Hi Jacopo,
On Tue, Jan 16, 2018 at 10:44:53PM +0100, Jacopo Mondi wrote:
> Add bindings documentation for Renesas Capture Engine Unit (CEU).
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Acked-by: Hans Verkuil <hans.verkuil@xxxxxxxxx>
> ---
> .../devicetree/bindings/media/renesas,ceu.txt | 81 ++++++++++++++++++++++
> 1 file changed, 81 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt
>
> diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> new file mode 100644
> index 0000000..590ee27
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> @@ -0,0 +1,81 @@
> +Renesas Capture Engine Unit (CEU)
> +----------------------------------------------
> +
> +The Capture Engine Unit is the image capture interface found in the Renesas
> +SH Mobile and RZ SoCs.
> +
> +The interface supports a single parallel input with data bus width of 8 or 16
> +bits.
> +
> +Required properties:
> +- compatible: Shall be "renesas,r7s72100-ceu" for CEU units found in RZ/A1-H
> + and RZ/A1-M SoCs.
> +- reg: Registers address base and size.
> +- interrupts: The interrupt specifier.
> +
> +The CEU supports a single parallel input and should contain a single 'port'
> +subnode with a single 'endpoint'. Connection to input devices are modeled
> +according to the video interfaces OF bindings specified in:
> +Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Optional endpoint properties applicable to parallel input bus described in
> +the above mentioned "video-interfaces.txt" file are supported.
> +
> +- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> + If property is not present, default is active high.
> +- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> + If property is not present, default is active high.
Does the hardware support Bt.656? If it does, you need to tell the
difference between the parallel interface with default sync polarity and
Bt.656 interfaces. With the above it's ambiguous.
> +
> +Example:
> +
> +The example describes the connection between the Capture Engine Unit and an
> +OV7670 image sensor connected to i2c1 interface.
> +
> +ceu: ceu@e8210000 {
> + reg = <0xe8210000 0x209c>;
> + compatible = "renesas,r7s72100-ceu";
> + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&vio_pins>;
> +
> + status = "okay";
> +
> + port {
> + ceu_in: endpoint {
> + remote-endpoint = <&ov7670_out>;
> +
> + hsync-active = <1>;
> + vsync-active = <0>;
> + };
> + };
> +};
> +
> +i2c1: i2c@fcfee400 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> +
> + status = "okay";
> +
> + clock-frequency = <100000>;
> +
> + ov7670: camera@21 {
> + compatible = "ovti,ov7670";
> + reg = <0x21>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&vio_pins>;
> +
> + reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
> + powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + ov7670_out: endpoint {
> + remote-endpoint = <&ceu_in>;
> +
> + hsync-active = <1>;
> + vsync-active = <0>;
> + };
> + };
> + };
> +};
> --
> 2.7.4
>
--
Sakari Ailus
e-mail: sakari.ailus@xxxxxx
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
