On Thu, Nov 23, 2017 at 12:25 AM, Sakari Ailus <sakari.ailus@xxxxxx> wrote: > On Wed, Nov 22, 2017 at 08:37:04PM -0800, Tim Harvey wrote: >> On Tue, Nov 21, 2017 at 11:36 PM, Sakari Ailus <sakari.ailus@xxxxxx> wrote: >> > Hi Tim, >> > >> > On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote: >> >> Cc: Rob Herring <robh@xxxxxxxxxx> >> >> Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx> >> >> --- >> >> v3: >> >> - fix typo >> >> >> >> v2: >> >> - add vendor prefix and remove _ from vidout-portcfg >> >> - remove _ from labels >> >> - remove max-pixel-rate property >> >> - describe and provide example for single output port >> >> - update to new audio port bindings >> >> --- >> >> .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ >> >> 1 file changed, 179 insertions(+) >> >> create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> >> >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> >> new file mode 100644 >> >> index 0000000..dd37f14 >> >> --- /dev/null >> >> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> >> @@ -0,0 +1,179 @@ >> >> +Device-Tree bindings for the NXP TDA1997x HDMI receiver >> >> + >> >> +The TDA19971/73 are HDMI video receivers. >> >> + >> >> +The TDA19971 Video port output pins can be used as follows: >> >> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] >> >> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] >> >> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] >> >> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] >> >> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] >> >> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) >> >> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) >> >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) >> >> + >> >> +The TDA19973 Video port output pins can be used as follows: >> >> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] >> >> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] >> >> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] >> >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) >> >> + >> >> +The Video port output pins are mapped via 4-bit 'pin groups' allowing >> >> +for a variety of connection possibilities including swapping pin order within >> >> +pin groups. The video_portcfg device-tree property consists of register mapping >> >> +pairs which map a chip-specific VP output register to a 4-bit pin group. If >> >> +the pin group needs to be bit-swapped you can use the *_S pin-group defines. >> >> + >> >> +Required Properties: >> >> + - compatible : >> >> + - "nxp,tda19971" for the TDA19971 >> >> + - "nxp,tda19973" for the TDA19973 >> >> + - reg : I2C slave address >> >> + - interrupts : The interrupt number >> >> + - DOVDD-supply : Digital I/O supply >> >> + - DVDD-supply : Digital Core supply >> >> + - AVDD-supply : Analog supply >> >> + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. >> >> + >> >> +Optional Properties: >> >> + - nxp,audout-format : DAI bus format: "i2s" or "spdif". >> >> + - nxp,audout-width : width of audio output data bus (1-4). >> >> + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). >> >> + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec >> >> + mclk. >> >> + >> >> +The device node must contain one 'port' child node for its digital output >> >> +video port, in accordance with the video interface bindings defined in >> >> +Documentation/devicetree/bindings/media/video-interfaces.txt. >> > >> > Could you add that this port has one endpoint node as well? (Unless you >> > support multiple, that is.) >> >> Sure... will clarify as: >> >> The device node must contain one endpoint 'port' child node for its >> digital output >> video port, in accordance with the video interface bindings defined in >> Documentation/devicetree/bindings/media/video-interfaces.txt. > > I think it'd be clearer if you just add "The port node shall contain one > endpoint child node". ok > >> >> >> + >> >> +Optional Endpoint Properties: >> >> + The following three properties are defined in video-interfaces.txt and >> >> + are valid for source endpoints only: >> > >> > Transmitters? Don't you have an endpoint only in the port representing the >> > transmitter? >> >> I'm not usre what you mean. >> >> The TDA1997x is an HDMI receiver meaning it receives HDMI and decodes >> it to a parallel video bus. HDMI transmitters are the opposite. > > The parallel bus. If you mean that, then you could just say that. "Source > endpoint" is a bit vague, or requires knowing V4L2. > agreed Thanks, Tim -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
