Re: [PATCH V13 12/12] PCI: tegra: Add Tegra194 PCIe support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Aug 05, 2019 at 10:24:42PM +0530, Vidya Sagar wrote:

[...]

> > > > IRQs are enabled when you call a suspend_noirq() callback, so the
> > > > blocking API can be used as long as the IRQ descriptor backing
> > > > the IRQ that will wake-up the blocked call is marked as
> > > > IRQF_NO_SUSPEND.
> > > > 
> > > > The problem is not IRQs enabled/disabled at CPU level, the problem is
> > > > the IRQ descriptor of the IRQ required to handle the blocking BPMP call,
> > > > mark it as IRQF_NO_SUSPEND and remove the tegra_bpmp_transfer_atomic()
> > > > call from this code (or please give me a concrete example pinpointing
> > > > why it is needed).
> > > Ideally, using tegra_bpmp_transfer() alone in all paths (.probe() as
> > > well as .resume_noirq()) should have worked as the corresponding IRQ
> > > is already flagged as IRQF_NO_SUSPEND, but, because of the way BPMP-FW
> > > driver in kernel making its interface available through
> > > .resume_early(), tegra_bpmp_transfer() wasn't working as expected and
> > > I pushed a patch (CC'ing you) at
> > > http://patchwork.ozlabs.org/patch/1140973/ to make it .resume_noirq()
> > > from .resume_early().  With that in place, we can just use
> > > tegra_bpmp_trasnfer().  I'll push a new patch with this change once my
> > > BPMP-FW driver patch is approved.
> > 
> > Does this leave you with a resume_noirq() callbacks ordering issue to
> > sort out ?
> Not really.
> 
> > 
> > a.k.a How will you guarantee that the BPMP will resume before the host
> > bridge ?
> It is already taken care of in the following way.  PCIe controller's
> device-tree node has an entry with a phandle of BPMP-FW's node to get
> a handle of it and PCIe driver uses tegra_bpmp_get() API for that.
> This API returns -EPROBE_DEFER if BPMP-FW's driver is not ready yet,
> which guarantees that PCIe driver gets loaded only after BPMP-FW's
> driver and this order is followed during noirq phase also.

OK, thanks, this makes much more sense than the original code.

Lorenzo

> > Thanks,
> > Lorenzo
> > 
> > > Thanks,
> > > Vidya Sagar
> > > > 
> > > > Thanks,
> > > > Lorenzo
> > > > 
> > > > > I'll go ahead and make next patch series with this if this looks fine to you.
> > > > > 
> > > > > > 
> > > > > > > > Actually, if tegra_bpmp_transfer() requires IRQs to be enabled you may
> > > > > > > > even end up in a situation where that blocking call does not wake up
> > > > > > > > because the IRQ in question was disabled in the NOIRQ suspend/resume
> > > > > > > > phase.
> > > > > > > > 
> > > > > > > > [...]
> > > > > > > > 
> > > > > > > > > > > +static int tegra_pcie_dw_probe(struct platform_device *pdev)
> > > > > > > > > > > +{
> > > > > > > > > > > +	const struct tegra_pcie_soc *data;
> > > > > > > > > > > +	struct device *dev = &pdev->dev;
> > > > > > > > > > > +	struct resource *atu_dma_res;
> > > > > > > > > > > +	struct tegra_pcie_dw *pcie;
> > > > > > > > > > > +	struct resource *dbi_res;
> > > > > > > > > > > +	struct pcie_port *pp;
> > > > > > > > > > > +	struct dw_pcie *pci;
> > > > > > > > > > > +	struct phy **phys;
> > > > > > > > > > > +	char *name;
> > > > > > > > > > > +	int ret;
> > > > > > > > > > > +	u32 i;
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
> > > > > > > > > > > +	if (!pcie)
> > > > > > > > > > > +		return -ENOMEM;
> > > > > > > > > > > +
> > > > > > > > > > > +	pci = &pcie->pci;
> > > > > > > > > > > +	pci->dev = &pdev->dev;
> > > > > > > > > > > +	pci->ops = &tegra_dw_pcie_ops;
> > > > > > > > > > > +	pp = &pci->pp;
> > > > > > > > > > > +	pcie->dev = &pdev->dev;
> > > > > > > > > > > +
> > > > > > > > > > > +	data = (struct tegra_pcie_soc *)of_device_get_match_data(dev);
> > > > > > > > > > > +	if (!data)
> > > > > > > > > > > +		return -EINVAL;
> > > > > > > > > > > +	pcie->mode = (enum dw_pcie_device_mode)data->mode;
> > > > > > > > > > > +
> > > > > > > > > > > +	ret = tegra_pcie_dw_parse_dt(pcie);
> > > > > > > > > > > +	if (ret < 0) {
> > > > > > > > > > > +		dev_err(dev, "Failed to parse device tree: %d\n", ret);
> > > > > > > > > > > +		return ret;
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie->pex_ctl_supply = devm_regulator_get(dev, "vddio-pex-ctl");
> > > > > > > > > > > +	if (IS_ERR(pcie->pex_ctl_supply)) {
> > > > > > > > > > > +		dev_err(dev, "Failed to get regulator: %ld\n",
> > > > > > > > > > > +			PTR_ERR(pcie->pex_ctl_supply));
> > > > > > > > > > > +		return PTR_ERR(pcie->pex_ctl_supply);
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie->core_clk = devm_clk_get(dev, "core");
> > > > > > > > > > > +	if (IS_ERR(pcie->core_clk)) {
> > > > > > > > > > > +		dev_err(dev, "Failed to get core clock: %ld\n",
> > > > > > > > > > > +			PTR_ERR(pcie->core_clk));
> > > > > > > > > > > +		return PTR_ERR(pcie->core_clk);
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie->appl_res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> > > > > > > > > > > +						      "appl");
> > > > > > > > > > > +	if (!pcie->appl_res) {
> > > > > > > > > > > +		dev_err(dev, "Failed to find \"appl\" region\n");
> > > > > > > > > > > +		return PTR_ERR(pcie->appl_res);
> > > > > > > > > > > +	}
> > > > > > > > > > > +	pcie->appl_base = devm_ioremap_resource(dev, pcie->appl_res);
> > > > > > > > > > > +	if (IS_ERR(pcie->appl_base))
> > > > > > > > > > > +		return PTR_ERR(pcie->appl_base);
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie->core_apb_rst = devm_reset_control_get(dev, "apb");
> > > > > > > > > > > +	if (IS_ERR(pcie->core_apb_rst)) {
> > > > > > > > > > > +		dev_err(dev, "Failed to get APB reset: %ld\n",
> > > > > > > > > > > +			PTR_ERR(pcie->core_apb_rst));
> > > > > > > > > > > +		return PTR_ERR(pcie->core_apb_rst);
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	phys = devm_kcalloc(dev, pcie->phy_count, sizeof(*phys), GFP_KERNEL);
> > > > > > > > > > > +	if (!phys)
> > > > > > > > > > > +		return PTR_ERR(phys);
> > > > > > > > > > > +
> > > > > > > > > > > +	for (i = 0; i < pcie->phy_count; i++) {
> > > > > > > > > > > +		name = kasprintf(GFP_KERNEL, "p2u-%u", i);
> > > > > > > > > > > +		if (!name) {
> > > > > > > > > > > +			dev_err(dev, "Failed to create P2U string\n");
> > > > > > > > > > > +			return -ENOMEM;
> > > > > > > > > > > +		}
> > > > > > > > > > > +		phys[i] = devm_phy_get(dev, name);
> > > > > > > > > > > +		kfree(name);
> > > > > > > > > > > +		if (IS_ERR(phys[i])) {
> > > > > > > > > > > +			ret = PTR_ERR(phys[i]);
> > > > > > > > > > > +			dev_err(dev, "Failed to get PHY: %d\n", ret);
> > > > > > > > > > > +			return ret;
> > > > > > > > > > > +		}
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie->phys = phys;
> > > > > > > > > > > +
> > > > > > > > > > > +	dbi_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
> > > > > > > > > > > +	if (!dbi_res) {
> > > > > > > > > > > +		dev_err(dev, "Failed to find \"dbi\" region\n");
> > > > > > > > > > > +		return PTR_ERR(dbi_res);
> > > > > > > > > > > +	}
> > > > > > > > > > > +	pcie->dbi_res = dbi_res;
> > > > > > > > > > > +
> > > > > > > > > > > +	pci->dbi_base = devm_ioremap_resource(dev, dbi_res);
> > > > > > > > > > > +	if (IS_ERR(pci->dbi_base))
> > > > > > > > > > > +		return PTR_ERR(pci->dbi_base);
> > > > > > > > > > > +
> > > > > > > > > > > +	/* Tegra HW locates DBI2 at a fixed offset from DBI */
> > > > > > > > > > > +	pci->dbi_base2 = pci->dbi_base + 0x1000;
> > > > > > > > > > > +
> > > > > > > > > > > +	atu_dma_res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> > > > > > > > > > > +						   "atu_dma");
> > > > > > > > > > > +	if (!atu_dma_res) {
> > > > > > > > > > > +		dev_err(dev, "Failed to find \"atu_dma\" region\n");
> > > > > > > > > > > +		return PTR_ERR(atu_dma_res);
> > > > > > > > > > > +	}
> > > > > > > > > > > +	pcie->atu_dma_res = atu_dma_res;
> > > > > > > > > > > +	pci->atu_base = devm_ioremap_resource(dev, atu_dma_res);
> > > > > > > > > > > +	if (IS_ERR(pci->atu_base))
> > > > > > > > > > > +		return PTR_ERR(pci->atu_base);
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie->core_rst = devm_reset_control_get(dev, "core");
> > > > > > > > > > > +	if (IS_ERR(pcie->core_rst)) {
> > > > > > > > > > > +		dev_err(dev, "Failed to get core reset: %ld\n",
> > > > > > > > > > > +			PTR_ERR(pcie->core_rst));
> > > > > > > > > > > +		return PTR_ERR(pcie->core_rst);
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	pp->irq = platform_get_irq_byname(pdev, "intr");
> > > > > > > > > > > +	if (!pp->irq) {
> > > > > > > > > > > +		dev_err(dev, "Failed to get \"intr\" interrupt\n");
> > > > > > > > > > > +		return -ENODEV;
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	ret = devm_request_irq(dev, pp->irq, tegra_pcie_irq_handler,
> > > > > > > > > > > +			       IRQF_SHARED, "tegra-pcie-intr", pcie);
> > > > > > > > > > > +	if (ret) {
> > > > > > > > > > > +		dev_err(dev, "Failed to request IRQ %d: %d\n", pp->irq, ret);
> > > > > > > > > > > +		return ret;
> > > > > > > > > > > +	}
> > > > > > > > > > > +
> > > > > > > > > > > +	pcie->bpmp = tegra_bpmp_get(dev);
> > > > > > > > > > > +	if (IS_ERR(pcie->bpmp))
> > > > > > > > > > > +		return PTR_ERR(pcie->bpmp);
> > > > > > > > > > > +
> > > > > > > > > > > +	platform_set_drvdata(pdev, pcie);
> > > > > > > > > > > +
> > > > > > > > > > > +	if (pcie->mode == DW_PCIE_RC_TYPE) {
> > > > > > > > > > > +		ret = tegra_pcie_config_rp(pcie);
> > > > > > > > > > > +		if (ret && ret != -ENOMEDIUM)
> > > > > > > > > > > +			goto fail;
> > > > > > > > > > > +		else
> > > > > > > > > > > +			return 0;
> > > > > > > > > > 
> > > > > > > > > > So if the link is not up we still go ahead and make probe
> > > > > > > > > > succeed. What for ?
> > > > > > > > > We may need root port to be available to support hot-plugging of
> > > > > > > > > endpoint devices, so, we don't fail the probe.
> > > > > > > > 
> > > > > > > > We need it or we don't. If you do support hotplugging of endpoint
> > > > > > > > devices point me at the code, otherwise link up failure means
> > > > > > > > failure to probe.
> > > > > > > Currently hotplugging of endpoint is not supported, but it is one of
> > > > > > > the use cases that we may add support for in future.
> > > > > > 
> > > > > > You should elaborate on this, I do not understand what you mean,
> > > > > > either the root port(s) supports hotplug or it does not.
> > > > > > 
> > > > > > > But, why should we fail probe if link up doesn't happen? As such,
> > > > > > > nothing went wrong in terms of root port initialization right?  I
> > > > > > > checked other DWC based implementations and following are not failing
> > > > > > > the probe pci-dra7xx.c, pcie-armada8k.c, pcie-artpec6.c, pcie-histb.c,
> > > > > > > pcie-kirin.c, pcie-spear13xx.c, pci-exynos.c, pci-imx6.c,
> > > > > > > pci-keystone.c, pci-layerscape.c
> > > > > > > 
> > > > > > > Although following do fail the probe if link is not up.  pcie-qcom.c,
> > > > > > > pcie-uniphier.c, pci-meson.c
> > > > > > > 
> > > > > > > So, to me, it looks more like a choice we can make whether to fail the
> > > > > > > probe or not and in this case we are choosing not to fail.
> > > > > > 
> > > > > > I disagree. I had an offline chat with Bjorn and whether link-up should
> > > > > > fail the probe or not depends on whether the root port(s) is hotplug
> > > > > > capable or not and this in turn relies on the root port "Slot
> > > > > > implemented" bit in the PCI Express capabilities register.
> > > > > > 
> > > > > > It is a choice but it should be based on evidence.
> > > > > > 
> > > > > > Lorenzo
> > > > > With Bjorn's latest comment on top of this, I think we are good not to fail
> > > > > the probe here.
> > > > > 
> > > > > - Vidya Sagar
> > > > > > 
> > > > > 
> > > 
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux