On 7/8/19 6:06 PM, dongchun.zhu@xxxxxxxxxxxx wrote:
> From: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
>
> This patch adds a V4L2 sub-device driver for DW9768 lens voice coil,
> and provides control to set the desired focus.
>
> The DW9807 is a 10 bit DAC from Dongwoon, designed for linear
> control of voice coil motor.
>
> Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
> ---
> MAINTAINERS | 1 +
> drivers/media/i2c/Kconfig | 10 +
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/dw9768.c | 458 +++++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 470 insertions(+)
> create mode 100644 drivers/media/i2c/dw9768.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 8f6ac93..17152d7 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -4877,6 +4877,7 @@ M: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
> L: linux-media@xxxxxxxxxxxxxxx
> T: git git://linuxtv.org/media_tree.git
> S: Maintained
> +F: drivers/media/i2c/dw9768.c
> F: Documentation/devicetree/bindings/media/i2c/dongwoon,dw9768.txt
>
> DONGWOON DW9807 LENS VOICE COIL DRIVER
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index 7793358..8ff6c95 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -1014,6 +1014,16 @@ config VIDEO_DW9714
> capability. This is designed for linear control of
> voice coil motors, controlled via I2C serial interface.
>
> +config VIDEO_DW9768
> + tristate "DW9768 lens voice coil support"
> + depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER
> + depends on VIDEO_V4L2_SUBDEV_API
> + help
> + This is a driver for the DW9768 camera lens voice coil.
> + DW9768 is a 10 bit DAC with 100mA output current sink
> + capability. This is designed for linear control of
> + voice coil motors, controlled via I2C serial interface.
> +
> config VIDEO_DW9807_VCM
> tristate "DW9807 lens voice coil support"
> depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index d8ad9da..944fbf6 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -24,6 +24,7 @@ obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o
> obj-$(CONFIG_VIDEO_AD5820) += ad5820.o
> obj-$(CONFIG_VIDEO_AK7375) += ak7375.o
> obj-$(CONFIG_VIDEO_DW9714) += dw9714.o
> +obj-$(CONFIG_VIDEO_DW9768) += dw9768.o
> obj-$(CONFIG_VIDEO_DW9807_VCM) += dw9807-vcm.o
> obj-$(CONFIG_VIDEO_ADV7170) += adv7170.o
> obj-$(CONFIG_VIDEO_ADV7175) += adv7175.o
> diff --git a/drivers/media/i2c/dw9768.c b/drivers/media/i2c/dw9768.c
> new file mode 100644
> index 0000000..f5b5591
> --- /dev/null
> +++ b/drivers/media/i2c/dw9768.c
> @@ -0,0 +1,458 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018 MediaTek Inc.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/pm_runtime.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-subdev.h>
> +
> +#define DW9768_VOLTAGE_ANALOG 2800000
> +#define DW9768_NAME "dw9768"
> +#define DW9768_MAX_FOCUS_POS 1023
> +/*
> + * This sets the minimum granularity for the focus positions.
> + * A value of 1 gives maximum accuracy for a desired focus position
> + */
> +#define DW9768_FOCUS_STEPS 1
> +
> +#define DW9768_CTRL_DELAY_US 5000
> +
> +#define DW9768_REG_DAC_MSB 0x03
> +#define DW9768_REG_DAC_LSB 0x04
> +#define DW9768_REG_NULL 0xff
> +
> +#define DW9768_DAC_SHIFT 8
> +
> +#define DW9768_REG_VALUE_16BIT 2
> +
> +/* dw9768 device structure */
> +struct dw9768_device {
> + struct v4l2_ctrl_handler ctrls;
> + struct v4l2_subdev sd;
> + struct regulator *analog_regulator;
> + /*
> + * Serialize control access, get/set format, get selection
> + * and start streaming.
> + */
> + struct mutex power_lock;
> +
> + int power_count;
> + bool standby;
> +};
> +
> +static inline struct dw9768_device *to_dw9768_vcm(struct v4l2_ctrl *ctrl)
> +{
> + return container_of(ctrl->handler, struct dw9768_device, ctrls);
> +}
> +
> +static inline struct dw9768_device *sd_to_dw9768_vcm(struct v4l2_subdev *subdev)
> +{
> + return container_of(subdev, struct dw9768_device, sd);
> +}
> +
> +static int dw9768_i2c_write(struct dw9768_device *dw9768_dev, u8 *data,
> + int size)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&dw9768_dev->sd);
> + struct i2c_msg msg;
> + u8 *w_buf = NULL;
> + u8 retry_cnt = 3;
> + int ret;
> +
> + if (!client->adapter)
> + return -ENODEV;
> +
> + if (size != 1 && size != 2)
> + return -EINVAL;
> +
> + memset(&msg, 0, sizeof(struct i2c_msg));
> +
> + w_buf = kzalloc(size, GFP_KERNEL);
> + if (!w_buf)
> + return -1;
return -ENOMEM;
> +
> + memcpy(w_buf, data, size);
> +
> + msg.addr = client->addr;
> + msg.flags = 0;
> + msg.len = size;
> + msg.buf = w_buf;
> +
> + do {
> + ret = i2c_transfer(client->adapter, &msg, 1);
> + if (ret != 1)
> + dev_err(&client->dev, "write fail, ret:%d, retry:%d\n",
> + ret, retry_cnt);
> + else
> + break;
> + retry_cnt--;
> + } while (retry_cnt != 0);
> +
> + if (retry_cnt == 0) {
> + dev_err(&client->dev, "i2c write fail(%d)\n", ret);
> + return -EIO;
> + }
> +
> + kfree(w_buf);
> +
> + return 0;
> +}
> +
> +static int dw9768_release(struct dw9768_device *dw9768_dev)
> +{
> + unsigned char i;
> + int ret;
> +
> + char puSendCmdArray[4][2] = {
> + {0x02, 0x00}, {DW9768_REG_NULL, DW9768_REG_NULL},
> + {0x01, 0x00}, {DW9768_REG_NULL, DW9768_REG_NULL},
> + };
> +
> + for (i = 0; i < (sizeof(puSendCmdArray) / sizeof(char)) /
> + (sizeof(puSendCmdArray[0]) / sizeof(char)); i++) {> + if (puSendCmdArray[i][0] != DW9768_REG_NULL) {
> + ret = dw9768_i2c_write(dw9768_dev, puSendCmdArray[i],
> + DW9768_REG_VALUE_16BIT);
> + if (ret < 0)
> + return ret;
> + } else {
> + usleep_range(DW9768_CTRL_DELAY_US,
> + DW9768_CTRL_DELAY_US + 100);
> + }
> + }
Can we make this block more simple? I think the loop is not necessary.
> +
> + return 0;
> +}
> +
> +static int dw9768_init(struct dw9768_device *dw9768_dev)
> +{
> + unsigned char i;
> + int ret;
> +
> + char puSendCmdArray[5][2] = {
> + {0x02, 0x02}, {DW9768_REG_NULL, DW9768_REG_NULL},
> + {0x06, 0x41}, {0x07, 0x39}, {DW9768_REG_NULL, DW9768_REG_NULL},
> + };
> +
> + for (i = 0; i < (sizeof(puSendCmdArray) / sizeof(char)) /
> + (sizeof(puSendCmdArray[0]) / sizeof(char)); i++) {
> + if (puSendCmdArray[i][0] != DW9768_REG_NULL) {
> + ret = dw9768_i2c_write(dw9768_dev, puSendCmdArray[i],
> + DW9768_REG_VALUE_16BIT);
> + if (ret < 0)
> + return ret;
> + } else {
> + usleep_range(DW9768_CTRL_DELAY_US,
> + DW9768_CTRL_DELAY_US + 100);
> + }
> + }
Ditto.
> +
> + return 0;
> +}
> +
> +/*
> + * Power handling
> + */
> +static int dw9768_power_off(struct dw9768_device *dw9768_dev, bool standby)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&dw9768_dev->sd);
> + int ret;
> +
> + /*
> + * Go to standby first as real power off my be denied by the hardware
typo? "may be denied"
> + * (single power line control for both dw9768_dev and sensor).
> + */
> + if (standby) {
> + dw9768_dev->standby = true;
> + ret = dw9768_release(dw9768_dev);
> + if (ret)
> + dev_err(&client->dev, "dw9768_release failed!\n");
> + }
> + ret = regulator_disable(dw9768_dev->analog_regulator);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int dw9768_power_on(struct dw9768_device *dw9768_dev, bool restore)
> +{
> + int ret;
> +
> + ret = regulator_enable(dw9768_dev->analog_regulator);
> + if (ret < 0)
> + return ret;
> +
> + if (restore) {
> + /* Restore the hardware settings. */
> + dw9768_dev->standby = false;
> + ret = dw9768_init(dw9768_dev);
> + if (ret < 0)
> + goto fail;
> + }
> +
> + return 0;
> +
> +fail:
> + dw9768_dev->standby = true;
> + regulator_disable(dw9768_dev->analog_regulator);
> +
> + return ret;
> +}
> +
> +/*
> + * Calculate status word and write it to the device based on current
> + * values of V4L2 controls. It is assumed that the stored V4L2 control
> + * values are properly limited and rounded.
> + */
> +static int dw9768_update_hw(struct dw9768_device *dw9768_dev, u16 val)
> +{
> + unsigned char i;
> + int ret;
> +
> + char puSendCmdArray[2][2] = {
> + {DW9768_REG_DAC_MSB, (char)(val >> DW9768_DAC_SHIFT)},
> + {DW9768_REG_DAC_LSB, (char)(val & 0xFF)},
> + };
> +
> + for (i = 0; i < (sizeof(puSendCmdArray) / sizeof(char)) /
> + (sizeof(puSendCmdArray[0]) / sizeof(char)); i++) {
> + ret = dw9768_i2c_write(dw9768_dev, puSendCmdArray[i],
> + DW9768_REG_VALUE_16BIT);
> + if (ret)
> + return ret;
> + }
ditto.
> +
> + return 0;
> +}
> +
> +static int dw9768_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct dw9768_device *dw9768_dev = to_dw9768_vcm(ctrl);
> +
> + if (ctrl->id == V4L2_CID_FOCUS_ABSOLUTE)
> + return dw9768_update_hw(dw9768_dev, ctrl->val);
> +
> + return 0;
> +}
> +
> +static const struct v4l2_ctrl_ops dw9768_vcm_ctrl_ops = {
> + .s_ctrl = dw9768_set_ctrl,
> +};
> +
> +static int
> +dw9768_set_power(struct v4l2_subdev *subdev, int on)
> +{
> + struct dw9768_device *dw9768_dev = sd_to_dw9768_vcm(subdev);
> + int ret = 0;
> +
> + mutex_lock(&dw9768_dev->power_lock);
> +
> + /*
> + * If the power count is modified from 0 to != 0 or from != 0 to 0,
> + * update the power state.
> + */
> + if (dw9768_dev->power_count == !on) {
> + ret = on ? dw9768_power_on(dw9768_dev, true) :
> + dw9768_power_off(dw9768_dev, true);
> + if (ret < 0)
> + goto done;
> + }
> +
> + /* Update the power count. */
> + dw9768_dev->power_count += on ? 1 : -1;
> + WARN_ON(dw9768_dev->power_count < 0);
> +
> +done:
> + mutex_unlock(&dw9768_dev->power_lock);
> + return ret;
> +}
> +
> +static int dw9768_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> + return dw9768_set_power(sd, 1);
> +}
> +
> +static int dw9768_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
> +{
> + return dw9768_set_power(sd, 0);
> +}
I am a little confused about the pm control here.
Could we use the pm generic APIs to help do this?
> +
> +static const struct v4l2_subdev_internal_ops dw9768_int_ops = {
> + .open = dw9768_open,
> + .close = dw9768_close,
> +};
> +
> +static const struct v4l2_subdev_ops dw9768_ops = { };
> +
> +static void dw9768_subdev_cleanup(struct dw9768_device *dw9768_dev)
> +{
> + v4l2_async_unregister_subdev(&dw9768_dev->sd);
> + v4l2_ctrl_handler_free(&dw9768_dev->ctrls);
> + media_entity_cleanup(&dw9768_dev->sd.entity);
> +}
> +
> +static int dw9768_init_controls(struct dw9768_device *dw9768_dev)
> +{
> + struct v4l2_ctrl_handler *hdl = &dw9768_dev->ctrls;
> + const struct v4l2_ctrl_ops *ops = &dw9768_vcm_ctrl_ops;
> +
> + v4l2_ctrl_handler_init(hdl, 1);
> +
> + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_FOCUS_ABSOLUTE,
> + 0, DW9768_MAX_FOCUS_POS, DW9768_FOCUS_STEPS, 0);
> +
> + if (hdl->error) {
> + dev_err(dw9768_dev->sd.dev, "%s fail error: 0x%x\n",
> + __func__, hdl->error);
> + return hdl->error;
> + }
> +
> + dw9768_dev->sd.ctrl_handler = hdl;
> +
> + return 0;
> +}
> +
> +static int dw9768_probe(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct dw9768_device *dw9768_dev;
> + int rval;
> +
> + dw9768_dev = devm_kzalloc(&client->dev, sizeof(*dw9768_dev),
> + GFP_KERNEL);
> + if (!dw9768_dev)
> + return -ENOMEM;
> +
> + dw9768_dev->analog_regulator = devm_regulator_get(dev, "afvdd");
> + if (IS_ERR(dw9768_dev->analog_regulator)) {
> + dev_err(dev, "cannot get analog regulator\n");
> + return PTR_ERR(dw9768_dev->analog_regulator);
> + }
> +
> + rval = regulator_set_voltage(dw9768_dev->analog_regulator,
> + DW9768_VOLTAGE_ANALOG,
> + DW9768_VOLTAGE_ANALOG);
> + if (rval < 0) {
> + dev_err(dev, "cannot set analog voltage\n");
> + return rval;
> + }
> +
> + mutex_init(&dw9768_dev->power_lock);
> +
> + v4l2_i2c_subdev_init(&dw9768_dev->sd, client, &dw9768_ops);
> + dw9768_dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> + dw9768_dev->sd.internal_ops = &dw9768_int_ops;
> +
> + rval = dw9768_init_controls(dw9768_dev);
> + if (rval)
> + goto err_cleanup;
> +
> + rval = media_entity_pads_init(&dw9768_dev->sd.entity, 0, NULL);
> + if (rval < 0)
> + goto err_cleanup;
> +
> + dw9768_dev->sd.entity.function = MEDIA_ENT_F_LENS;
> +
> + rval = v4l2_async_register_subdev(&dw9768_dev->sd);
> + if (rval < 0)
> + goto err_cleanup;
> +
> + pm_runtime_set_active(dev);
> + pm_runtime_enable(dev);
> + pm_runtime_idle(dev);
> +
> + return 0;
> +
> +err_cleanup:
> + mutex_destroy(&dw9768_dev->power_lock);
> + dw9768_subdev_cleanup(dw9768_dev);
> + dev_err(dev, "Probe failed: %d\n", rval);
> + return rval;
> +}
> +
> +static int dw9768_remove(struct i2c_client *client)
> +{
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9768_device *dw9768_dev = sd_to_dw9768_vcm(sd);
> +
> + pm_runtime_disable(&client->dev);
> + dw9768_subdev_cleanup(dw9768_dev);
> +
> + return 0;
> +}
> +
> +/*
> + * This function sets the vcm position, so it consumes least current
> + * The lens position is gradually moved in units of DW9768_CTRL_STEPS,
> + * to make the movements smoothly.
> + */
> +static int __maybe_unused dw9768_vcm_suspend(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9768_device *dw9768_dev = sd_to_dw9768_vcm(sd);
> +
> + if (!dw9768_dev->power_count)
> + return 0;
> +
> + return dw9768_power_off(dw9768_dev, false);
> +}
> +
> +/*
> + * This function sets the vcm position to the value set by the user
> + * through v4l2_ctrl_ops s_ctrl handler
> + * The lens position is gradually moved in units of DW9768_CTRL_STEPS,
> + * to make the movements smoothly.
> + */
> +static int __maybe_unused dw9768_vcm_resume(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct dw9768_device *dw9768_dev = sd_to_dw9768_vcm(sd);
> +
> + if (!dw9768_dev->power_count)
> + return 0;
> +
> + return dw9768_power_on(dw9768_dev, true);
> +}
> +
> +static const struct i2c_device_id dw9768_id_table[] = {
> + { DW9768_NAME, 0 },
> + { { 0 } }
> +};
> +MODULE_DEVICE_TABLE(i2c, dw9768_id_table);
> +
> +static const struct of_device_id dw9768_of_table[] = {
> + { .compatible = "dongwoon,dw9768" },
> + { { 0 } }
> +};
> +MODULE_DEVICE_TABLE(of, dw9768_of_table);
> +
> +static const struct dev_pm_ops dw9768_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(dw9768_vcm_suspend, dw9768_vcm_resume)
> + SET_RUNTIME_PM_OPS(dw9768_vcm_suspend, dw9768_vcm_resume, NULL)
> +};
> +
> +static struct i2c_driver dw9768_i2c_driver = {
> + .driver = {
> + .name = DW9768_NAME,
> + .pm = &dw9768_pm_ops,
> + .of_match_table = dw9768_of_table,
> + },
> + .probe_new = dw9768_probe,
> + .remove = dw9768_remove,
> + .id_table = dw9768_id_table,
> +};
> +
> +module_i2c_driver(dw9768_i2c_driver);
> +
> +MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("DW9768 VCM driver");
> +MODULE_LICENSE("GPL v2");
>
