On Wed, Dec 27, 2017 at 09:27:23AM -0700, Karthikeyan Ramasubramanian wrote:
> Add device tree binding support for I2C Controller in GENI based
> QUP Wrapper.
>
> Signed-off-by: Sagar Dharia <sdharia@xxxxxxxxxxxxxx>
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/i2c/i2c-qcom-geni.txt | 39 ++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
>
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt b/Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
> new file mode 100644
> index 0000000..d2fa9ce
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
> @@ -0,0 +1,39 @@
> +Qualcomm Technologies Inc. GENI based I2C Controller driver
> +
> +Required properties:
> + - compatible: Should be:
> + * "qcom,i2c-geni.
Only 1 version?
> + - reg: Should contain QUP register address and length.
> + - interrupts: Should contain I2C interrupt.
> + - clocks: Serial engine core clock, and AHB clocks needed by the device.
Are there really clocks for a firmware based device or these are just
clocks in the parent serial engine?
> + - pinctrl-names/pinctrl-0/1: The GPIOs assigned to this core. The names
> + should be "active" and "sleep" for the pin confuguration when core is active
> + or when entering sleep state.
> + - #address-cells: Should be <1> Address cells for i2c device address
> + - #size-cells: Should be <0> as i2c addresses have no size component
> + - qcom,wrapper-core: Wrapper QUP core containing this I2C controller.
Probably these devices should be child nodes of the QUP core node.
> +
> +Optional property:
> + - qcom,clk-freq-out : Desired I2C bus clock frequency in Hz.
> + When missing default to 400000Hz.
There's a standard property for this.
> +
> +Child nodes should conform to i2c bus binding.
> +
> +Example:
> +
> +i2c@a94000 {
> + compatible = "qcom,i2c-geni";
> + reg = <0xa94000 0x4000>;
> + interrupts = <GIC_SPI 358 0>;
> + clock-names = "se-clk", "m-ahb", "s-ahb";
> + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S5_CLK>,
> + <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> + <&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_1_i2c_5_active>;
> + pinctrl-1 = <&qup_1_i2c_5_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + qcom,wrapper-core = <&qup_0>;
> + qcom,clk-freq-out = <400000>;
> +};
> --
> Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
