From: Claudiu Beznea <claudiu.beznea@xxxxxxxxxxxxx>
SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength and
at91_pinctrl_mux_ops::get_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.
Signed-off-by: Claudiu Beznea <claudiu.beznea@xxxxxxxxxxxxx>
---
drivers/pinctrl/pinctrl-at91.c | 32 ++++++++++++++++++++------------
1 file changed, 20 insertions(+), 12 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
index 3d49bbbcdbc7..31f06dafca2e 100644
--- a/drivers/pinctrl/pinctrl-at91.c
+++ b/drivers/pinctrl/pinctrl-at91.c
@@ -72,10 +72,15 @@ static int gpio_banks;
* DRIVE_STRENGTH_DEFAULT is just a placeholder to avoid changing the drive
* strength when there is no dt config for it.
*/
-#define DRIVE_STRENGTH_DEFAULT (0 << DRIVE_STRENGTH_SHIFT)
-#define DRIVE_STRENGTH_LOW (1 << DRIVE_STRENGTH_SHIFT)
-#define DRIVE_STRENGTH_MED (2 << DRIVE_STRENGTH_SHIFT)
-#define DRIVE_STRENGTH_HI (3 << DRIVE_STRENGTH_SHIFT)
+enum drive_strength_bit {
+ DRIVE_STRENGTH_BIT_DEF,
+ DRIVE_STRENGTH_BIT_LOW,
+ DRIVE_STRENGTH_BIT_MED,
+ DRIVE_STRENGTH_BIT_HI,
+};
+
+#define DRIVE_STRENGTH_BIT_MSK(name) (DRIVE_STRENGTH_BIT_##name << \
+ DRIVE_STRENGTH_SHIFT)
/**
* struct at91_pmx_func - describes AT91 pinmux functions
@@ -551,7 +556,7 @@ static unsigned at91_mux_sama5d3_get_drivestrength(void __iomem *pio,
/* SAMA5 strength is 1:1 with our defines,
* except 0 is equivalent to low per datasheet */
if (!tmp)
- tmp = DRIVE_STRENGTH_LOW;
+ tmp = DRIVE_STRENGTH_BIT_MSK(LOW);
return tmp;
}
@@ -564,7 +569,7 @@ static unsigned at91_mux_sam9x5_get_drivestrength(void __iomem *pio,
/* strength is inverse in SAM9x5s hardware with the pinctrl defines
* hardware: 0 = hi, 1 = med, 2 = low, 3 = rsvd */
- tmp = DRIVE_STRENGTH_HI - tmp;
+ tmp = DRIVE_STRENGTH_BIT_MSK(HI) - tmp;
return tmp;
}
@@ -600,7 +605,7 @@ static void at91_mux_sam9x5_set_drivestrength(void __iomem *pio, unsigned pin,
/* strength is inverse on SAM9x5s with our defines
* 0 = hi, 1 = med, 2 = low, 3 = rsvd */
- setting = DRIVE_STRENGTH_HI - setting;
+ setting = DRIVE_STRENGTH_BIT_MSK(HI) - setting;
set_drive_strength(pio + at91sam9x5_get_drive_register(pin), pin,
setting);
@@ -959,11 +964,11 @@ static int at91_pinconf_set(struct pinctrl_dev *pctldev,
} \
} while (0)
-#define DBG_SHOW_FLAG_MASKED(mask,flag) do { \
+#define DBG_SHOW_FLAG_MASKED(mask,flag,name) do { \
if ((config & mask) == flag) { \
if (num_conf) \
seq_puts(s, "|"); \
- seq_puts(s, #flag); \
+ seq_puts(s, #name); \
num_conf++; \
} \
} while (0)
@@ -981,9 +986,12 @@ static void at91_pinconf_dbg_show(struct pinctrl_dev *pctldev,
DBG_SHOW_FLAG(PULL_DOWN);
DBG_SHOW_FLAG(DIS_SCHMIT);
DBG_SHOW_FLAG(DEGLITCH);
- DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_LOW);
- DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_MED);
- DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_HI);
+ DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_BIT_MSK(LOW),
+ DRIVE_STRENGTH_LOW);
+ DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_BIT_MSK(MED),
+ DRIVE_STRENGTH_MED);
+ DBG_SHOW_FLAG_MASKED(DRIVE_STRENGTH, DRIVE_STRENGTH_BIT_MSK(HI),
+ DRIVE_STRENGTH_HI);
DBG_SHOW_FLAG(DEBOUNCE);
if (config & DEBOUNCE) {
val = config >> DEBOUNCE_VAL_SHIFT;
--
2.7.4
