Re: [PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi,

On Sun, Feb 26, 2017 at 9:19 AM, Icenowy Zheng <icenowy@xxxxxxxx> wrote:
> From: Andre Przywara <andre.przywara@xxxxxxx>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
>
> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
> [Icenowy: also split out mmc, as well as pio and ccu's compatible]
> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxxx>
> ---
> Changes in v3:
> - Use label-based syntax to reference nodes in H3 DTSI file.
> Changes in v2:
> - Rebase on current linux-next (because of the add of audio codec)
>
>  arch/arm/boot/dts/sun8i-h3.dtsi                    | 789 ++++-----------------
>  .../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi}   |  87 +--
>  2 files changed, 148 insertions(+), 728 deletions(-)
>  rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%)
>  copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> dissimilarity index 81%
> index 8a4d7894a11f..4209d974c3f4 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -1,648 +1,141 @@
> -/*
> - * Copyright (C) 2015 Jens Kuske <jenskuske@xxxxxxxxx>
> - *
> - * This file is dual-licensed: you can use it either under the terms
> - * of the GPL or the X11 license, at your option. Note that this dual
> - * licensing only applies to this file, and not this project as a
> - * whole.
> - *
> - *  a) This file is free software; you can redistribute it and/or
> - *     modify it under the terms of the GNU General Public License as
> - *     published by the Free Software Foundation; either version 2 of the
> - *     License, or (at your option) any later version.
> - *
> - *     This file is distributed in the hope that it will be useful,
> - *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> - *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - *     GNU General Public License for more details.
> - *
> - * Or, alternatively,
> - *
> - *  b) Permission is hereby granted, free of charge, to any person
> - *     obtaining a copy of this software and associated documentation
> - *     files (the "Software"), to deal in the Software without
> - *     restriction, including without limitation the rights to use,
> - *     copy, modify, merge, publish, distribute, sublicense, and/or
> - *     sell copies of the Software, and to permit persons to whom the
> - *     Software is furnished to do so, subject to the following
> - *     conditions:
> - *
> - *     The above copyright notice and this permission notice shall be
> - *     included in all copies or substantial portions of the Software.
> - *
> - *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> - *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> - *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> - *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> - *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> - *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> - *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> - *     OTHER DEALINGS IN THE SOFTWARE.
> - */
> -
> -#include "skeleton.dtsi"
> -
> -#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> -#include <dt-bindings/pinctrl/sun4i-a10.h>
> -#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
> -
> -/ {
> -       interrupt-parent = <&gic>;
> -
> -       cpus {
> -               #address-cells = <1>;
> -               #size-cells = <0>;
> -
> -               cpu@0 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <0>;
> -               };
> -
> -               cpu@1 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <1>;
> -               };
> -
> -               cpu@2 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <2>;
> -               };
> -
> -               cpu@3 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <3>;
> -               };
> -       };
> -
> -       timer {
> -               compatible = "arm,armv7-timer";
> -               interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> -                            <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> -                            <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> -                            <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> -       };
> -
> -       clocks {
> -               #address-cells = <1>;
> -               #size-cells = <1>;
> -               ranges;
> -
> -               osc24M: osc24M_clk {
> -                       #clock-cells = <0>;
> -                       compatible = "fixed-clock";
> -                       clock-frequency = <24000000>;
> -                       clock-output-names = "osc24M";
> -               };
> -
> -               osc32k: osc32k_clk {
> -                       #clock-cells = <0>;
> -                       compatible = "fixed-clock";
> -                       clock-frequency = <32768>;
> -                       clock-output-names = "osc32k";
> -               };
> -
> -               apb0: apb0_clk {
> -                       compatible = "fixed-factor-clock";
> -                       #clock-cells = <0>;
> -                       clock-div = <1>;
> -                       clock-mult = <1>;
> -                       clocks = <&osc24M>;
> -                       clock-output-names = "apb0";
> -               };
> -
> -               apb0_gates: clk@01f01428 {
> -                       compatible = "allwinner,sun8i-h3-apb0-gates-clk",
> -                                    "allwinner,sun4i-a10-gates-clk";
> -                       reg = <0x01f01428 0x4>;
> -                       #clock-cells = <1>;
> -                       clocks = <&apb0>;
> -                       clock-indices = <0>, <1>;
> -                       clock-output-names = "apb0_pio", "apb0_ir";
> -               };
> -
> -               ir_clk: ir_clk@01f01454 {
> -                       compatible = "allwinner,sun4i-a10-mod0-clk";
> -                       reg = <0x01f01454 0x4>;
> -                       #clock-cells = <0>;
> -                       clocks = <&osc32k>, <&osc24M>;
> -                       clock-output-names = "ir";
> -               };
> -       };
> -
> -       soc {
> -               compatible = "simple-bus";
> -               #address-cells = <1>;
> -               #size-cells = <1>;
> -               ranges;
> -
> -               dma: dma-controller@01c02000 {
> -                       compatible = "allwinner,sun8i-h3-dma";
> -                       reg = <0x01c02000 0x1000>;
> -                       interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_DMA>;
> -                       resets = <&ccu RST_BUS_DMA>;
> -                       #dma-cells = <1>;
> -               };
> -
> -               mmc0: mmc@01c0f000 {
> -                       compatible = "allwinner,sun7i-a20-mmc";
> -                       reg = <0x01c0f000 0x1000>;
> -                       clocks = <&ccu CLK_BUS_MMC0>,
> -                                <&ccu CLK_MMC0>,
> -                                <&ccu CLK_MMC0_OUTPUT>,
> -                                <&ccu CLK_MMC0_SAMPLE>;
> -                       clock-names = "ahb",
> -                                     "mmc",
> -                                     "output",
> -                                     "sample";
> -                       resets = <&ccu RST_BUS_MMC0>;
> -                       reset-names = "ahb";
> -                       interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               mmc1: mmc@01c10000 {
> -                       compatible = "allwinner,sun7i-a20-mmc";
> -                       reg = <0x01c10000 0x1000>;
> -                       clocks = <&ccu CLK_BUS_MMC1>,
> -                                <&ccu CLK_MMC1>,
> -                                <&ccu CLK_MMC1_OUTPUT>,
> -                                <&ccu CLK_MMC1_SAMPLE>;
> -                       clock-names = "ahb",
> -                                     "mmc",
> -                                     "output",
> -                                     "sample";
> -                       resets = <&ccu RST_BUS_MMC1>;
> -                       reset-names = "ahb";
> -                       interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               mmc2: mmc@01c11000 {
> -                       compatible = "allwinner,sun7i-a20-mmc";
> -                       reg = <0x01c11000 0x1000>;
> -                       clocks = <&ccu CLK_BUS_MMC2>,
> -                                <&ccu CLK_MMC2>,
> -                                <&ccu CLK_MMC2_OUTPUT>,
> -                                <&ccu CLK_MMC2_SAMPLE>;
> -                       clock-names = "ahb",
> -                                     "mmc",
> -                                     "output",
> -                                     "sample";
> -                       resets = <&ccu RST_BUS_MMC2>;
> -                       reset-names = "ahb";
> -                       interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               usbphy: phy@01c19400 {
> -                       compatible = "allwinner,sun8i-h3-usb-phy";
> -                       reg = <0x01c19400 0x2c>,
> -                             <0x01c1a800 0x4>,
> -                             <0x01c1b800 0x4>,
> -                             <0x01c1c800 0x4>,
> -                             <0x01c1d800 0x4>;
> -                       reg-names = "phy_ctrl",
> -                                   "pmu0",
> -                                   "pmu1",
> -                                   "pmu2",
> -                                   "pmu3";
> -                       clocks = <&ccu CLK_USB_PHY0>,
> -                                <&ccu CLK_USB_PHY1>,
> -                                <&ccu CLK_USB_PHY2>,
> -                                <&ccu CLK_USB_PHY3>;
> -                       clock-names = "usb0_phy",
> -                                     "usb1_phy",
> -                                     "usb2_phy",
> -                                     "usb3_phy";
> -                       resets = <&ccu RST_USB_PHY0>,
> -                                <&ccu RST_USB_PHY1>,
> -                                <&ccu RST_USB_PHY2>,
> -                                <&ccu RST_USB_PHY3>;
> -                       reset-names = "usb0_reset",
> -                                     "usb1_reset",
> -                                     "usb2_reset",
> -                                     "usb3_reset";
> -                       status = "disabled";
> -                       #phy-cells = <1>;
> -               };
> -
> -               ehci1: usb@01c1b000 {
> -                       compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> -                       reg = <0x01c1b000 0x100>;
> -                       interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
> -                       resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> -                       phys = <&usbphy 1>;
> -                       phy-names = "usb";
> -                       status = "disabled";
> -               };
> -
> -               ohci1: usb@01c1b400 {
> -                       compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> -                       reg = <0x01c1b400 0x100>;
> -                       interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
> -                                <&ccu CLK_USB_OHCI1>;
> -                       resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> -                       phys = <&usbphy 1>;
> -                       phy-names = "usb";
> -                       status = "disabled";
> -               };
> -
> -               ehci2: usb@01c1c000 {
> -                       compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> -                       reg = <0x01c1c000 0x100>;
> -                       interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
> -                       resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> -                       phys = <&usbphy 2>;
> -                       phy-names = "usb";
> -                       status = "disabled";
> -               };
> -
> -               ohci2: usb@01c1c400 {
> -                       compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> -                       reg = <0x01c1c400 0x100>;
> -                       interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
> -                                <&ccu CLK_USB_OHCI2>;
> -                       resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> -                       phys = <&usbphy 2>;
> -                       phy-names = "usb";
> -                       status = "disabled";
> -               };
> -
> -               ehci3: usb@01c1d000 {
> -                       compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> -                       reg = <0x01c1d000 0x100>;
> -                       interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
> -                       resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> -                       phys = <&usbphy 3>;
> -                       phy-names = "usb";
> -                       status = "disabled";
> -               };
> -
> -               ohci3: usb@01c1d400 {
> -                       compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> -                       reg = <0x01c1d400 0x100>;
> -                       interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
> -                                <&ccu CLK_USB_OHCI3>;
> -                       resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> -                       phys = <&usbphy 3>;
> -                       phy-names = "usb";
> -                       status = "disabled";
> -               };
> -
> -               ccu: clock@01c20000 {
> -                       compatible = "allwinner,sun8i-h3-ccu";
> -                       reg = <0x01c20000 0x400>;
> -                       clocks = <&osc24M>, <&osc32k>;
> -                       clock-names = "hosc", "losc";
> -                       #clock-cells = <1>;
> -                       #reset-cells = <1>;
> -               };
> -
> -               pio: pinctrl@01c20800 {
> -                       compatible = "allwinner,sun8i-h3-pinctrl";
> -                       reg = <0x01c20800 0x400>;
> -                       interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> -                                    <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> -                       clock-names = "apb", "hosc", "losc";
> -                       gpio-controller;
> -                       #gpio-cells = <3>;
> -                       interrupt-controller;
> -                       #interrupt-cells = <3>;
> -
> -                       i2c0_pins: i2c0 {
> -                               pins = "PA11", "PA12";
> -                               function = "i2c0";
> -                       };
> -
> -                       i2c1_pins: i2c1 {
> -                               pins = "PA18", "PA19";
> -                               function = "i2c1";
> -                       };
> -
> -                       i2c2_pins: i2c2 {
> -                               pins = "PE12", "PE13";
> -                               function = "i2c2";
> -                       };
> -
> -                       mmc0_pins_a: mmc0@0 {
> -                               pins = "PF0", "PF1", "PF2", "PF3",
> -                                      "PF4", "PF5";
> -                               function = "mmc0";
> -                               drive-strength = <30>;
> -                               bias-pull-up;
> -                       };
> -
> -                       mmc0_cd_pin: mmc0_cd_pin@0 {
> -                               pins = "PF6";
> -                               function = "gpio_in";
> -                               bias-pull-up;
> -                       };
> -
> -                       mmc1_pins_a: mmc1@0 {
> -                               pins = "PG0", "PG1", "PG2", "PG3",
> -                                      "PG4", "PG5";
> -                               function = "mmc1";
> -                               drive-strength = <30>;
> -                               bias-pull-up;
> -                       };
> -
> -                       mmc2_8bit_pins: mmc2_8bit {
> -                               pins = "PC5", "PC6", "PC8",
> -                                      "PC9", "PC10", "PC11",
> -                                      "PC12", "PC13", "PC14",
> -                                      "PC15", "PC16";
> -                               function = "mmc2";
> -                               drive-strength = <30>;
> -                               bias-pull-up;
> -                       };
> -
> -                       spdif_tx_pins_a: spdif@0 {
> -                               pins = "PA17";
> -                               function = "spdif";
> -                       };
> -
> -                       spi0_pins: spi0 {
> -                               pins = "PC0", "PC1", "PC2", "PC3";
> -                               function = "spi0";
> -                       };
> -
> -                       spi1_pins: spi1 {
> -                               pins = "PA15", "PA16", "PA14", "PA13";
> -                               function = "spi1";
> -                       };
> -
> -                       uart0_pins_a: uart0@0 {
> -                               pins = "PA4", "PA5";
> -                               function = "uart0";
> -                       };
> -
> -                       uart1_pins: uart1 {
> -                               pins = "PG6", "PG7";
> -                               function = "uart1";
> -                       };
> -
> -                       uart1_rts_cts_pins: uart1_rts_cts {
> -                               pins = "PG8", "PG9";
> -                               function = "uart1";
> -                       };
> -
> -                       uart2_pins: uart2 {
> -                               pins = "PA0", "PA1";
> -                               function = "uart2";
> -                       };
> -
> -                       uart3_pins: uart3 {
> -                               pins = "PA13", "PA14";
> -                               function = "uart3";
> -                       };
> -               };
> -
> -               timer@01c20c00 {
> -                       compatible = "allwinner,sun4i-a10-timer";
> -                       reg = <0x01c20c00 0xa0>;
> -                       interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> -                                    <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&osc24M>;
> -               };
> -
> -               spi0: spi@01c68000 {
> -                       compatible = "allwinner,sun8i-h3-spi";
> -                       reg = <0x01c68000 0x1000>;
> -                       interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> -                       clock-names = "ahb", "mod";
> -                       dmas = <&dma 23>, <&dma 23>;
> -                       dma-names = "rx", "tx";
> -                       pinctrl-names = "default";
> -                       pinctrl-0 = <&spi0_pins>;
> -                       resets = <&ccu RST_BUS_SPI0>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               spi1: spi@01c69000 {
> -                       compatible = "allwinner,sun8i-h3-spi";
> -                       reg = <0x01c69000 0x1000>;
> -                       interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> -                       clock-names = "ahb", "mod";
> -                       dmas = <&dma 24>, <&dma 24>;
> -                       dma-names = "rx", "tx";
> -                       pinctrl-names = "default";
> -                       pinctrl-0 = <&spi1_pins>;
> -                       resets = <&ccu RST_BUS_SPI1>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               wdt0: watchdog@01c20ca0 {
> -                       compatible = "allwinner,sun6i-a31-wdt";
> -                       reg = <0x01c20ca0 0x20>;
> -                       interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> -               };
> -
> -               spdif: spdif@01c21000 {
> -                       #sound-dai-cells = <0>;
> -                       compatible = "allwinner,sun8i-h3-spdif";
> -                       reg = <0x01c21000 0x400>;
> -                       interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
> -                       resets = <&ccu RST_BUS_SPDIF>;
> -                       clock-names = "apb", "spdif";
> -                       dmas = <&dma 2>;
> -                       dma-names = "tx";
> -                       status = "disabled";
> -               };
> -
> -               pwm: pwm@01c21400 {
> -                       compatible = "allwinner,sun8i-h3-pwm";
> -                       reg = <0x01c21400 0x8>;
> -                       clocks = <&osc24M>;
> -                       #pwm-cells = <3>;
> -                       status = "disabled";
> -               };
> -
> -               codec: codec@01c22c00 {
> -                       #sound-dai-cells = <0>;
> -                       compatible = "allwinner,sun8i-h3-codec";
> -                       reg = <0x01c22c00 0x400>;
> -                       interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
> -                       clock-names = "apb", "codec";
> -                       resets = <&ccu RST_BUS_CODEC>;
> -                       dmas = <&dma 15>, <&dma 15>;
> -                       dma-names = "rx", "tx";
> -                       allwinner,codec-analog-controls = <&codec_analog>;
> -                       status = "disabled";
> -               };
> -
> -               uart0: serial@01c28000 {
> -                       compatible = "snps,dw-apb-uart";
> -                       reg = <0x01c28000 0x400>;
> -                       interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> -                       reg-shift = <2>;
> -                       reg-io-width = <4>;
> -                       clocks = <&ccu CLK_BUS_UART0>;
> -                       resets = <&ccu RST_BUS_UART0>;
> -                       dmas = <&dma 6>, <&dma 6>;
> -                       dma-names = "rx", "tx";
> -                       status = "disabled";
> -               };
> -
> -               uart1: serial@01c28400 {
> -                       compatible = "snps,dw-apb-uart";
> -                       reg = <0x01c28400 0x400>;
> -                       interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> -                       reg-shift = <2>;
> -                       reg-io-width = <4>;
> -                       clocks = <&ccu CLK_BUS_UART1>;
> -                       resets = <&ccu RST_BUS_UART1>;
> -                       dmas = <&dma 7>, <&dma 7>;
> -                       dma-names = "rx", "tx";
> -                       status = "disabled";
> -               };
> -
> -               uart2: serial@01c28800 {
> -                       compatible = "snps,dw-apb-uart";
> -                       reg = <0x01c28800 0x400>;
> -                       interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> -                       reg-shift = <2>;
> -                       reg-io-width = <4>;
> -                       clocks = <&ccu CLK_BUS_UART2>;
> -                       resets = <&ccu RST_BUS_UART2>;
> -                       dmas = <&dma 8>, <&dma 8>;
> -                       dma-names = "rx", "tx";
> -                       status = "disabled";
> -               };
> -
> -               uart3: serial@01c28c00 {
> -                       compatible = "snps,dw-apb-uart";
> -                       reg = <0x01c28c00 0x400>;
> -                       interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> -                       reg-shift = <2>;
> -                       reg-io-width = <4>;
> -                       clocks = <&ccu CLK_BUS_UART3>;
> -                       resets = <&ccu RST_BUS_UART3>;
> -                       dmas = <&dma 9>, <&dma 9>;
> -                       dma-names = "rx", "tx";
> -                       status = "disabled";
> -               };
> -
> -               i2c0: i2c@01c2ac00 {
> -                       compatible = "allwinner,sun6i-a31-i2c";
> -                       reg = <0x01c2ac00 0x400>;
> -                       interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_I2C0>;
> -                       resets = <&ccu RST_BUS_I2C0>;
> -                       pinctrl-names = "default";
> -                       pinctrl-0 = <&i2c0_pins>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               i2c1: i2c@01c2b000 {
> -                       compatible = "allwinner,sun6i-a31-i2c";
> -                       reg = <0x01c2b000 0x400>;
> -                       interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_I2C1>;
> -                       resets = <&ccu RST_BUS_I2C1>;
> -                       pinctrl-names = "default";
> -                       pinctrl-0 = <&i2c1_pins>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               i2c2: i2c@01c2b400 {
> -                       compatible = "allwinner,sun6i-a31-i2c";
> -                       reg = <0x01c2b000 0x400>;
> -                       interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&ccu CLK_BUS_I2C2>;
> -                       resets = <&ccu RST_BUS_I2C2>;
> -                       pinctrl-names = "default";
> -                       pinctrl-0 = <&i2c2_pins>;
> -                       status = "disabled";
> -                       #address-cells = <1>;
> -                       #size-cells = <0>;
> -               };
> -
> -               gic: interrupt-controller@01c81000 {
> -                       compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> -                       reg = <0x01c81000 0x1000>,
> -                             <0x01c82000 0x2000>,
> -                             <0x01c84000 0x2000>,
> -                             <0x01c86000 0x2000>;
> -                       interrupt-controller;
> -                       #interrupt-cells = <3>;
> -                       interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> -               };
> -
> -               rtc: rtc@01f00000 {
> -                       compatible = "allwinner,sun6i-a31-rtc";
> -                       reg = <0x01f00000 0x54>;
> -                       interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> -                                    <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> -               };
> -
> -               apb0_reset: reset@01f014b0 {
> -                       reg = <0x01f014b0 0x4>;
> -                       compatible = "allwinner,sun6i-a31-clock-reset";
> -                       #reset-cells = <1>;
> -               };
> -
> -               codec_analog: codec-analog@01f015c0 {
> -                       compatible = "allwinner,sun8i-h3-codec-analog";
> -                       reg = <0x01f015c0 0x4>;
> -               };
> -
> -               ir: ir@01f02000 {
> -                       compatible = "allwinner,sun5i-a13-ir";
> -                       clocks = <&apb0_gates 1>, <&ir_clk>;
> -                       clock-names = "apb", "ir";
> -                       resets = <&apb0_reset 1>;
> -                       interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> -                       reg = <0x01f02000 0x40>;
> -                       status = "disabled";
> -               };
> -
> -               r_pio: pinctrl@01f02c00 {
> -                       compatible = "allwinner,sun8i-h3-r-pinctrl";
> -                       reg = <0x01f02c00 0x400>;
> -                       interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> -                       clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
> -                       clock-names = "apb", "hosc", "losc";
> -                       resets = <&apb0_reset 0>;
> -                       gpio-controller;
> -                       #gpio-cells = <3>;
> -                       interrupt-controller;
> -                       #interrupt-cells = <3>;
> -
> -                       ir_pins_a: ir@0 {
> -                               pins = "PL11";
> -                               function = "s_cir_rx";
> -                       };
> -               };
> -       };
> -};
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@xxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "sunxi-h3-h5.dtsi"
> +
> +/ {
> +       interrupt-parent = <&gic>;
> +
> +       cpus {
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               cpu@0 {
> +                       compatible = "arm,cortex-a7";
> +                       device_type = "cpu";
> +                       reg = <0>;
> +               };
> +
> +               cpu@1 {
> +                       compatible = "arm,cortex-a7";
> +                       device_type = "cpu";
> +                       reg = <1>;
> +               };
> +
> +               cpu@2 {
> +                       compatible = "arm,cortex-a7";
> +                       device_type = "cpu";
> +                       reg = <2>;
> +               };
> +
> +               cpu@3 {
> +                       compatible = "arm,cortex-a7";
> +                       device_type = "cpu";
> +                       reg = <3>;
> +               };
> +       };
> +
> +       timer {
> +               compatible = "arm,armv7-timer";
> +               interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +                            <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> +       };
> +
> +       soc {
> +               gic: interrupt-controller@01c81000 {
> +                       compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> +                       reg = <0x01c81000 0x1000>,
> +                             <0x01c82000 0x2000>,
> +                             <0x01c84000 0x2000>,
> +                             <0x01c86000 0x2000>;
> +                       interrupt-controller;
> +                       #interrupt-cells = <3>;
> +                       interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +               };
> +       };
> +};
> +
> +&ccu {
> +       compatible = "allwinner,sun8i-h3-ccu";
> +};
> +
> +&mmc0 {
> +       compatible = "allwinner,sun7i-a20-mmc";
> +       clocks = <&ccu CLK_BUS_MMC0>,
> +                <&ccu CLK_MMC0>,
> +                <&ccu CLK_MMC0_OUTPUT>,
> +                <&ccu CLK_MMC0_SAMPLE>;
> +       clock-names = "ahb",
> +                     "mmc",
> +                     "output",
> +                     "sample";
> +};
> +
> +&mmc1 {
> +       compatible = "allwinner,sun7i-a20-mmc";
> +       clocks = <&ccu CLK_BUS_MMC1>,
> +                <&ccu CLK_MMC1>,
> +                <&ccu CLK_MMC1_OUTPUT>,
> +                <&ccu CLK_MMC1_SAMPLE>;
> +       clock-names = "ahb",
> +                     "mmc",
> +                     "output",
> +                     "sample";
> +};
> +
> +&mmc2 {
> +       compatible = "allwinner,sun7i-a20-mmc";
> +       clocks = <&ccu CLK_BUS_MMC2>,
> +                <&ccu CLK_MMC2>,
> +                <&ccu CLK_MMC2_OUTPUT>,
> +                <&ccu CLK_MMC2_SAMPLE>;
> +       clock-names = "ahb",
> +                     "mmc",
> +                     "output",
> +                     "sample";
> +};
> +
> +&pio {
> +       compatible = "allwinner,sun8i-h3-pinctrl";
> +};
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> similarity index 88%
> copy from arch/arm/boot/dts/sun8i-h3.dtsi
> copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
> index 8a4d7894a11f..966dc4211c4d 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -40,52 +40,14 @@
>   *     OTHER DEALINGS IN THE SOFTWARE.
>   */
>
> -#include "skeleton.dtsi"
> -
>  #include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/pinctrl/sun4i-a10.h>
>  #include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
>
>  / {
> -       interrupt-parent = <&gic>;
> -
> -       cpus {
> -               #address-cells = <1>;
> -               #size-cells = <0>;
> -
> -               cpu@0 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <0>;
> -               };
> -
> -               cpu@1 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <1>;
> -               };
> -
> -               cpu@2 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <2>;
> -               };
> -
> -               cpu@3 {
> -                       compatible = "arm,cortex-a7";
> -                       device_type = "cpu";
> -                       reg = <3>;
> -               };
> -       };
> -
> -       timer {
> -               compatible = "arm,armv7-timer";
> -               interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> -                            <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> -                            <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> -                            <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> -       };
> +       #address-cells = <1>;
> +       #size-cells = <1>;
>
>         clocks {
>                 #address-cells = <1>;
> @@ -150,16 +112,8 @@
>                 };
>
>                 mmc0: mmc@01c0f000 {
> -                       compatible = "allwinner,sun7i-a20-mmc";
> +                       /* compatible and clocks are in per SoC .dtsi file */
>                         reg = <0x01c0f000 0x1000>;
> -                       clocks = <&ccu CLK_BUS_MMC0>,
> -                                <&ccu CLK_MMC0>,
> -                                <&ccu CLK_MMC0_OUTPUT>,
> -                                <&ccu CLK_MMC0_SAMPLE>;
> -                       clock-names = "ahb",
> -                                     "mmc",
> -                                     "output",
> -                                     "sample";
>                         resets = <&ccu RST_BUS_MMC0>;
>                         reset-names = "ahb";
>                         interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> @@ -169,16 +123,8 @@
>                 };
>
>                 mmc1: mmc@01c10000 {
> -                       compatible = "allwinner,sun7i-a20-mmc";
> +                       /* compatible and clocks are in per SoC .dtsi file */
>                         reg = <0x01c10000 0x1000>;
> -                       clocks = <&ccu CLK_BUS_MMC1>,
> -                                <&ccu CLK_MMC1>,
> -                                <&ccu CLK_MMC1_OUTPUT>,
> -                                <&ccu CLK_MMC1_SAMPLE>;
> -                       clock-names = "ahb",
> -                                     "mmc",
> -                                     "output",
> -                                     "sample";
>                         resets = <&ccu RST_BUS_MMC1>;
>                         reset-names = "ahb";
>                         interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> @@ -188,16 +134,8 @@
>                 };
>
>                 mmc2: mmc@01c11000 {
> -                       compatible = "allwinner,sun7i-a20-mmc";
> +                       /* compatible and clocks are in per SoC .dtsi file */
>                         reg = <0x01c11000 0x1000>;
> -                       clocks = <&ccu CLK_BUS_MMC2>,
> -                                <&ccu CLK_MMC2>,
> -                                <&ccu CLK_MMC2_OUTPUT>,
> -                                <&ccu CLK_MMC2_SAMPLE>;
> -                       clock-names = "ahb",
> -                                     "mmc",
> -                                     "output",
> -                                     "sample";
>                         resets = <&ccu RST_BUS_MMC2>;
>                         reset-names = "ahb";
>                         interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> @@ -308,7 +246,7 @@
>                 };
>
>                 ccu: clock@01c20000 {
> -                       compatible = "allwinner,sun8i-h3-ccu";
> +                       /* compatible is in per SoC .dtsi file */
>                         reg = <0x01c20000 0x400>;
>                         clocks = <&osc24M>, <&osc32k>;
>                         clock-names = "hosc", "losc";
> @@ -317,7 +255,7 @@
>                 };
>
>                 pio: pinctrl@01c20800 {
> -                       compatible = "allwinner,sun8i-h3-pinctrl";
> +                       /* compatible is in per SoC .dtsi file */
>                         reg = <0x01c20800 0x400>;
>                         interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
>                                      <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> @@ -588,17 +526,6 @@
>                         #size-cells = <0>;
>                 };
>
> -               gic: interrupt-controller@01c81000 {
> -                       compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> -                       reg = <0x01c81000 0x1000>,
> -                             <0x01c82000 0x2000>,
> -                             <0x01c84000 0x2000>,
> -                             <0x01c86000 0x2000>;
> -                       interrupt-controller;
> -                       #interrupt-cells = <3>;
> -                       interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;

The gic bits seem to be the same for both SoCs, aside from the
different compatible
string. Marc had sent a series to change them all to arm,gic-400, which is the
proper name for it, but it wasn't merged. I'm assuming the compatibles
are equal?
If so then it can also be shared.

The rest looks ok.

ChenYu

> -               };
> -
>                 rtc: rtc@01f00000 {
>                         compatible = "allwinner,sun6i-a31-rtc";
>                         reg = <0x01f00000 0x54>;
> --
> 2.11.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux