From: Jianguo Sun <sunjianguo1@xxxxxxxxxx> Add combo phy driver for HiSilicon STB SoCs. This phy can be used as pcie-phy, sata-phy or usb-phy. Signed-off-by: Jianguo Sun <sunjianguo1@xxxxxxxxxx> Signed-off-by: Shawn Guo <shawn.guo@xxxxxxxxxx> --- drivers/phy/hisilicon/Kconfig | 9 ++ drivers/phy/hisilicon/Makefile | 1 + drivers/phy/hisilicon/phy-histb-combphy.c | 253 ++++++++++++++++++++++++++++++ 3 files changed, 263 insertions(+) create mode 100644 drivers/phy/hisilicon/phy-histb-combphy.c diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig index 6164c4cd0f65..d9afe2b12827 100644 --- a/drivers/phy/hisilicon/Kconfig +++ b/drivers/phy/hisilicon/Kconfig @@ -11,6 +11,15 @@ config PHY_HI6220_USB To compile this driver as a module, choose M here. +config PHY_HISTB_COMBPHY + tristate "HiSilicon STB SoCs COMBPHY support" + depends on (ARCH_HISI && ARM64) || COMPILE_TEST + select GENERIC_PHY + select MFD_SYSCON + help + Enable this to support the HISILICON STB SoCs COMBPHY. + If unsure, say N. + config PHY_HIX5HD2_SATA tristate "HIX5HD2 SATA PHY Driver" depends on ARCH_HIX5HD2 && OF && HAS_IOMEM diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile index 541b348187a8..5e8e2dfa8c37 100644 --- a/drivers/phy/hisilicon/Makefile +++ b/drivers/phy/hisilicon/Makefile @@ -1,2 +1,3 @@ obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o +obj-$(CONFIG_PHY_HISTB_COMBPHY) += phy-histb-combphy.o obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o diff --git a/drivers/phy/hisilicon/phy-histb-combphy.c b/drivers/phy/hisilicon/phy-histb-combphy.c new file mode 100644 index 000000000000..24c39c199a97 --- /dev/null +++ b/drivers/phy/hisilicon/phy-histb-combphy.c @@ -0,0 +1,253 @@ +/* + * COMBPHY driver for HiSilicon STB SoCs + * + * Copyright (C) 2016-2017 HiSilicon Co., Ltd. http://www.hisilicon.com + * + * Authors: Jianguo Sun <sunjianguo1@xxxxxxxxxx> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/phy/phy.h> +#include <linux/regmap.h> +#include <linux/reset.h> +#include <dt-bindings/phy/phy.h> + +#define PERI_CTRL 0x8 +#define COMBPHY1_MODE_MASK GENMASK(12, 11) +#define COMBPHY1_MODE_SHIFT 11 +#define COMBPHY_MODE_PCIE 0 +#define COMBPHY_MODE_USB3 1 +#define COMBPHY_MODE_SATA 2 + +#define COMBPHY_CFG_REG 0x0 +#define COMBPHY_BYPASS_CODEC BIT(31) +#define COMBPHY_TEST_WRITE BIT(24) +#define COMBPHY_TEST_DATA_SHIFT 20 +#define COMBPHY_TEST_DATA_MASK GENMASK(23, 20) +#define COMBPHY_TEST_ADDR_SHIFT 12 +#define COMBPHY_TEST_ADDR_MASK GENMASK(16, 12) +#define COMBPHY_CLKREF_OUT_OEN BIT(0) + +struct histb_combphy_priv { + void __iomem *mmio; + struct regmap *syscon; + struct reset_control *por_rst; + struct clk *ref_clk; + struct phy *phy; + int phy_mode; + int phy_id; +}; + +static void nano_register_write(struct histb_combphy_priv *priv, + u32 addr, u32 data) +{ + void __iomem *reg = priv->mmio + COMBPHY_CFG_REG; + u32 val; + + /* Set up address and data for the write */ + val = readl(reg); + val &= ~COMBPHY_TEST_ADDR_MASK; + val |= addr << COMBPHY_TEST_ADDR_SHIFT; + val &= ~COMBPHY_TEST_DATA_MASK; + val |= data << COMBPHY_TEST_DATA_SHIFT; + writel(val, reg); + + /* Flip strobe control to trigger the write */ + val &= ~COMBPHY_TEST_WRITE; + writel(val, reg); + val |= COMBPHY_TEST_WRITE; + writel(val, reg); +} + +static int histb_combphy_set_mode(struct histb_combphy_priv *priv) +{ + struct regmap *syscon = priv->syscon; + u32 mode; + + switch (priv->phy_mode) { + case PHY_TYPE_SATA: + mode = COMBPHY_MODE_SATA; + break; + case PHY_TYPE_PCIE: + mode = COMBPHY_MODE_PCIE; + break; + case PHY_TYPE_USB3: + mode = COMBPHY_MODE_USB3; + break; + default: + return -EINVAL; + } + + return regmap_update_bits(syscon, PERI_CTRL, COMBPHY1_MODE_MASK, + mode << COMBPHY1_MODE_SHIFT); +} + +static int histb_combphy_init(struct phy *phy) +{ + struct histb_combphy_priv *priv = phy_get_drvdata(phy); + u32 val; + int ret; + + /* PHY0 doesn't support mode setting */ + if (priv->phy_id != 0) { + ret = histb_combphy_set_mode(priv); + if (ret) + return ret; + } + + /* Clear bypass bit to enable encoding/decoding */ + val = readl(priv->mmio + COMBPHY_CFG_REG); + val &= ~COMBPHY_BYPASS_CODEC; + writel(val, priv->mmio + COMBPHY_CFG_REG); + + ret = clk_prepare_enable(priv->ref_clk); + if (ret) + return ret; + + reset_control_deassert(priv->por_rst); + + /* Enable EP clock */ + val = readl(priv->mmio + COMBPHY_CFG_REG); + val |= COMBPHY_CLKREF_OUT_OEN; + writel(val, priv->mmio + COMBPHY_CFG_REG); + + /* Need to wait for EP clock stable */ + mdelay(5); + + /* Configure nano phy registers as suggested by vendor */ + nano_register_write(priv, 0x1, 0x8); + nano_register_write(priv, 0xc, 0x9); + nano_register_write(priv, 0x1a, 0x4); + + return 0; +} + +static int histb_combphy_exit(struct phy *phy) +{ + struct histb_combphy_priv *priv = phy_get_drvdata(phy); + u32 val; + + /* Disable EP clock */ + val = readl(priv->mmio + COMBPHY_CFG_REG); + val &= ~COMBPHY_CLKREF_OUT_OEN; + writel(val, priv->mmio + COMBPHY_CFG_REG); + + reset_control_assert(priv->por_rst); + clk_disable_unprepare(priv->ref_clk); + + return 0; +} + +static const struct phy_ops histb_combphy_ops = { + .init = histb_combphy_init, + .exit = histb_combphy_exit, + .owner = THIS_MODULE, +}; + +static struct phy *histb_combphy_xlate(struct device *dev, + struct of_phandle_args *args) +{ + struct histb_combphy_priv *priv = dev_get_drvdata(dev); + + if (args->args_count < 1) { + dev_err(dev, "invalid number of arguments\n"); + return ERR_PTR(-EINVAL); + } + + priv->phy_mode = args->args[0]; + + if (priv->phy_mode < PHY_TYPE_SATA || priv->phy_mode > PHY_TYPE_USB3) { + dev_err(dev, "invalid phy mode argument\n"); + return ERR_PTR(-EINVAL); + } + + if (priv->phy_id == 0 && priv->phy_mode != PHY_TYPE_USB3) { + dev_err(dev, "PHY0 works in USB3 mode only\n"); + return ERR_PTR(-EINVAL); + } + + return priv->phy; +} + +static int histb_combphy_probe(struct platform_device *pdev) +{ + struct phy_provider *phy_provider; + struct device *dev = &pdev->dev; + struct histb_combphy_priv *priv; + struct device_node *np = dev->of_node; + struct resource *res; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->mmio = devm_ioremap_resource(dev, res); + if (IS_ERR(priv->mmio)) { + ret = PTR_ERR(priv->mmio); + return ret; + } + + priv->syscon = syscon_node_to_regmap(np->parent); + if (IS_ERR(priv->syscon)) { + dev_err(dev, "failed to find peri_ctrl syscon regmap\n"); + return PTR_ERR(priv->syscon); + } + + priv->phy_id = of_alias_get_id(np, "combphy"); + if (priv->phy_id < 0) + priv->phy_id = 0; + + priv->ref_clk = devm_clk_get(dev, NULL); + if (IS_ERR(priv->ref_clk)) { + dev_err(dev, "failed to find ref clock\n"); + return PTR_ERR(priv->ref_clk); + } + + priv->por_rst = devm_reset_control_get(dev, NULL); + if (IS_ERR(priv->por_rst)) { + dev_err(dev, "failed to get poweron reset\n"); + return PTR_ERR(priv->por_rst); + } + + priv->phy = devm_phy_create(dev, NULL, &histb_combphy_ops); + if (IS_ERR(priv->phy)) { + dev_err(dev, "failed to create combphy\n"); + return PTR_ERR(priv->phy); + } + + dev_set_drvdata(dev, priv); + phy_set_drvdata(priv->phy, priv); + + phy_provider = devm_of_phy_provider_register(dev, histb_combphy_xlate); + return PTR_ERR_OR_ZERO(phy_provider); +} + +static const struct of_device_id histb_combphy_of_match[] = { + { .compatible = "hisilicon,hi3798cv200-combphy" }, + { }, +}; +MODULE_DEVICE_TABLE(of, histb_combphy_of_match); + +static struct platform_driver histb_combphy_driver = { + .probe = histb_combphy_probe, + .driver = { + .name = "combphy", + .of_match_table = histb_combphy_of_match, + }, +}; +module_platform_driver(histb_combphy_driver); + +MODULE_DESCRIPTION("HiSilicon STB COMBPHY driver"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
