCK1 { + //regulator-name = "VARM_1.2V_C210"; + regulator-name = "vdd_arm"; + regulator-min-microvolt = <65000>; + regulator-max-microvolt = <2225000>; + regulator-always-on; + }; + + vint_breg: BUCK2 { + regulator-name = "VINT_1.1V_C210"; + regulator-min-microvolt = <65000>; + regulator-max-microvolt = <2225000>; + regulator-always-on; + }; + + vg3d_breg: BUCK3 { + regulator-name = "G3D_1.1V"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + camisp_breg: BUCK4 { + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vmem_breg: BUCK5 { + regulator-name = "VMEM_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vccsub_breg: BUCK7 { + regulator-name = "VCC_SUB_2.0V"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + safe1_sreg: ESAFEOUT1 { + regulator-name = "SAFEOUT1"; + }; + + safe2_sreg: ESAFEOUT2 { + regulator-name = "SAFEOUT2"; + regulator-boot-on; + }; + + charger_reg: CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <60000>; + regulator-max-microamp = <2580000>; + regulator-always-on; + }; + + chargercv_reg: CHARGER_CV { + regulator-name = "CHARGER_CV"; + regulator-min-microvolt = <3800000>; + regulator-max-microvolt = <4100000>; + regulator-always-on; + }; + + }; + + }; +}; + + +&gpu { + status = "okay"; + + mali-supply = <&vg3d_breg>; + regulator-microvolt-offset = <50000>; + regulator-microsecs-delay = <50>; +}; + + +&sdhci_0 { + status = "okay"; + + bus-width = <8>; + non-removable; + vmmc-supply = <&vemmc_reg>; + + pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_bus8>; + pinctrl-names = "default"; +}; + +&sdhci_2 { + status = "okay"; + + bus-width = <4>; + cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vtf_reg>; + + pinctrl-0 = <&sd2_clk>, <&sd2_cmd>, <&sd2_bus4>; + pinctrl-names = "default"; +}; + +&ehci { + port@0 { + status = "okay"; + }; + + port@1 { + status = "okay"; + }; + + port@2 { + status = "okay"; + }; + +};This is duplicated 'ehci' node, probable an artifact from the earlier rebase. Please remove it.
Right, didn't even notice it. Will remove it and send a V2. Cheers, -Paul
+ + +&sdhci_3 { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + non-removable; + bus-width = <4>; + mmc-pwrseq = <&wlan_pwrseq>; + vmmc-supply = <&vtf_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>; + + brcmf: wifi@1 { + compatible = "brcm,bcm4330-fmac"; + reg = <1>; + + interrupt-parent = <&gpx2>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wake"; + }; +}; + + +&serial_0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&bt_en>, <&bt_res>, <&uart0_data>, <&uart0_fctl>; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + + shutdown-gpios = <&gpl0 4 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpl1 0 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; + }; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_2 { + status = "okay"; +}; + +&serial_3 { + status = "okay"; +}; + +&tmu { + status = "okay"; +}; + + +&pinctrl_0 { + pinctrl-names = "default"; + pinctrl-0 = <&sleep0>; + + + sleep0: sleep-states { + gpa0-0 { + samsung,pins = "gpa0-0"; + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>; + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>; + }; + + gpa0-1 { + samsung,pins = "gpa0-1"; + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT0>; + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>; + }; + + gpa0-2 { + samsung,pins = "gpa0-2"; + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>; + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>; + }; + + gpa0-3 { + samsung,pins = "gpa0-3"; + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>; + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>; + }; + }; +}; + +&pinctrl_1 { + mhl_int: mhl-int { + samsung,pins = "gpf3-5"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + i2c_mhl_bus: i2c-mhl-bus { + samsung,pins = "gpf0-4", "gpf0-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + usb_sel: usb-sel { + samsung,pins = "gpl0-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + samsung,pin-val = <0>; + }; + + bt_en: bt-en { + samsung,pins = "gpl0-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; + samsung,pin-val = <0>; + }; + + bt_res: bt-res { + samsung,pins = "gpl1-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; + samsung,pin-val = <0>; + }; + + + otg_gp: otg-gp { + samsung,pins = "gpx3-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + samsung,pin-val = <0>; + }; + + mag_mhl_gpio: mag-mhl-gpio { + samsung,pins = "gpd0-2"; + samsung,pin-function = <EXYNOS_PIN_FUNC_3>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + + max8997_irq: max8997-irq { + samsung,pins = "gpx0-7"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + max17042_fuel_irq: max17042-fuel-irq { + samsung,pins = "gpx2-3"; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + tsp224_irq: tsp224-irq { + samsung,pins = "gpx0-4"; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + }; +};Best regards -- Marek Szyprowski, PhD Samsung R&D Institute Poland
