Gru-Scarlet is a tablet device using ChomeOS, dual-dsi display
and Wacom touchscreen with stylus.
There exist two variants in the market using different displays
that are differentiated via their sku-id.
The bootloader on them also determines the correct devicetree to
load via the sku-id.
So add a common scarlet dtsi and two minimal board devicetrees
for the two display variants.
Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>
---
changes in v2:
- drop coreboot param override
- rebase against current master state so it will apply against 4.20-rc1
.../devicetree/bindings/arm/rockchip.txt | 34 +
arch/arm64/boot/dts/rockchip/Makefile | 2 +
.../dts/rockchip/rk3399-gru-scarlet-inx.dts | 33 +
.../dts/rockchip/rk3399-gru-scarlet-kd.dts | 33 +
.../boot/dts/rockchip/rk3399-gru-scarlet.dtsi | 594 ++++++++++++++++++
5 files changed, 696 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-kd.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 0cc71236d639..7ce7382fedd8 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -152,6 +152,40 @@ Rockchip platforms device tree bindings
- compatible = "google,veyron-pinky-rev2", "google,veyron-pinky",
"google,veyron", "rockchip,rk3288";
+- Google Scarlet - with display from Kingdisplay
+ Required root node properties:
+ - compatible = "google,scarlet-rev15-sku7", "google,scarlet-rev15",
+ "google,scarlet-rev14-sku7", "google,scarlet-rev14",
+ "google,scarlet-rev13-sku7", "google,scarlet-rev13",
+ "google,scarlet-rev12-sku7", "google,scarlet-rev12",
+ "google,scarlet-rev11-sku7", "google,scarlet-rev11",
+ "google,scarlet-rev10-sku7", "google,scarlet-rev10",
+ "google,scarlet-rev9-sku7", "google,scarlet-rev9",
+ "google,scarlet-rev8-sku7", "google,scarlet-rev8",
+ "google,scarlet-rev7-sku7", "google,scarlet-rev7",
+ "google,scarlet-rev6-sku7", "google,scarlet-rev6",
+ "google,scarlet-rev5-sku7", "google,scarlet-rev5",
+ "google,scarlet-rev4-sku7", "google,scarlet-rev4",
+ "google,scarlet-rev3-sku7", "google,scarlet-rev3",
+ "google,scarlet", "google,gru", "rockchip,rk3399";
+
+- Google Scarlet - with display from Innolux
+ Required root node properties:
+ - compatible = "google,scarlet-rev15-sku6", "google,scarlet-rev15",
+ "google,scarlet-rev14-sku6", "google,scarlet-rev14",
+ "google,scarlet-rev13-sku6", "google,scarlet-rev13",
+ "google,scarlet-rev12-sku6", "google,scarlet-rev12",
+ "google,scarlet-rev11-sku6", "google,scarlet-rev11",
+ "google,scarlet-rev10-sku6", "google,scarlet-rev10",
+ "google,scarlet-rev9-sku6", "google,scarlet-rev9",
+ "google,scarlet-rev8-sku6", "google,scarlet-rev8",
+ "google,scarlet-rev7-sku6", "google,scarlet-rev7",
+ "google,scarlet-rev6-sku6", "google,scarlet-rev6",
+ "google,scarlet-rev5-sku6", "google,scarlet-rev5",
+ "google,scarlet-rev4-sku6", "google,scarlet-rev4",
+ "google,scarlet", "google,gru", "rockchip,rk3399";
+
+
- Google Speedy (Asus C201 Chromebook):
Required root node properties:
- compatible = "google,veyron-speedy-rev9", "google,veyron-speedy-rev8",
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 49042c477870..de0c406c20cc 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -14,6 +14,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ficus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-bob.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-scarlet-inx.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-scarlet-kd.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock960.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts
new file mode 100644
index 000000000000..2d721a974790
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Gru-Scarlet Rev4+ (SKU-6/Innolux) board device tree source
+ *
+ * Copyright 2018 Google, Inc
+ */
+
+/dts-v1/;
+
+#include "rk3399-gru-scarlet.dtsi"
+
+/ {
+ model = "Google Scarlet";
+ compatible = "google,scarlet-rev15-sku6", "google,scarlet-rev15",
+ "google,scarlet-rev14-sku6", "google,scarlet-rev14",
+ "google,scarlet-rev13-sku6", "google,scarlet-rev13",
+ "google,scarlet-rev12-sku6", "google,scarlet-rev12",
+ "google,scarlet-rev11-sku6", "google,scarlet-rev11",
+ "google,scarlet-rev10-sku6", "google,scarlet-rev10",
+ "google,scarlet-rev9-sku6", "google,scarlet-rev9",
+ "google,scarlet-rev8-sku6", "google,scarlet-rev8",
+ "google,scarlet-rev7-sku6", "google,scarlet-rev7",
+ "google,scarlet-rev6-sku6", "google,scarlet-rev6",
+ "google,scarlet-rev5-sku6", "google,scarlet-rev5",
+ "google,scarlet-rev4-sku6", "google,scarlet-rev4",
+ "google,scarlet", "google,gru", "rockchip,rk3399";
+};
+
+&mipi_panel {
+ compatible = "innolux,p097pfg";
+ avdd-supply = <&ppvarp_lcd>;
+ avee-supply = <&ppvarn_lcd>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-kd.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-kd.dts
new file mode 100644
index 000000000000..e49a194aaa0f
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-kd.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Gru-Scarlet Rev3+ (SKU-7/Kingdisplay) board device tree source
+ *
+ * Copyright 2018 Google, Inc
+ */
+
+/dts-v1/;
+
+#include "rk3399-gru-scarlet.dtsi"
+
+/ {
+ model = "Google Scarlet";
+ compatible = "google,scarlet-rev15-sku7", "google,scarlet-rev15",
+ "google,scarlet-rev14-sku7", "google,scarlet-rev14",
+ "google,scarlet-rev13-sku7", "google,scarlet-rev13",
+ "google,scarlet-rev12-sku7", "google,scarlet-rev12",
+ "google,scarlet-rev11-sku7", "google,scarlet-rev11",
+ "google,scarlet-rev10-sku7", "google,scarlet-rev10",
+ "google,scarlet-rev9-sku7", "google,scarlet-rev9",
+ "google,scarlet-rev8-sku7", "google,scarlet-rev8",
+ "google,scarlet-rev7-sku7", "google,scarlet-rev7",
+ "google,scarlet-rev6-sku7", "google,scarlet-rev6",
+ "google,scarlet-rev5-sku7", "google,scarlet-rev5",
+ "google,scarlet-rev4-sku7", "google,scarlet-rev4",
+ "google,scarlet-rev3-sku7", "google,scarlet-rev3",
+ "google,scarlet", "google,gru", "rockchip,rk3399";
+};
+
+&mipi_panel {
+ compatible = "kingdisplay,kd097d04";
+ power-supply = <&pp3300_s0>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
new file mode 100644
index 000000000000..fc50b3ef758c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
@@ -0,0 +1,594 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Gru-scarlet board device tree source
+ *
+ * Copyright 2018 Google, Inc
+ */
+
+#include "rk3399-gru.dtsi"
+
+/{
+ /* Power tree */
+
+ /* ppvar_sys children, sorted by name */
+ pp1250_s3: pp1250-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1250_s3";
+
+ /* EC turns on w/ pp1250_s3_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp1250_cam: pp1250-dvdd {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1250_dvdd";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pp1250_cam_en>;
+
+ enable-active-high;
+ gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+
+ /* 740us delay from gpio output high to pp1250 stable,
+ * rounding up to 1ms for safety.
+ */
+ startup-delay-us = <1000>;
+ vin-supply = <&pp1250_s3>;
+ };
+
+ pp900_s0: pp900-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp900_s0";
+
+ /* EC turns on w/ pp900_s0_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ ppvarn_lcd: ppvarn-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvarn_lcd";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ppvarn_lcd_en>;
+
+ enable-active-high;
+ gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&ppvar_sys>;
+ };
+
+ ppvarp_lcd: ppvarp-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvarp_lcd";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ppvarp_lcd_en>;
+
+ enable-active-high;
+ gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&ppvar_sys>;
+ };
+
+ /* pp1800 children, sorted by name */
+ pp900_s3: pp900-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp900_s3";
+
+ /* EC turns on w/ pp900_s3_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ vin-supply = <&pp1800>;
+ };
+
+ /* EC turns on pp1800_s3_en */
+ pp1800_s3: pp1800 {
+ };
+
+ /* pp3300 children, sorted by name */
+ pp2800_cam: pp2800-avdd {
+ compatible = "regulator-fixed";
+ regulator-name = "pp2800_avdd";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pp2800_cam_en>;
+
+ enable-active-high;
+ gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <100>;
+ vin-supply = <&pp3300>;
+ };
+
+ /* EC turns on pp3300_s0_en */
+ pp3300_s0: pp3300 {
+ };
+
+ /* EC turns on pp3300_s3_en */
+ pp3300_s3: pp3300 {
+ };
+
+ /*
+ * See b/66922012
+ *
+ * This is a hack to make sure the Bluetooth part of the QCA6174A
+ * is reset at boot by toggling BT_EN. At boot BT_EN is first set
+ * to low when the bt_3v3 regulator is registered (in disabled
+ * state). The fake regulator is configured as a supply of the
+ * wlan_3v3 regulator below. When wlan_3v3 is enabled early in
+ * the boot process it also enables its supply regulator bt_3v3,
+ * which changes BT_EN to high.
+ */
+ bt_3v3: bt-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "bt_3v3";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en_1v8_l>;
+
+ enable-active-high;
+ gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&pp3300_s3>;
+ };
+
+ wlan_3v3: wlan-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan_3v3";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_pd_1v8_l>;
+
+ /*
+ * The WL_EN pin is driven low when the regulator is
+ * registered, and transitions to high when the PCIe bus
+ * is powered up.
+ */
+ enable-active-high;
+ gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+
+ /*
+ * Require minimum 10ms from power-on (e.g., PD#) to init PCIe.
+ * TODO (b/64444991): how long to assert PD#?
+ */
+ regulator-enable-ramp-delay = <10000>;
+ /* See bt_3v3 hack above */
+ vin-supply = <&bt_3v3>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ enable-gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en>;
+ pwms = <&pwm1 0 1000000 0>;
+ pwm-delay-us = <10000>;
+ };
+
+ dmic: dmic {
+ compatible = "dmic-codec";
+ dmicen-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dmic_en>;
+ wakeup-delay-ms = <250>;
+ };
+};
+
+/* pp900_s0 aliases */
+pp900_ddrpll_ap: &pp900_s0 {
+};
+pp900_pcie: &pp900_s0 {
+};
+pp900_usb: &pp900_s0 {
+};
+
+/* pp900_s3 aliases */
+pp900_emmcpll: &pp900_s3 {
+};
+
+/* EC turns on; alias for pp1800_s0 */
+pp1800_pcie: &pp1800_s0 {
+};
+
+/* On scarlet PPVAR(big_cpu, lit_cpu, gpu) need to adjust voltage ranges */
+&ppvar_bigcpu {
+ ctrl-voltage-range = <800074 1299226>;
+ regulator-min-microvolt = <800074>;
+ regulator-max-microvolt = <1299226>;
+};
+
+&ppvar_bigcpu_pwm {
+ /* On scarlet ppvar big cpu use pwm3 */
+ pwms = <&pwm3 0 3337 0>;
+ regulator-min-microvolt = <800074>;
+ regulator-max-microvolt = <1299226>;
+};
+
+&ppvar_litcpu {
+ ctrl-voltage-range = <802122 1199620>;
+ regulator-min-microvolt = <802122>;
+ regulator-max-microvolt = <1199620>;
+};
+
+&ppvar_litcpu_pwm {
+ regulator-min-microvolt = <802122>;
+ regulator-max-microvolt = <1199620>;
+};
+
+&ppvar_gpu {
+ ctrl-voltage-range = <799600 1099600>;
+ regulator-min-microvolt = <799600>;
+ regulator-max-microvolt = <1099600>;
+};
+
+&ppvar_gpu_pwm {
+ regulator-min-microvolt = <799600>;
+ regulator-max-microvolt = <1099600>;
+};
+
+&ppvar_sd_card_io {
+ states = <1800000 0x0 3300000 0x1>;
+ regulator-max-microvolt = <3300000>;
+};
+
+&pp3000_sd_slot {
+ vin-supply = <&pp3300>;
+};
+
+ap_i2c_dig: &i2c2 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times. */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+
+ digitizer: digitizer@9 {
+ compatible = "hid-over-i2c";
+ reg = <0x9>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ hid-descr-addr = <0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pen_int_odl &pen_reset_l>;
+ };
+};
+
+&ap_i2c_ts {
+ touchscreen: touchscreen@10 {
+ compatible = "elan,ekth3500";
+ reg = <0x10>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_int_l &touch_reset_l>;
+ reset-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+ };
+};
+
+camera: &i2c7 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times; TODO: measure */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+
+ /* 24M mclk is shared between world and user cameras */
+ pinctrl-0 = <&i2c7_xfer &test_clkout1>;
+};
+
+&cdn_dp {
+ extcon = <&usbc_extcon0>;
+ phys = <&tcphy0_dp>;
+};
+
+&cpu_alert0 {
+ temperature = <66000>;
+};
+
+&cpu_alert1 {
+ temperature = <71000>;
+};
+
+&cros_ec {
+ interrupt-parent = <&gpio1>;
+ interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&cru {
+ assigned-clocks =
+ <&cru PLL_GPLL>, <&cru PLL_CPLL>,
+ <&cru PLL_NPLL>,
+ <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
+ <&cru PCLK_PERIHP>,
+ <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
+ <&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
+ <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
+ <&cru ACLK_VIO>,
+ <&cru ACLK_GIC_PRE>,
+ <&cru PCLK_DDR>,
+ <&cru ACLK_HDCP>;
+ assigned-clock-rates =
+ <600000000>, <1600000000>,
+ <1000000000>,
+ <150000000>, <75000000>,
+ <37500000>,
+ <100000000>, <100000000>,
+ <50000000>, <800000000>,
+ <100000000>, <50000000>,
+ <400000000>,
+ <200000000>,
+ <200000000>,
+ <400000000>;
+};
+
+&gpio_keys {
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l>, <&pen_eject_odl>;
+
+ pen-insert {
+ label = "Pen Insert";
+ /* Insert = low, eject = high */
+ gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ linux,code = <SW_PEN_INSERTED>;
+ linux,input-type = <EV_SW>;
+ wakeup-source;
+ };
+};
+
+&i2c_tunnel {
+ google,remote-bus = <0>;
+};
+
+&io_domains {
+ bt656-supply = <&pp1800_s0>; /* APIO2_VDD; 2a 2b */
+ audio-supply = <&pp1800_s0>; /* APIO5_VDD; 3d 4a */
+ gpio1830-supply = <&pp1800_s0>; /* APIO4_VDD; 4c 4d */
+};
+
+&max98357a {
+ sdmode-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+};
+
+&mipi_dsi {
+ status = "okay";
+ clock-master;
+
+ ports {
+ mipi_out: port@1 {
+ reg = <1>;
+
+ mipi_out_panel: endpoint {
+ remote-endpoint = <&mipi_in_panel>;
+ };
+ };
+ };
+
+ mipi_panel: panel@0 {
+ /* 2 different panels are used, compatibles are in dts files */
+ reg = <0>;
+ backlight = <&backlight>;
+ enable-gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&display_rst_l>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mipi_in_panel: endpoint {
+ remote-endpoint = <&mipi_out_panel>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ mipi1_in_panel: endpoint@1 {
+ remote-endpoint = <&mipi1_out_panel>;
+ };
+ };
+ };
+ };
+};
+
+&mipi_dsi1 {
+ status = "okay";
+
+ ports {
+ mipi1_out: port@1 {
+ reg = <1>;
+
+ mipi1_out_panel: endpoint {
+ remote-endpoint = <&mipi1_in_panel>;
+ };
+ };
+ };
+};
+
+&pcie0 {
+ ep-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+
+ /* PERST# asserted in S3 */
+ pcie-reset-suspend = <1>;
+
+ vpcie3v3-supply = <&wlan_3v3>;
+ vpcie1v8-supply = <&pp1800_pcie>;
+};
+
+&sdmmc {
+ cd-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+};
+
+&sound {
+ rockchip,codec = <&max98357a &dmic &codec &cdn_dp>;
+};
+
+&spi2 {
+ status = "okay";
+};
+
+&wake_on_bt {
+ gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+};
+
+/* PINCTRL OVERRIDES */
+&ec_ap_int_l {
+ rockchip,pins = <1 18 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&ap_fw_wp {
+ rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_pull_none>;
+};
+
+&bl_en {
+ rockchip,pins = <4 21 RK_FUNC_GPIO &pcfg_pull_none>;
+};
+
+&bt_host_wake_l {
+ rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&ec_ap_int_l {
+ rockchip,pins = <1 18 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&headset_int_l {
+ rockchip,pins = <1 23 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&i2s0_8ch_bus {
+ rockchip,pins =
+ <3 24 RK_FUNC_1 &pcfg_pull_none_6ma>,
+ <3 25 RK_FUNC_1 &pcfg_pull_none_6ma>,
+ <3 26 RK_FUNC_1 &pcfg_pull_none_6ma>,
+ <3 27 RK_FUNC_1 &pcfg_pull_none_6ma>,
+ <3 31 RK_FUNC_1 &pcfg_pull_none_6ma>,
+ <4 0 RK_FUNC_1 &pcfg_pull_none_6ma>;
+};
+
+/* there is no external pull up, so need to set this pin pull up */
+&sdmmc_cd_gpio {
+ rockchip,pins = <1 11 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&sd_pwr_1800_sel {
+ rockchip,pins = <2 28 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&sdmode_en {
+ rockchip,pins = <0 2 RK_FUNC_GPIO &pcfg_pull_down>;
+};
+
+&touch_reset_l {
+ rockchip,pins = <0 10 RK_FUNC_GPIO &pcfg_pull_down>;
+};
+
+&touch_int_l {
+ rockchip,pins = <1 4 RK_FUNC_GPIO &pcfg_pull_down>;
+};
+
+&pinctrl {
+ pinctrl-0 = <
+ &ap_pwroff /* AP will auto-assert this when in S3 */
+ &clk_32k /* This pin is always 32k on gru boards */
+ &wlan_rf_kill_1v8_l
+ >;
+
+ pcfg_pull_none_6ma: pcfg-pull-none-6ma {
+ bias-disable;
+ drive-strength = <6>;
+ };
+
+ camera {
+ pp1250_cam_en: pp1250-dvdd {
+ rockchip,pins = <2 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pp2800_cam_en: pp2800-avdd {
+ rockchip,pins = <2 24 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ ucam_rst: ucam_rst {
+ rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wcam_rst: wcam_rst {
+ rockchip,pins = <2 5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ digitizer {
+ pen_int_odl: pen-int-odl {
+ rockchip,pins = <1 0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ pen_reset_l: pen-reset-l {
+ rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ discrete-regulators {
+ display_rst_l: display-rst-l {
+ rockchip,pins = <4 25 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ ppvarp_lcd_en: ppvarp-lcd-en {
+ rockchip,pins = <4 27 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ ppvarn_lcd_en: ppvarn-lcd-en {
+ rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ dmic {
+ dmic_en: dmic-en {
+ rockchip,pins = <4 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pen {
+ pen_eject_odl: pen-eject-odl {
+ rockchip,pins = <1 1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ tpm {
+ h1_int_od_l: h1-int-od-l {
+ rockchip,pins = <1 17 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&wifi {
+ bt_en_1v8_l: bt-en-1v8-l {
+ rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wlan_pd_1v8_l: wlan-pd-1v8-l {
+ rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ /* Default pull-up, but just to be clear */
+ wlan_rf_kill_1v8_l: wlan-rf-kill-1v8-l {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ wifi_perst_l: wifi-perst-l {
+ rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wlan_host_wake_l: wlan-host-wake-l {
+ rockchip,pins = <1 3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+};
--
2.18.0
