Re: [PATCH v2 6/7] Documentation: bindings: add documentation for ir-spi device driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Rob,

> > Document the ir-spi driver's binding which is a IR led driven
> > through the SPI line.
> >
> > Signed-off-by: Andi Shyti <andi.shyti@xxxxxxxxxxx>
> > ---
> >  Documentation/devicetree/bindings/media/spi-ir.txt | 26 ++++++++++++++++++++++
> >  1 file changed, 26 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/media/spi-ir.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/spi-ir.txt b/Documentation/devicetree/bindings/media/spi-ir.txt
> > new file mode 100644
> > index 0000000..85cb21b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/spi-ir.txt
> 
> Move this to bindings/leds, and CC the leds maintainers.

More than an LED this is the driver of a remote controller, the
driver itself is under drivers/media/rc/.

Besides all the transmitters have an LED but still they are media
devices. This is a bit special because it's so simple that the
only hardware left is the LED itself, but still it's a media remote
controller.

> > @@ -0,0 +1,26 @@
> > +Device tree bindings for IR LED connected through SPI bus which is used as
> > +remote controller.
> > +
> > +The IR LED switch is connected to the MOSI line of the SPI device and the data
> > +are delivered thourgh that.
> > +
> > +Required properties:
> > +       - compatible: should be "ir-spi".
> 
> Really this is just an LED connected to a SPI, so maybe this should
> just be "spi-led". If being more specific is helpful, then I'm all for
> that, but perhaps spi-ir-led. (Trying to be consistent in naming with
> gpio-leds).

As I mentioned above, all transmitters have an LED, but they do
not have the 'led' name. "ir-spi" is coherent with the device
driver name and the driver name is coherent with the media/rc
driver's naming.

> > +
> > +Optional properties:
> > +       - irled,switch: specifies the gpio switch which enables the irled/
> 
> As I said previously, "switch-gpios" as gpio lines should have a
> '-gpios' suffix. Or better yet, "enable-gpios" as that is a standard
> name for an enable line.

OK, thanks!

> > +       - negated: boolean value that specifies whether the output is negated
> > +         with a NOT gate.
> 
> Negated or inverted assumes I know what normal is. Define this in
> terms of what is the on state. If on is normally active low, then this
> should be led-active-high. There may already be an LED property for
> this.

Yes, thanks!

> > +       - duty-cycle: 8 bit value that stores the percentage of the duty cycle.
> > +         it can be 50, 60, 70, 75, 80 or 90.
> 
> This is percent time on or off?

Will add more details, thanks.

If it's OK for you, I would keep the name and documentation path
and fix the rest. Please let me know if I'm missing something :)

Thanks,
Andi
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux