From: Louis Yu <louis.yu@xxxxxxxxxxxx> Add suspend/resume callback to disable/enable Mediatek thermal sensor respectively. Since thermal power domain is off in suspend, thermal driver needs re-initialization during resume. Signed-off-by: Louis Yu <louis.yu@xxxxxxxxxxxx> Signed-off-by: Michael Kao <michael.kao@xxxxxxxxxxxx> --- This patch series base on these patches [1][2][3]. [1]thermal: mediatek: mt8183: fix bank number settings (https://patchwork.kernel.org/patch/10938817/) [2]thermal: mediatek: add another get_temp ops for thermal sensors (https://patchwork.kernel.org/patch/10938829/) [3]thermal: mediatek: use spinlock to protect PTPCORESEL (https://patchwork.kernel.org/patch/10938841/) drivers/thermal/mtk_thermal.c | 134 +++++++++++++++++++++++++++++++++++++++--- 1 file changed, 125 insertions(+), 9 deletions(-) diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c index 3d01153..61d4114 100644 --- a/drivers/thermal/mtk_thermal.c +++ b/drivers/thermal/mtk_thermal.c @@ -30,6 +30,7 @@ #include <linux/thermal.h> #include <linux/reset.h> #include <linux/types.h> +#include <linux/iopoll.h> /* AUXADC Registers */ #define AUXADC_CON1_SET_V 0x008 @@ -39,6 +40,8 @@ #define APMIXED_SYS_TS_CON1 0x604 +#define APMIXED_SYS_TS_CON1_BUFFER_OFF 0x30 + /* Thermal Controller Registers */ #define TEMP_MONCTL0 0x000 #define TEMP_MONCTL1 0x004 @@ -46,6 +49,7 @@ #define TEMP_MONIDET0 0x014 #define TEMP_MONIDET1 0x018 #define TEMP_MSRCTL0 0x038 +#define TEMP_MSRCTL1 0x03c #define TEMP_AHBPOLL 0x040 #define TEMP_AHBTO 0x044 #define TEMP_ADCPNP0 0x048 @@ -95,6 +99,9 @@ #define TEMP_ADCVALIDMASK_VALID_HIGH BIT(5) #define TEMP_ADCVALIDMASK_VALID_POS(bit) (bit) +#define TEMP_MSRCTL1_BUS_STA (BIT(0) | BIT(7)) +#define TEMP_MSRCTL1_SENSING_POINTS_PAUSE 0x10E + /* MT8173 thermal sensors */ #define MT8173_TS1 0 #define MT8173_TS2 1 @@ -266,6 +273,10 @@ struct mtk_thermal_data { struct mtk_thermal { struct device *dev; void __iomem *thermal_base; + void __iomem *apmixed_base; + void __iomem *auxadc_base; + u64 apmixed_phys_base; + u64 auxadc_phys_base; struct clk *clk_peri_therm; struct clk *clk_auxadc; @@ -795,6 +806,42 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num, mtk_thermal_put_bank(bank); } +static int mtk_thermal_disable_sensing(struct mtk_thermal *mt, int num) +{ + struct mtk_thermal_bank *bank = &mt->banks[num]; + u32 val; + unsigned long timeout; + void __iomem *addr; + int ret = 0; + + bank->id = num; + bank->mt = mt; + + mtk_thermal_get_bank(bank); + + val = readl(mt->thermal_base + TEMP_MSRCTL1); + /* pause periodic temperature measurement for sensing points */ + writel(val | TEMP_MSRCTL1_SENSING_POINTS_PAUSE, + mt->thermal_base + TEMP_MSRCTL1); + + /* wait until temperature measurement bus idle */ + timeout = jiffies + HZ; + addr = mt->thermal_base + TEMP_MSRCTL1; + + ret = readl_poll_timeout(addr, val, (val & TEMP_MSRCTL1_BUS_STA) == 0x0, + 0, timeout); + if (ret < 0) + goto out; + + /* disable periodic temperature meausrement on sensing points */ + writel(0x0, mt->thermal_base + TEMP_MONCTL0); + +out: + mtk_thermal_put_bank(bank); + + return ret; +} + static u64 of_get_phys_base(struct device_node *np) { u64 size64; @@ -917,7 +964,6 @@ static int mtk_thermal_probe(struct platform_device *pdev) struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node; struct mtk_thermal *mt; struct resource *res; - u64 auxadc_phys_base, apmixed_phys_base; struct thermal_zone_device *tzdev; struct mtk_thermal_zone *tz; @@ -954,11 +1000,11 @@ static int mtk_thermal_probe(struct platform_device *pdev) return -ENODEV; } - auxadc_phys_base = of_get_phys_base(auxadc); + mt->auxadc_phys_base = of_get_phys_base(auxadc); of_node_put(auxadc); - if (auxadc_phys_base == OF_BAD_ADDR) { + if (mt->auxadc_phys_base == OF_BAD_ADDR) { dev_err(&pdev->dev, "Can't get auxadc phys address\n"); return -EINVAL; } @@ -969,11 +1015,12 @@ static int mtk_thermal_probe(struct platform_device *pdev) return -ENODEV; } - apmixed_phys_base = of_get_phys_base(apmixedsys); + mt->apmixed_phys_base = of_get_phys_base(apmixedsys); + mt->apmixed_base = of_iomap(apmixedsys, 0); of_node_put(apmixedsys); - if (apmixed_phys_base == OF_BAD_ADDR) { + if (mt->apmixed_phys_base == OF_BAD_ADDR) { dev_err(&pdev->dev, "Can't get auxadc phys address\n"); return -EINVAL; } @@ -985,19 +1032,19 @@ static int mtk_thermal_probe(struct platform_device *pdev) ret = clk_prepare_enable(mt->clk_auxadc); if (ret) { dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret); - return ret; + goto err_disable_clk_auxadc; } ret = clk_prepare_enable(mt->clk_peri_therm); if (ret) { dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret); - goto err_disable_clk_auxadc; + goto err_disable_clk_peri_therm; } for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++) for (i = 0; i < mt->conf->num_banks; i++) - mtk_thermal_init_bank(mt, i, apmixed_phys_base, - auxadc_phys_base, ctrl_id); + mtk_thermal_init_bank(mt, i, mt->apmixed_phys_base, + mt->auxadc_phys_base, ctrl_id); platform_set_drvdata(pdev, mt); @@ -1041,11 +1088,80 @@ static int mtk_thermal_remove(struct platform_device *pdev) return 0; } +static int __maybe_unused mtk_thermal_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct mtk_thermal *mt = platform_get_drvdata(pdev); + int i, ret; + + for (i = 0; i < mt->conf->num_banks; i++) { + ret = mtk_thermal_disable_sensing(mt, i); + if (ret) + goto out; + } + + /* disable buffer */ + writel(readl(mt->apmixed_base + APMIXED_SYS_TS_CON1) | + APMIXED_SYS_TS_CON1_BUFFER_OFF, + mt->apmixed_base + APMIXED_SYS_TS_CON1); + + clk_disable_unprepare(mt->clk_peri_therm); + clk_disable_unprepare(mt->clk_auxadc); + + return 0; + +out: + dev_err(&pdev->dev, "Failed to wait until bus idle\n"); + + return ret; +} + +static int __maybe_unused mtk_thermal_resume(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct mtk_thermal *mt = platform_get_drvdata(pdev); + int i, ret, ctrl_id; + + ret = device_reset(&pdev->dev); + if (ret) + return ret; + + ret = clk_prepare_enable(mt->clk_auxadc); + if (ret) { + dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret); + goto err_disable_clk_auxadc; + } + + ret = clk_prepare_enable(mt->clk_peri_therm); + if (ret) { + dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret); + goto err_disable_clk_peri_therm; + } + + for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++) + for (i = 0; i < mt->conf->num_banks; i++) + mtk_thermal_init_bank(mt, i, mt->apmixed_phys_base, + mt->auxadc_phys_base, ctrl_id); + + return 0; + +err_disable_clk_peri_therm: + clk_disable_unprepare(mt->clk_peri_therm); +err_disable_clk_auxadc: + clk_disable_unprepare(mt->clk_auxadc); + + return ret; +} + +static SIMPLE_DEV_PM_OPS(mtk_thermal_pm_ops, + mtk_thermal_suspend, mtk_thermal_resume); + static struct platform_driver mtk_thermal_driver = { .probe = mtk_thermal_probe, .remove = mtk_thermal_remove, .driver = { .name = "mtk-thermal", + .pm = &mtk_thermal_pm_ops, .of_match_table = mtk_thermal_of_match, }, }; -- 1.9.1
