RE: [PATCH v3] gpio: dwapb: Add support for 1 interrupt per port A GPIO

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Hoan

On 18 April 2018 08:03 Hoan Tran wrote:
> On Fri, Apr 13, 2018 at 9:47 AM, Phil Edworthy wrote:
> > On 13 April 2018 17:37 Hoan Tran wrote:
> >> On Fri, Apr 13, 2018 at 1:51 AM, Phil Edworthy wrote:
> >> > The DesignWare GPIO IP can be configured for either 1 interrupt or
> >> > 1 per GPIO in port A, but the driver currently only supports 1 interrupt.
> >> > See the DesignWare DW_apb_gpio Databook description of the
> >> > 'GPIO_INTR_IO' parameter.
> >> >
> >> > This change allows the driver to work with up to 32 interrupts, it
> >> > will get as many interrupts as specified in the DT 'interrupts' property.
> >> > It doesn't do anything clever with the different interrupts, it
> >> > just calls the same handler used for single interrupt hardware.
> >> >
> >> > Signed-off-by: Phil Edworthy <phil.edworthy@xxxxxxxxxxx>
> >> > ---
> >> > One point to mention is that I have made it possible for users to
> >> > have unconncted interrupts by specifying holes in the list of interrupts.
> >> > This is done by supporting the interrupts-extended DT prop.
> >> > However, I have no use for this and had to hack some test case for this.
> >> > Perhaps the driver should support 1 interrupt or all GPIOa as interrupts?
> >> >
> >> > v3:
> >> >  - Rolled mfd: intel_quark_i2c_gpio fix into this patch to avoid
> >> > bisect problems
> >> > v2:
> >> >  - Replaced interrupt-mask DT prop with support for the interrupts-
> >> extended
> >> >    prop. This means replacing the call to irq_of_parse_and_map() with
> calls
> >> >    to of_irq_parse_one() and irq_create_of_mapping().
> >> >
> >> > Note: There are a few *code* lines over 80 chars, but this is just
> guidance,
> >> >    right? Especially as there are already some lines over 80 chars.
> >> > ---
> > [snip]
> >
> >> > -               if (has_acpi_companion(dev) && pp->idx == 0)
> >> > -                       pp->irq = platform_get_irq(to_platform_device(dev), 0);
> >> > +               if (has_acpi_companion(dev) && pp->idx == 0) {
> >> > +                       pp->irq[0] = platform_get_irq(to_platform_device(dev),
> 0);
> >> > +                       if (pp->irq[0])
> >> > +                               pp->has_irq = true;
> >> > +               }
> >>
> >> It doesn't work for ACPI. Could you do the same logic for ACPI?
> > I don’t have access to any device that was baked (i.e. fabbed) with
> > multiple output interrupts from the Synopsys GPIO blocks and use ACPI.
> > I don't know if any such device exists.
> 
> Below code is tested on X-Gene system which supports 1 interrupt per GPIO
> on Port A. You can update it into your patch.
> 
> -               if (has_acpi_companion(dev) && pp->idx == 0)
> -                       pp->irq = platform_get_irq(to_platform_device(dev), 0);
> +               if (has_acpi_companion(dev) && pp->idx == 0) {
> +                       unsigned int j;
> +                       for (j = 0; j < pp->ngpio; j++) {
> +                               pp->irq[j] =
> platform_get_irq(to_platform_device(dev), j);
> +                               if (pp->irq[j])
> +                                       pp->has_irq = true;
> +                       }
> +               }
Since I've already got some reviewed-by and acks for v4, I'll leave it to Linus
to decide if he wants me to roll your changes into this patch or for you to
submit a separate patch.

Thanks
Phil


> >> >                 pp->irq_shared  = false;
> >> >                 pp->gpio_base   = -1;
> >> > diff --git a/drivers/mfd/intel_quark_i2c_gpio.c
> >> > b/drivers/mfd/intel_quark_i2c_gpio.c
> >> > index 90e35de..5bddb84 100644
> >> > --- a/drivers/mfd/intel_quark_i2c_gpio.c
> >> > +++ b/drivers/mfd/intel_quark_i2c_gpio.c
> >> > @@ -233,7 +233,8 @@ static int intel_quark_gpio_setup(struct
> >> > pci_dev
> >> *pdev, struct mfd_cell *cell)
> >> >         pdata->properties->idx          = 0;
> >> >         pdata->properties->ngpio        = INTEL_QUARK_MFD_NGPIO;
> >> >         pdata->properties->gpio_base    =
> INTEL_QUARK_MFD_GPIO_BASE;
> >> > -       pdata->properties->irq          = pdev->irq;
> >> > +       pdata->properties->irq[0]       = pdev->irq;
> >> > +       pdata->properties->has_irq      = true;
> >> >         pdata->properties->irq_shared   = true;
> >> >
> >> >         cell->platform_data = pdata; diff --git
> >> > a/include/linux/platform_data/gpio-dwapb.h
> >> > b/include/linux/platform_data/gpio-dwapb.h
> >> > index 2dc7f4a..5a52d69 100644
> >> > --- a/include/linux/platform_data/gpio-dwapb.h
> >> > +++ b/include/linux/platform_data/gpio-dwapb.h
> >> > @@ -19,7 +19,8 @@ struct dwapb_port_property {
> >> >         unsigned int    idx;
> >> >         unsigned int    ngpio;
> >> >         unsigned int    gpio_base;
> >> > -       unsigned int    irq;
> >> > +       unsigned int    irq[32];
> >> > +       bool            has_irq;
> >> >         bool            irq_shared;
> >> >  };
> >> >
> >> > --
> >> > 2.7.4
> >> >
��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux