On Wed, Nov 22, 2017 at 08:37:04PM -0800, Tim Harvey wrote: > On Tue, Nov 21, 2017 at 11:36 PM, Sakari Ailus <sakari.ailus@xxxxxx> wrote: > > Hi Tim, > > > > On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote: > >> Cc: Rob Herring <robh@xxxxxxxxxx> > >> Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx> > >> --- > >> v3: > >> - fix typo > >> > >> v2: > >> - add vendor prefix and remove _ from vidout-portcfg > >> - remove _ from labels > >> - remove max-pixel-rate property > >> - describe and provide example for single output port > >> - update to new audio port bindings > >> --- > >> .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ > >> 1 file changed, 179 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt > >> > >> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt > >> new file mode 100644 > >> index 0000000..dd37f14 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt > >> @@ -0,0 +1,179 @@ > >> +Device-Tree bindings for the NXP TDA1997x HDMI receiver > >> + > >> +The TDA19971/73 are HDMI video receivers. > >> + > >> +The TDA19971 Video port output pins can be used as follows: > >> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] > >> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] > >> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] > >> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] > >> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] > >> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) > >> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) > >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) > >> + > >> +The TDA19973 Video port output pins can be used as follows: > >> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] > >> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] > >> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] > >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) > >> + > >> +The Video port output pins are mapped via 4-bit 'pin groups' allowing > >> +for a variety of connection possibilities including swapping pin order within > >> +pin groups. The video_portcfg device-tree property consists of register mapping > >> +pairs which map a chip-specific VP output register to a 4-bit pin group. If > >> +the pin group needs to be bit-swapped you can use the *_S pin-group defines. > >> + > >> +Required Properties: > >> + - compatible : > >> + - "nxp,tda19971" for the TDA19971 > >> + - "nxp,tda19973" for the TDA19973 > >> + - reg : I2C slave address > >> + - interrupts : The interrupt number > >> + - DOVDD-supply : Digital I/O supply > >> + - DVDD-supply : Digital Core supply > >> + - AVDD-supply : Analog supply > >> + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. > >> + > >> +Optional Properties: > >> + - nxp,audout-format : DAI bus format: "i2s" or "spdif". > >> + - nxp,audout-width : width of audio output data bus (1-4). > >> + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). > >> + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec > >> + mclk. > >> + > >> +The device node must contain one 'port' child node for its digital output > >> +video port, in accordance with the video interface bindings defined in > >> +Documentation/devicetree/bindings/media/video-interfaces.txt. > > > > Could you add that this port has one endpoint node as well? (Unless you > > support multiple, that is.) > > Sure... will clarify as: > > The device node must contain one endpoint 'port' child node for its > digital output > video port, in accordance with the video interface bindings defined in > Documentation/devicetree/bindings/media/video-interfaces.txt. I think it'd be clearer if you just add "The port node shall contain one endpoint child node". > > >> + > >> +Optional Endpoint Properties: > >> + The following three properties are defined in video-interfaces.txt and > >> + are valid for source endpoints only: > > > > Transmitters? Don't you have an endpoint only in the port representing the > > transmitter? > > I'm not usre what you mean. > > The TDA1997x is an HDMI receiver meaning it receives HDMI and decodes > it to a parallel video bus. HDMI transmitters are the opposite. The parallel bus. If you mean that, then you could just say that. "Source endpoint" is a bit vague, or requires knowing V4L2. -- Sakari Ailus e-mail: sakari.ailus@xxxxxx -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
