On Tue 11 Jun 09:08 PDT 2019, Bean Huo (beanhuo) wrote:
> Hi, Bjorn
> This HW reset is dedicated to QUALCOMM based platform case.
> how about adding a SW reset as to be default reset routine if platform doesn't support HW reset?
>
Can you please advice how I perform such software reset?
Regards,
Bjorn
> >-----Original Message-----
> >From: linux-scsi-owner@xxxxxxxxxxxxxxx <linux-scsi-owner@xxxxxxxxxxxxxxx>
> >On Behalf Of Bjorn Andersson
> >Sent: Saturday, June 8, 2019 7:05 AM
> >To: Rob Herring <robh+dt@xxxxxxxxxx>; Mark Rutland
> ><mark.rutland@xxxxxxx>; Alim Akhtar <alim.akhtar@xxxxxxxxxxx>; Avri
> >Altman <avri.altman@xxxxxxx>; Pedro Sousa
> ><pedrom.sousa@xxxxxxxxxxxx>; James E.J. Bottomley <jejb@xxxxxxxxxxxxx>;
> >Martin K. Petersen <martin.petersen@xxxxxxxxxx>
> >Cc: Andy Gross <agross@xxxxxxxxxx>; devicetree@xxxxxxxxxxxxxxx; linux-
> >kernel@xxxxxxxxxxxxxxx; linux-arm-msm@xxxxxxxxxxxxxxx; linux-
> >scsi@xxxxxxxxxxxxxxx
> >Subject: [EXT] [PATCH v3 2/3] scsi: ufs-qcom: Implement device_reset vops
> >
> >The UFS_RESET pin on Qualcomm SoCs are controlled by TLMM and exposed
> >through the GPIO framework. Acquire the device-reset GPIO and use this to
> >implement the device_reset vops, to allow resetting the attached memory.
> >
> >Based on downstream support implemented by Subhash Jadavani
> ><subhashj@xxxxxxxxxxxxxx>.
> >
> >Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> >---
> >
> >Changes since v2:
> >- Moved implementation to Qualcomm driver
> >
> > .../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 2 ++
> > drivers/scsi/ufs/ufs-qcom.c | 32 +++++++++++++++++++
> > drivers/scsi/ufs/ufs-qcom.h | 4 +++
> > 3 files changed, 38 insertions(+)
> >
> >diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >index a74720486ee2..d562d8b4919c 100644
> >--- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
> >@@ -54,6 +54,8 @@ Optional properties:
> > PHY reset from the UFS controller.
> > - resets : reset node register
> > - reset-names : describe reset node register, the "rst" corresponds to
> >reset the whole UFS IP.
> >+- device-reset-gpios : A phandle and gpio specifier denoting the GPIO
> >connected
> >+ to the RESET pin of the UFS memory device.
> >
> > Note: If above properties are not defined it can be assumed that the supply
> >regulators or clocks are always on.
> >diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c index
> >ea7219407309..efaf57ba618a 100644
> >--- a/drivers/scsi/ufs/ufs-qcom.c
> >+++ b/drivers/scsi/ufs/ufs-qcom.c
> >@@ -16,6 +16,7 @@
> > #include <linux/of.h>
> > #include <linux/platform_device.h>
> > #include <linux/phy/phy.h>
> >+#include <linux/gpio/consumer.h>
> > #include <linux/reset-controller.h>
> >
> > #include "ufshcd.h"
> >@@ -1141,6 +1142,15 @@ static int ufs_qcom_init(struct ufs_hba *hba)
> > goto out_variant_clear;
> > }
> >
> >+ host->device_reset = devm_gpiod_get_optional(dev, "device-reset",
> >+ GPIOD_OUT_HIGH);
> >+ if (IS_ERR(host->device_reset)) {
> >+ err = PTR_ERR(host->device_reset);
> >+ if (err != -EPROBE_DEFER)
> >+ dev_err(dev, "failed to acquire reset gpio: %d\n", err);
> >+ goto out_variant_clear;
> >+ }
> >+
> > err = ufs_qcom_bus_register(host);
> > if (err)
> > goto out_variant_clear;
> >@@ -1546,6 +1556,27 @@ static void ufs_qcom_dump_dbg_regs(struct
> >ufs_hba *hba)
> > usleep_range(1000, 1100);
> > }
> >
> >+/**
> >+ * ufs_qcom_device_reset() - toggle the (optional) device reset line
> >+ * @hba: per-adapter instance
> >+ *
> >+ * Toggles the (optional) reset line to reset the attached device.
> >+ */
> >+static void ufs_qcom_device_reset(struct ufs_hba *hba) {
> >+ struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> >+
> >+ /*
> >+ * The UFS device shall detect reset pulses of 1us, sleep for 10us to
> >+ * be on the safe side.
> >+ */
> >+ gpiod_set_value_cansleep(host->device_reset, 1);
> >+ usleep_range(10, 15);
> >+
> >+ gpiod_set_value_cansleep(host->device_reset, 0);
> >+ usleep_range(10, 15);
> >+}
> >+
> > /**
> > * struct ufs_hba_qcom_vops - UFS QCOM specific variant operations
> > *
> >@@ -1566,6 +1597,7 @@ static struct ufs_hba_variant_ops
> >ufs_hba_qcom_vops = {
> > .suspend = ufs_qcom_suspend,
> > .resume = ufs_qcom_resume,
> > .dbg_register_dump = ufs_qcom_dump_dbg_regs,
> >+ .device_reset = ufs_qcom_device_reset,
> > };
> >
> > /**
> >diff --git a/drivers/scsi/ufs/ufs-qcom.h b/drivers/scsi/ufs/ufs-qcom.h index
> >68a880185752..b96ffb6804e4 100644
> >--- a/drivers/scsi/ufs/ufs-qcom.h
> >+++ b/drivers/scsi/ufs/ufs-qcom.h
> >@@ -204,6 +204,8 @@ struct ufs_qcom_testbus {
> > u8 select_minor;
> > };
> >
> >+struct gpio_desc;
> >+
> > struct ufs_qcom_host {
> > /*
> > * Set this capability if host controller supports the QUniPro mode
> >@@ -241,6 +243,8 @@ struct ufs_qcom_host {
> > struct ufs_qcom_testbus testbus;
> >
> > struct reset_controller_dev rcdev;
> >+
> >+ struct gpio_desc *device_reset;
> > };
> >
> > static inline u32
> >--
> >2.18.0
>
