Hi Rob
On 27 September 2017 at 22:51, Rob Herring <robh@xxxxxxxxxx> wrote:
> On Fri, Sep 22, 2017 at 05:07:22PM +0100, Dave Stevenson wrote:
>> Hi Stefan
>>
>> On 22 September 2017 at 07:45, Stefan Wahren <stefan.wahren@xxxxxxxx> wrote:
>> > Hi Dave,
>> >
>> >> Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx> hat am 20. September 2017 um 18:07 geschrieben:
>> >>
>> >>
>> >> Document the DT bindings for the CSI2/CCP2 receiver peripheral
>> >> (known as Unicam) on BCM283x SoCs.
>> >>
>> >> Signed-off-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
>> >> ---
>> >>
>> >> Changes since v2
>> >> - Removed all references to Linux drivers.
>> >> - Reworded section about disabling the firmware driver.
>> >> - Renamed clock from "lp_clock" to "lp" in description and example.
>> >> - Referred to video-interfaces.txt and stated requirements on remote-endpoint
>> >> and data-lanes.
>> >> - Corrected typo in example from csi to csi1.
>> >> - Removed unnecessary #address-cells and #size-cells in example.
>> >> - Removed setting of status from the example.
>> >>
>> >> .../devicetree/bindings/media/bcm2835-unicam.txt | 85 ++++++++++++++++++++++
>> >> 1 file changed, 85 insertions(+)
>> >> create mode 100644 Documentation/devicetree/bindings/media/bcm2835-unicam.txt
>> >>
>> >> diff --git a/Documentation/devicetree/bindings/media/bcm2835-unicam.txt b/Documentation/devicetree/bindings/media/bcm2835-unicam.txt
>> >> new file mode 100644
>> >> index 0000000..7714fb3
>> >> --- /dev/null
>> >> +++ b/Documentation/devicetree/bindings/media/bcm2835-unicam.txt
>> >> @@ -0,0 +1,85 @@
>> >> +Broadcom BCM283x Camera Interface (Unicam)
>> >> +------------------------------------------
>> >> +
>> >> +The Unicam block on BCM283x SoCs is the receiver for either
>> >> +CSI-2 or CCP2 data from image sensors or similar devices.
>> >> +
>> >> +The main platform using this SoC is the Raspberry Pi family of boards.
>> >> +On the Pi the VideoCore firmware can also control this hardware block,
>> >> +and driving it from two different processors will cause issues.
>> >> +To avoid this, the firmware checks the device tree configuration
>> >> +during boot. If it finds device tree nodes called csi0 or csi1 then
>> >> +it will stop the firmware accessing the block, and it can then
>> >> +safely be used via the device tree binding.
>> >> +
>> >> +Required properties:
>> >> +===================
>> >> +- compatible : must be "brcm,bcm2835-unicam".
>> >> +- reg : physical base address and length of the register sets for the
>> >> + device.
>> >> +- interrupts : should contain the IRQ line for this Unicam instance.
>> >> +- clocks : list of clock specifiers, corresponding to entries in
>> >> + clock-names property.
>> >> +- clock-names : must contain an "lp" entry, matching entries in the
>> >> + clocks property.
>> >> +
>> >> +Unicam supports a single port node. It should contain one 'port' child node
>> >> +with child 'endpoint' node. Please refer to the bindings defined in
>> >> +Documentation/devicetree/bindings/media/video-interfaces.txt.
>> >> +
>> >> +Within the endpoint node the "remote-endpoint" and "data-lanes" properties
>> >> +are mandatory.
>> >> +Data lane reordering is not supported so the data lanes must be in order,
>> >> +starting at 1. The number of data lanes should represent the number of
>> >> +usable lanes for the hardware block. That may be limited by either the SoC or
>> >> +how the platform presents the interface, and the lower value must be used.
>> >> +
>> >> +Lane reordering is not supported on the clock lane either, so the optional
>> >> +property "clock-lane" will implicitly be <0>.
>> >> +Similarly lane inversion is not supported, therefore "lane-polarities" will
>> >> +implicitly be <0 0 0 0 0>.
>> >> +Neither of these values will be checked.
>> >> +
>> >> +Example:
>> >> + csi1: csi1@7e801000 {
>> >> + compatible = "brcm,bcm2835-unicam";
>> >> + reg = <0x7e801000 0x800>,
>> >> + <0x7e802004 0x4>;
>> >
>> > sorry, i didn't noticed this before. I'm afraid this is using a small range of the CMI. Are there possible other users of this range? Does it make sense to handle this by a separate clock driver?
>>
>> CMI (Clock Manager Image) consists of a total of 4 registers.
>> 0x7e802000 is CMI_CAM0, with only bits 0-5 used for gating and
>> inversion of the clock and data lanes (2 data lanes available on
>> CAM0).
>> 0x7e802004 is CMI_CAM1, with only bits 0-9 used for gating and
>> inversion of the clock and data lanes (4 data lanes available on
>> CAM1).
>> 0x7e802008 is CMI_CAMTEST which I have no documentation or drivers for.
>> 0x7e802010 is CMI_USBCTL. Only bit 6 is documented and is a reset. The
>> default value is the required value. Nothing touches it that I can
>> find.
>>
>> The range listed only covers the one register associated with that
>> Unicam instance, so no other users. The other two aren't touched.
>> Do 16 active register bits solely for camera clock gating really
>> warrant a full clock driver?
>
> You should describe all the registers in DT, not just what the driver
> (currently) uses.
I'm not clear what you're asking for here.
This binding is for the Unicam block, not for CMI (Clock Manager
Imaging). In order for a Unicam instance to work, it needs to enable
the relevant clock gating via 1 CMI register, and it will only ever be
one register.
Eric and Stefan as the platform maintainers have already both
acknowledged that a full clock driver for the CMI block is not
warranted - the only user would be this driver, and the other
registers in the CMI block are not useful.
Do you want a random text description of a different block within this
binding? Or are you requesting a full clock driver for the CMI block?
Or that all Unicam instances should be mapping the whole 4 register
range of CMI, and then somehow working out which register within that
block they should be mapping?
Regards,
Dave
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
