On 2019-07-31 16:52, Philippe Schenker wrote:
> On Wed, 2019-07-31 at 09:56 -0300, Fabio Estevam wrote:
>> On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
>> <philippe.schenker@xxxxxxxxxxx> wrote:
>> > From: Stefan Agner <stefan.agner@xxxxxxxxxxx>
>> >
>> > Add pinmuxing and do not specify voltage restrictions in the
>> > module level device tree.
>>
>> It would be nice to explain the reason for doing this.
>
> This commit is in preparation of another patch that didn't made into this
> patchset (downstream stuff in there). But I will do another patch on top that
> will use this patch here. That should anyway be in mainline.
I guess what Fabio meant here is explain this patch.
The commit message really could be improved, e.g.:
Add pinmuxing and do not specify voltage restrictions for the usdhc
instance
available on the modules edge connector. This allows to use SD-cards
with
higher transfer modes if supported by the carrier board.
--
Stefan
>
> Philippe
>
>>
>> > Signed-off-by: Stefan Agner <stefan.agner@xxxxxxxxxxx>
>> > Signed-off-by: Philippe Schenker <philippe.schenker@xxxxxxxxxxx>
>> > ---
>> >
>> > Changes in v2: None
>> >
>> > arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
>> > 1 file changed, 22 insertions(+), 1 deletion(-)
>> >
>> > diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-
>> > colibri.dtsi
>> > index 16d1a1ed1aff..67f5e0c87fdc 100644
>> > --- a/arch/arm/boot/dts/imx7-colibri.dtsi
>> > +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
>> > @@ -326,7 +326,6 @@
>> > &usdhc1 {
>> > pinctrl-names = "default";
>> > pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
>> > - no-1-8-v;
>> > cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
>> > disable-wp;
>> > vqmmc-supply = <®_LDO2>;
>> > @@ -671,6 +670,28 @@
>> > >;
>> > };
>> >
>> > + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
>> > + fsl,pins = <
>> > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
>> > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
>> > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
>> > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
>> > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
>> > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
>> > + >;
>> > + };
>> > +
>> > + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
>> > + fsl,pins = <
>> > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
>> > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
>> > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
>> > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
>> > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
>> > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
>> > + >;
>> > + };
>>
>> You add the entries for 100MHz and 200MHz, but I don't see them being
>> referenced anywhere.
