Hi Sakari,
it's the second series this week where I fail to handle BT.656
properly, sorry about this :)
On Wed, Jan 17, 2018 at 09:59:59AM +0200, Sakari Ailus wrote:
> Hi Jacopo,
>
> On Tue, Jan 16, 2018 at 10:44:53PM +0100, Jacopo Mondi wrote:
> > Add bindings documentation for Renesas Capture Engine Unit (CEU).
> >
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > Acked-by: Hans Verkuil <hans.verkuil@xxxxxxxxx>
> > ---
> > .../devicetree/bindings/media/renesas,ceu.txt | 81 ++++++++++++++++++++++
> > 1 file changed, 81 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> > new file mode 100644
> > index 0000000..590ee27
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> > @@ -0,0 +1,81 @@
> > +Renesas Capture Engine Unit (CEU)
> > +----------------------------------------------
> > +
> > +The Capture Engine Unit is the image capture interface found in the Renesas
> > +SH Mobile and RZ SoCs.
> > +
> > +The interface supports a single parallel input with data bus width of 8 or 16
> > +bits.
> > +
> > +Required properties:
> > +- compatible: Shall be "renesas,r7s72100-ceu" for CEU units found in RZ/A1-H
> > + and RZ/A1-M SoCs.
> > +- reg: Registers address base and size.
> > +- interrupts: The interrupt specifier.
> > +
> > +The CEU supports a single parallel input and should contain a single 'port'
> > +subnode with a single 'endpoint'. Connection to input devices are modeled
> > +according to the video interfaces OF bindings specified in:
> > +Documentation/devicetree/bindings/media/video-interfaces.txt
> > +
> > +Optional endpoint properties applicable to parallel input bus described in
> > +the above mentioned "video-interfaces.txt" file are supported.
> > +
> > +- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> > + If property is not present, default is active high.
> > +- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> > + If property is not present, default is active high.
>
> Does the hardware support Bt.656? If it does, you need to tell the
> difference between the parallel interface with default sync polarity and
> Bt.656 interfaces. With the above it's ambiguous.
No, it does not support BT.656.
I'm listing them as -required- endpoint properties. If they are not
specified the drivers fails during probe:
renesas-ceu e8210000.ceu: Only parallel input supported.
Thanks
j
>
> > +
> > +Example:
> > +
> > +The example describes the connection between the Capture Engine Unit and an
> > +OV7670 image sensor connected to i2c1 interface.
> > +
> > +ceu: ceu@e8210000 {
> > + reg = <0xe8210000 0x209c>;
> > + compatible = "renesas,r7s72100-ceu";
> > + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vio_pins>;
> > +
> > + status = "okay";
> > +
> > + port {
> > + ceu_in: endpoint {
> > + remote-endpoint = <&ov7670_out>;
> > +
> > + hsync-active = <1>;
> > + vsync-active = <0>;
> > + };
> > + };
> > +};
> > +
> > +i2c1: i2c@fcfee400 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c1_pins>;
> > +
> > + status = "okay";
> > +
> > + clock-frequency = <100000>;
> > +
> > + ov7670: camera@21 {
> > + compatible = "ovti,ov7670";
> > + reg = <0x21>;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vio_pins>;
> > +
> > + reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
> > + powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
> > +
> > + port {
> > + ov7670_out: endpoint {
> > + remote-endpoint = <&ceu_in>;
> > +
> > + hsync-active = <1>;
> > + vsync-active = <0>;
> > + };
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
>
> --
> Sakari Ailus
> e-mail: sakari.ailus@xxxxxx
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
