Re: [PATCH v2 07/20] ARM: dts: imx7-colibri: fix 1.8V/UHS support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, 2019-07-31 at 09:56 -0300, Fabio Estevam wrote:
> On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
> <philippe.schenker@xxxxxxxxxxx> wrote:
> > From: Stefan Agner <stefan.agner@xxxxxxxxxxx>
> > 
> > Add pinmuxing and do not specify voltage restrictions in the
> > module level device tree.
> 
> It would be nice to explain the reason for doing this.

This commit is in preparation of another patch that didn't made into this
patchset (downstream stuff in there). But I will do another patch on top that
will use this patch here. That should anyway be in mainline.

Philippe

> 
> > Signed-off-by: Stefan Agner <stefan.agner@xxxxxxxxxxx>
> > Signed-off-by: Philippe Schenker <philippe.schenker@xxxxxxxxxxx>
> > ---
> > 
> > Changes in v2: None
> > 
> >  arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
> >  1 file changed, 22 insertions(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-
> > colibri.dtsi
> > index 16d1a1ed1aff..67f5e0c87fdc 100644
> > --- a/arch/arm/boot/dts/imx7-colibri.dtsi
> > +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
> > @@ -326,7 +326,6 @@
> >  &usdhc1 {
> >         pinctrl-names = "default";
> >         pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
> > -       no-1-8-v;
> >         cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
> >         disable-wp;
> >         vqmmc-supply = <&reg_LDO2>;
> > @@ -671,6 +670,28 @@
> >                 >;
> >         };
> > 
> > +       pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
> > +               fsl,pins = <
> > +                       MX7D_PAD_SD1_CMD__SD1_CMD       0x5a
> > +                       MX7D_PAD_SD1_CLK__SD1_CLK       0x1a
> > +                       MX7D_PAD_SD1_DATA0__SD1_DATA0   0x5a
> > +                       MX7D_PAD_SD1_DATA1__SD1_DATA1   0x5a
> > +                       MX7D_PAD_SD1_DATA2__SD1_DATA2   0x5a
> > +                       MX7D_PAD_SD1_DATA3__SD1_DATA3   0x5a
> > +               >;
> > +       };
> > +
> > +       pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
> > +               fsl,pins = <
> > +                       MX7D_PAD_SD1_CMD__SD1_CMD       0x5b
> > +                       MX7D_PAD_SD1_CLK__SD1_CLK       0x1b
> > +                       MX7D_PAD_SD1_DATA0__SD1_DATA0   0x5b
> > +                       MX7D_PAD_SD1_DATA1__SD1_DATA1   0x5b
> > +                       MX7D_PAD_SD1_DATA2__SD1_DATA2   0x5b
> > +                       MX7D_PAD_SD1_DATA3__SD1_DATA3   0x5b
> > +               >;
> > +       };
> 
> You add the entries for 100MHz and 200MHz, but I don't see them being
> referenced anywhere.




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux