From: Michael Grzeschik <m.grzeschik@xxxxxxxxxxxxxx>
The patch adds the following interfaces according the SMARC Spec 1.1
[1] and provided schematics:
- SMARC SPI0/1
Note: Since Kontron still uses silicon revisions below 1.3 they have
add a spi-nor to implement Workaround #1 of erratum ERR006282.
- SMARC SDIO
- SMARC LCD
- SMARC HDMI
- SMARC Management pins
Note: Kontron don't route all of these pins to the i.MX6, some are
routed to the SoM CPLD.
- SMARC GPIO
- SMARC CSI Camera
Note: As specified in [1] the data lanes are shared to cover the
csi and the parallel case. The case depends on the baseboard so
muxing the data lanes is not part of this patch.
- SMARC I2S
- SMARC Watchdog
Note: The watchdog output pin is routed to the CPLD and the SMARC
header. The CPLD performs a reset after a 30s timeout so we
need to enable the watchdog per default.
- SMARC module eeprom
Due to the lack of hardware not all of these interfaces are tesetd.
[1] https://sget.org/standards/smarc
Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
---
v2:
- rename patch title
- squash patch 3-17
- drop fsl,spi-num-chipselects property
- make use of GPIO_ACTIVE_HIGH
- s/boot-flash/spi-flash/
- add phandles for spi-flash and eeprom so we can add partitions node
later on.
- spi-nor: reorder node properties
arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi | 12 +
arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi | 36 ++
arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi | 394 ++++++++++++++++++
3 files changed, 442 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi
create mode 100644 arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi b/arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi
new file mode 100644
index 000000000000..a864fdbd5f16
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2019 (C) Pengutronix, Marco Felsch <kernel@xxxxxxxxxxxxxx>
+ */
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-kontron-samx6i.dtsi"
+
+/ {
+ model = "Kontron SMARC sAMX6i Dual-Lite/Solo";
+ compatible = "kontron,imx6dl-samx6i", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi b/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
new file mode 100644
index 000000000000..2618eccfe50d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2019 (C) Pengutronix, Marco Felsch <kernel@xxxxxxxxxxxxxx>
+ */
+
+#include "imx6q.dtsi"
+#include "imx6qdl-kontron-samx6i.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Kontron SMARC sAMX6i Quad/Dual";
+ compatible = "kontron,imx6q-samx6i", "fsl,imx6q";
+};
+
+/* Quad/Dual SoMs have 3 chip-select signals */
+&ecspi4 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>,
+ <&gpio3 29 GPIO_ACTIVE_HIGH>,
+ <&gpio3 25 GPIO_ACTIVE_HIGH>;
+};
+
+&pinctrl_ecspi4 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+
+ /* SPI4_IMX_CS2# - connected to internal flash */
+ MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x1b0b0
+ /* SPI4_IMX_CS0# - connected to SMARC SPI0_CS0# */
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
+ /* SPI4_CS3# - connected to SMARC SPI0_CS1# */
+ MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x1b0b0
+ >;
+};
diff --git a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi b/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
index 12b12490792c..81c7ebb4b3fb 100644
--- a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
@@ -8,6 +8,7 @@
*/
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
/ {
reg_1p0v_s0: regulator-1p0v-s0 {
@@ -70,6 +71,28 @@
vin-supply = <®_smarc_suppy>;
};
+ reg_smarc_lcdbklt: regulator-smarc-lcdbklt {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdbklt_en>;
+ regulator-name = "LCD_BKLT_EN";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_smarc_lcdvdd: regulator-smarc-lcdvdd {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdvdd_en>;
+ regulator-name = "LCD_VDD_EN";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
reg_smarc_rtc: regulator-smarc-rtc {
compatible = "regulator-fixed";
regulator-name = "V_IN_RTC_BATT";
@@ -89,6 +112,41 @@
regulator-boot-on;
};
+ lcd: lcd {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd>;
+ status = "disabled";
+
+ port@0 {
+ reg = <0>;
+
+ lcd_in: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lcd_out: endpoint {
+ };
+ };
+ };
+
+ lcd_backlight: lcd-backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm4 0 5000000>;
+ pwm-names = "LCD_BKLT_PWM";
+
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <4>;
+
+ power-supply = <®_smarc_lcdbklt>;
+ status = "disabled";
+ };
+
i2c_intern: i2c-gpio-intern {
compatible = "i2c-gpio";
pinctrl-names = "default";
@@ -99,6 +157,76 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ i2c_lcd: i2c-gpio-lcd {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio_lcd>;
+ sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabld";
+ };
+
+ i2c_cam: i2c-gpio-cam {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio_cam>;
+ sda-gpios = <&gpio4 10 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabld";
+ };
+};
+
+/* I2S0, I2S1 */
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+
+ audmux_ssi1 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_TFSEL(MX51_AUDMUX_PORT3) |
+ IMX_AUDMUX_V2_PTCR_TCSEL(MX51_AUDMUX_PORT3) |
+ IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT3)
+ >;
+ };
+
+ audmux_adu3 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT3>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT1_SSI0)
+ >;
+ };
+
+ audmux_ssi2 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT2_SSI1>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_TFSEL(MX51_AUDMUX_PORT4) |
+ IMX_AUDMUX_V2_PTCR_TCSEL(MX51_AUDMUX_PORT4) |
+ IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT4)
+ >;
+ };
+
+ audmux_adu4 {
+ fsl,audmux-port = <MX51_AUDMUX_PORT4>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX51_AUDMUX_PORT2_SSI1)
+ >;
+ };
};
/* CAN0 */
@@ -113,6 +241,30 @@
pinctrl-0 = <&pinctrl_flexcan2>;
};
+/* SPI1 */
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>,
+ <&gpio2 27 GPIO_ACTIVE_HIGH>;
+};
+
+/* SPI0 */
+&ecspi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ cs-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>,
+ <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ /* default boot source: workaround #1 for errata ERR006282 */
+ smarc_flash: spi-flash@0 {
+ compatible = "winbond,w25q16dw", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
/* GBE */
&fec {
pinctrl-names = "default";
@@ -236,14 +388,79 @@
};
};
+/* I2C_GP */
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+};
+
+/* HDMI_CTRL */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+};
+
/* I2C_PM */
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ smarc_eeprom: eeprom@50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
};
&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mgmt_gpios &pinctrl_gpio>;
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+
+ MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x130b0
+ MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
+
+ /* AUDIO MCLK */
+ MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x000b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b0 /* CS0 */
+ MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0 /* CS1 */
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+
+ /* SPI_IMX_CS2# - connected to internal flash */
+ MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x1b0b0
+ /* SPI_IMX_CS0# - connected to SMARC SPI0_CS0# */
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
+ >;
+ };
+
pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
@@ -258,6 +475,23 @@
>;
};
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b0 /* GPIO0 / CAM0_PWR# */
+ MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x1b0b0 /* GPIO1 / CAM1_PWR# */
+ MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x1b0b0 /* GPIO2 / CAM0_RST# */
+ MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x1b0b0 /* GPIO3 / CAM1_RST# */
+ MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b0 /* GPIO4 / HDA_RST# */
+ MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b0 /* GPIO5 / PWM_OUT */
+ MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x1b0b0 /* GPIO6 / TACHIN */
+ MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b0 /* GPIO7 / PCAM_FLD */
+ MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x1b0b0 /* GPIO8 / CAN0_ERR# */
+ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x1b0b0 /* GPIO9 / CAN1_ERR# */
+ MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x1b0b0 /* GPIO10 */
+ MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x1b0b0 /* GPIO11 */
+ >;
+ };
+
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
@@ -280,6 +514,13 @@
>;
};
+ pinctrl_i2c_gpio_cam: i2c-gpiocamgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 /* SCL */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0 /* SDA */
+ >;
+ };
+
pinctrl_i2c_gpio_intern: i2c-gpiointerngrp {
fsl,pins = <
MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0 /* SCL */
@@ -287,6 +528,27 @@
>;
};
+ pinctrl_i2c_gpio_lcd: i2c-gpiolcdgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0 /* SCL */
+ MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b0 /* SDA */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
@@ -294,6 +556,72 @@
>;
};
+ pinctrl_lcd: lcdgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x100f1
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x100f1
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x100f1
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x100f1
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x100f1
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x100f1
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x100f1
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x100f1
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x100f1
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x100f1
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x100f1
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x100f1
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x100f1
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x100f1
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x100f1
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x100f1
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x100f1
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x100f1
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x100f1
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x100f1
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x100f1
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x100f1
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x100f1
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x100f1
+
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x100f1
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x100f1 /* DE */
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x100f1 /* HSYNC */
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x100f1 /* VSYNC */
+ >;
+ };
+
+ pinctrl_lcdbklt_en: lcdbkltengrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b1
+ >;
+ };
+
+ pinctrl_lcdvdd_en: lcdvddengrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
+ >;
+ };
+
+ pinctrl_mipi_csi: mipi-csigrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x000b0 /* CSI0/1 MCLK */
+ >;
+ };
+
+ pinctrl_mgmt_gpios: mgmt-gpiosgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1b0b0 /* LID# */
+ MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x1b0b0 /* SLEEP# */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 /* CHARGING# */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 /* CHARGER_PRSNT# */
+ MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x1b0b0 /* CARRIER_STBY# */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0 /* BATLOW# */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b0 /* TEST# */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 /* VDD_IO_SEL_D# */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x1b0b0 /* POWER_BTN# */
+ >;
+ };
+
pinctrl_pcie: pciegrp {
fsl,pins = <
MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x1b0b0 /* PCI_A_PRSNT# */
@@ -302,6 +630,12 @@
>;
};
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
@@ -343,6 +677,21 @@
>;
};
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x17059
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x1b0b0 /* CD */
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b0 /* WP */
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PWR_EN */
+ >;
+ };
+
pinctrl_usdhc4: usdhc4grp {
fsl,pins = <
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x17059
@@ -357,6 +706,17 @@
MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
>;
};
+
+ pinctrl_wdog1: wdog1rp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__WDOG1_B 0x1b0b0
+ >;
+ };
+};
+
+&mipi_csi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mipi_csi>;
};
&pcie {
@@ -366,6 +726,24 @@
reset-gpio = <&gpio3 13 GPIO_ACTIVE_HIGH>;
};
+/* LCD_BKLT_PWM */
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+};
+
+®_arm {
+ vin-supply = <®_v_core_s0>;
+};
+
+®_pu {
+ vin-supply = <®_vddsoc_s0>;
+};
+
+®_soc {
+ vin-supply = <®_vddsoc_s0>;
+};
+
/* SER0 */
&uart1 {
pinctrl-names = "default";
@@ -407,6 +785,15 @@
vbus-supply = <®_5p0v_s0>;
};
+/* SDIO */
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+};
+
/* SDMMC */
&usdhc4 {
/* Internal eMMC, optional on some boards */
@@ -419,3 +806,10 @@
vmmc-supply = <®_3p3v_s0>;
vqmmc-supply = <®_1p8v_s0>;
};
+
+&wdog1 {
+ /* CPLD is feeded by watchdog (hardwired) */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog1>;
+ status = "okay";
+};
--
2.20.1
